About sergiodovinte

sergiodovinte · 01-28-2011

Let me explain what i want to achieve...We have a remote site with a "fragile" WAN link. It has a router 2821 with a T1 PRI configured on it.The T1 is configured with MGCP and when the WAN connection fails, we suffer an outage on the T1 while falling...

sergiodovinte · 01-11-2011

I have a T1 PRI dms-100 over MGCP.There is a Translation Pattern that routes the T1 numeration to a Hunt Pilot -2100-. This is a assigned to a Hunt List and a Line Group of extensions where the operators answer the calls.My problem is that I'm not re...

sergiodovinte · 12-14-2010

I have a 2821 router connected trough VPN with a CallManager 4.2.It has a T1 CAS configured that now, works ok in SRST mode but I have problems with it and MGCP:In MGCP mode, when we place inbound calls it always matches the srst dial-peers and phone...

sergiodovinte · 12-02-2010

I have a 2800 router connected trough VPN with a CallManager 4.2. It has a T1 CAS configured and it works ok with MGCP.My problem is when the connection between the router and the CM fails and the SRST mode is enabled.If I call the T1 number I can he...

sergiodovinte · 01-31-2011

Hi there and thanks for your answer. **Move to H323 for T1/E1 Calls*** ---> Yep, I'm going to try to configure the gateway as H323 and create the apropiate dial-peers and see what happens...**Move to a CME SETUP (Phones registered to CME, Dialpeers t...

sergiodovinte · 12-15-2010

Luis, I've removed that line and now, over MGCP mode an incoming call matches the correct dial-peer with service Mgcpapp.For Outgoing calls i have the same problem over MGCP, I can place only one call and it matches the SRST dial-peer 8000 (see below...

sergiodovinte · 12-09-2010

Finally I've solved the problem.voice translation-rule 1rule 1 /.*/ /2100/That rule pointed to 2100, that's a Hunt Pilot created in the CallManager.While in SRST mode, CallManager is not accesible, so the router can't reach that 2100 group.I created ...

sergiodovinte · 12-03-2010

With those peers added the situation remains the same:GW-S#sh voice call statCallID CID ccVdb Port DSP/Ch Called # Codec Dial-peers0x4B 126D 0x48A411F4 0/1/0:1.1 0/1:1 * None 8000/-1 active call foundGW-S...

sergiodovinte · 12-03-2010

Hello Madhusudhan and thank you for your answer.Yes, I already know that, I forgot to include theese peers on the configuration output:dial-peer voice 8000 pots description INCOMING T1 CAS Mode SRST incoming called-number . port 0/1/0:1!dial-peer voi...

Member Since	‎12-02-2010 12:38 PM
Date Last Visited	‎08-18-2017 03:55 AM
Posts	10

User Statistics

User Activity

Configure T1 PRI without CallManager intervention

Calling Party 'Unknown Number' over T1 PRI

T1 CAS MGCP in-outbound calls

Incoming calls T1 CAS on SRST gateway. Phones doesn't ring and no codec.

Re: Configure T1 PRI without CallManager intervention

Re: T1 CAS MGCP in-outbound calls

Re: Incoming calls T1 CAS on SRST gateway. Phones doesn't ring a

Re: Incoming calls T1 CAS on SRST gateway. Phones doesn't ring a

Re: Incoming calls T1 CAS on SRST gateway. Phones doesn't ring a