About fhk-cwempe

fhk-cwempe · 08-09-2022

I was wondering if there are any features to help saving energy with Cisco access points. I know there are Power Saving Modes for VoIP phones.https://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/unified-ip-phone-6900-series/solut...

fhk-cwempe · 06-28-2022

I successfully stacked two C9500-48Y4C.The Uplink (single 10/100/1000BaseTX SFP) works fine. Then I tried to connect a C9200 with an LACP port-channel (Twe1/0/6 and Twe2/0/6).But I only get:%ETC-5-L3DONTBNDL2: Twe2/0/6 suspended: LACP currently not e...

fhk-cwempe · 01-10-2022

Hello,I have a strange issue. We are using static VPN IP adresses for most of our VPN users.The routes to this IPs are distributed via OSPF.They are created and deleted according to the VPN session. But there is one IP (from a specific user) that doe...

fhk-cwempe · 05-12-2021

I configured our new C9800 to send logs to our syslog server. logging facility local0 logging source-interface GigabitEthernet0 vrf Mgmt-intf logging host x.x.x.xAs you can see I want to send the messages via the out-of-band management interface.This...

fhk-cwempe · 05-11-2021

I wanted to check how much power our new Catalyst 9407 is consuming. The switch is configured and running.There is only one Access Point connected. No other clients. #sh power Power Fan States Sup...

fhk-cwempe · 08-10-2022

I think this is exactly what I was looking for.Thanks!Unfortunately, I think it will take a while until we can and will upgrade to IOS XE 17.8 on our controllers.Still need support for older APs.But that is another issue.

fhk-cwempe · 06-29-2022

After some troubleshooting tipps ("self loop test") from the sales person, I found out the issue was not between sfp module and C9500, but C9200. It was this bug.https://bst.cloudapps.cisco.com/bugsearch/bug/CSCwa11962 Update C9200 from 17.03.04b to ...

fhk-cwempe · 06-28-2022

But they should be compatible according to this: https://www.reddit.com/r/networking/comments/c8op1n/3rd_party_optics_cat_9500_highperformance/exvi2ik/?utm_source=reddit&utm_medium=web2x&context=3(search for "11555/SFP-10GLR-31") And the sales person...

fhk-cwempe · 06-28-2022

@balaji.bandi Like I said. I try to simplify the scenario and have not configured the port-channel anymore. @Reza Sharifi The Ports operate at 10G. C9500 Stack(I changed the port and hardware chassis in case 2/0/6 was defect) Port Name ...

fhk-cwempe · 06-28-2022

I know.I used channel-group mode active to create the Port-Channel. show etherchennel summary showes "LACP" as Protocol. But like I wrote, the issue seems to be deeper, even without port-channel. show stackwiseStackwise Virtual Configuration: -------...

Member Since	‎02-23-2016 07:04 AM
Date Last Visited	‎08-10-2022 12:04 AM
Posts	44
Total Helpful Votes Received	30

User Statistics

User Activity

Power Saving Mode for Access Points?

0 packets input on C9500-48Y4C StackWise Virtual Switch

OSPF route stuck on ASA for VPN users IP address

Change sender domain for syslog messages

C9407 show power incorrect

Re: Power Saving Mode for Access Points?

Re: 0 packets input on C9500-48Y4C StackWise Virtual Switch

Re: 0 packets input on C9500-48Y4C StackWise Virtual Switch

Re: 0 packets input on C9500-48Y4C StackWise Virtual Switch

Re: 0 packets input on C9500-48Y4C StackWise Virtual Switch