Hi there, Under Service paramters > Call Manager services > Clusterwide Parameters (Feature - Conference) I can see the services you are talking about, our cucm 8.6.2.   Please check if you have a MRGL assigned to your DX650 phones and the MRGL has the resources required for conferencing. I'll try dig up some more info but maybe tac is an option.   Good luck!   Cheers ... View more

Hi there,   We have it working, this was quite a long time ago, I cannot remember what exactly we did.   There is a video calling feature under the device configuration of the DX650, make sure this is enabled.   Also try upgrading the firmware if the above fails, we found newer more stable releases a few years back, just note the the display settings are different between firmware releases. ... View more

Sorry for late reply the issue ended up being an assymetric routing issue. ... View more

Did you ever find the location? ... View more

Thanks Ayodeji,   The thing is when " Run on All active Nodes" feature is checked the outbound calls are routed by using the route local rule. In the scario that I have noted this rule always picks the trunk associated with this RL and ignores other RG with gateways. It always uses the standard local route group. Unchecking Run on all active nodes is a workaround for us with no other issues :-). Very interesting arcticle and very informative! ... View more

Thanks this is a great report. We run a complex environment and I would like to share a scenario:   We have SIP Trunks in CUCM connected to SIP Cubes We have RL used for TEHO into another country Both of these had the " Run on all CUCM nodes" check box selected.   Phones registered to two of our subscribers were experiencing calls that were being routed out our SIP cubes and NOT via the TEHO RL and RG's associated to them. In this case, just for this TEHO scenario it appears unchecking "Run on all CUCM nodes" on the TEHO RL forces the calls to use the TEHO RL and not the local sip cubes - saving international costs.   Seems to work, ok Intracluster communications comes into play but this scenario is only used in TEHO RL.. Keen to see if you guys have any other ideas or better ways to implement...     ... View more

Hello,   Our organisation is looking at rolling out Win8.1, these post replys are 4months old.   Has anyone managed to get around the 'unsupported' issue between CAD and Win8? Or does anyone have an update on any information from Cisco?   Thanks ... View more

Hello, I have followed your instructions but still no luck.   1. run sql select * from callingsearchspace 2. pkid is "9c679ca2-4828-dd80-044b-5fd4e576998c" 3. ** Here I have too use the scfa as this css we cant delate is on the scfa, the values I get are below run sql select fknumplan from callforwarddynamic where  fkcallingsearchspace_scfa = "9c679ca2-4828-dd80-044b-5fd4e576998c" fknumplan                            ==================================== 6d9727c7-e235-bc1f-cdf4-ff5578d4f0d6 ba2729d9-91fa-9363-a84b-11a65a32eb7c   4. ** This command get error, I tried both pkid and fknumplan entries and the same admin:run select dnorpattern from numplan where pkid = "6d9727c7-e235-bc1f-cdf4-ff5578d4f0d6" Executed command unsuccessfully No valid command entered admin:run select dnorpattern from numplan where pkid = "9c679ca2-4828-dd80-044b-5fd4e576998c" Executed command unsuccessfully No valid command entered admin:   Any ideas? Anyone able to help?                 ... View more

Hi Guys, Tried clearing the counters as per Nadeem's post - still no go. Heres the sh ver below, Thanks Sambit ill look into that caveat g1#sh ver Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.2(4)M4, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Thu 20-Jun-13 13:30 by prod_rel_team ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1) au-nsw-pem-adm-g1 uptime is 18 weeks, 17 hours, 19 minutes System returned to ROM by INVALID Switchover at 16:13:51 AEST Wed Aug 14 2013 System restarted at 16:15:58 AEST Wed Aug 14 2013 System image file is "flash0:c2951-universalk9-mz.SPA.152-4.M4.bin" Last reload type: Normal Reload Last reload reason: Reload Command Cisco CISCO2951/K9 (revision 1.1) with 1007616K/40960K bytes of memory. Processor board ID FGL1651127R 3 Gigabit Ethernet interfaces 1 terminal line DRAM configuration is 72 bits wide with parity enabled. 255K bytes of non-volatile configuration memory. 500472K bytes of ATA System CompactFlash 0 (Read/Write) Configuration register is 0x2102 ... View more