About grzegorzniecka

grzegorzniecka · 04-15-2014

Dear all,my existing catalyst 2960 config for vlans:...interface FastEthernet0/2 description 3Com Switch switchport access vlan 10 switchport mode access...interface FastEthernet0/5 description to Cyberoam switchport mode trunk...interface FastEthern...

grzegorzniecka · 04-25-2013

Hi all,7911 is registering endlesslly.It holds on:Apr 25 12:54:59.651 CDT: TFTP: Looking for CTLSEPD824BDBA2483.tlvApr 25 12:54:59.731 CDT: TFTP: Looking for ITLSEPD824BDBA2483.tlvApr 25 12:54:59.811 CDT: TFTP: Looking for ITLFile.tlvApr 25 12:55:00....

grzegorzniecka · 05-14-2012

Dear all,I have configured ISR2811:interface FastEthernet0/0.90encapsulation dot1Q 90ip address 172.16.1.1 255.255.255.0How to set up trunk on (for example) G1 interface on switch SF300-48P?And next,how to set up interface(s) to be in this Vlan90?Reg...

grzegorzniecka · 04-13-2012

Dear all,undervoice register globalthere should be also create profile sync ...what this command is used for?Regards

grzegorzniecka · 04-10-2012

Dear all,from todays morning my 2921 is restarting about one time per two hours:uptime is 1 minuteSystem returned to ROM by bus error at PC 0x23A49808, address 0x0 at 15:45:07 CET Tue Apr 10 2012System restarted at 15:46:39 CET Tue Apr 10 2012System ...

grzegorzniecka · 04-26-2013

I have TAC webex.Durning webex when we have shutdown/no shutdown telepgoney service error message appears:%SKINNYSERVER-3-NOINIT: Can't initialize Skinny serverthey suggest me to try on lower IOS version - I have tried and still I get this message.

grzegorzniecka · 04-26-2013

Have do it before - after hard reset telephone upgrades its software but at the end still get registering...

grzegorzniecka · 04-26-2013

Still no luck,my actual settings:telephony-service max-ephones 24 max-dn 48 ip source-address 172.16.100.1 port 2000 cnf-file location flash: load 7911 SCCP11.9-3-1SR2-1S time-zone 23 max-conferences 8 gain -6 transfer-system full-consult create cnf-...

grzegorzniecka · 04-25-2013

Still no luck...My settings are (cnf recreated):telephony-service max-ephones 24 max-dn 48 ip source-address 172.16.100.1 port 2000 cnf-file location flash: load 7911 SCCP11.9-3-1SR2-1S time-zone 23 max-conferences 8 gain -6 transfer-system full-cons...

grzegorzniecka · 04-25-2013

I have download new firmware:cmterm-7911_7906-sccp.9-3-1SR2-1.zipI have unzipped it and copied one by one file to router flash.Then I have restarted my 7911.And no matter if I have:load 7911 SCCP11.9-3-1SR2-1S orload 7911 SCCP11.9-3-1SR2-1S.loadsmy 7...

Member Since	‎06-27-2008 04:42 AM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	74
Total Helpful Votes Received	5

User Statistics

User Activity

Moving VLAN config from catalyst 2960 to SG300

7911 not registering

SF300-48P - trunk to ISR2811

create profile sync - what this command is used for?

New ISRG2 2921 restarts very often.

Re: 7911 not registering

Re: 7911 not registering

Re: 7911 not registering

Re: 7911 not registering

7911 not registering