cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3413
Views
0
Helpful
14
Replies

7911 not registering

grzegorzniecka
Level 1
Level 1

Hi all,

7911 is registering endlesslly.

It holds on:

Apr 25 12:54:59.651 CDT: TFTP: Looking for CTLSEPD824BDBA2483.tlv

Apr 25 12:54:59.731 CDT: TFTP: Looking for ITLSEPD824BDBA2483.tlv

Apr 25 12:54:59.811 CDT: TFTP: Looking for ITLFile.tlv

Apr 25 12:55:00.079 CDT: TFTP: Looking for SEPD824BDBA2483.cnf.xml

Apr 25 12:55:00.083 CDT: TFTP: Opened flash:/its/vrf1/XMLDefault7911.cnf.xml, fd 9, size 1286 for process 187

Apr 25 12:55:00.087 CDT: TFTP: Finished flash:/its/vrf1/XMLDefault7911.cnf.xml, time 00:00:00 for process 187

Apr 25 12:55:04.111 CDT: TFTP: Looking for English_United_States/tc-sccp.jar

Apr 25 12:55:07.363 CDT: TFTP: Looking for United_States/g3-tones.xml

and it stops...

my tftp-bindings:

tftp-server flash:/its/united_states_7960-tones.xml alias United_States/7960-tones.xml

tftp-server flash:/its/united_states_7960-font.xml alias English_United_States/7960-font.xml

tftp-server flash:/its/united_states_7960-font.xml alias English_United_States/7920-font.xml

tftp-server flash:/its/united_states_7960-dictionary.xml alias English_United_States/7960-dictionary.xml

tftp-server flash:/its/united_states_7960-kate.xml alias English_United_States/7960-kate.xml

tftp-server flash:/its/united_states_7960-kate.xml alias English_United_States/7920-kate.xml

tftp-server flash:/its/united_states_SCCP-dictionary.xml alias English_United_States/SCCP-dictionary.xml

tftp-server flash:/jar11sccp.9-2-3TH1-9.sbn alias jar11sccp.9-2-3TH1-9.sbn

tftp-server flash:/cnu11.9-2-3TH1-9.sbn alias cnu11.9-2-3TH1-9.sbn

tftp-server flash:/apps11.9-2-3TH1-9.sbn alias apps11.9-2-3TH1-9.sbn

tftp-server flash:/dsp11.9-2-3TH1-9.sbn alias dsp11.9-2-3TH1-9.sbn

tftp-server flash:/cvm11sccp.9-2-3TH1-9.sbn alias cvm11sccp.9-2-3TH1-9.sbn

tftp-server flash:/SCCP11.9-2-3S.loads alias SCCP11.9-2-3S.loads

tftp-server flash:/its/vrf1/XMLDefault7911.cnf.xml alias SEPD824BDBA2483.cnf.xml

tftp-server flash:/its/SEPDEFAULT.cnf alias SEPDefault.cnf

tftp-server flash:/its/vrf1/XMLDefault.cnf.xml alias XMLDefault.cnf.xml

tftp-server flash:/its/vrf1/ATADefault.cnf.xml alias ATADefault.cnf.xml

my config:

telephony-service

max-ephones 24

max-dn 48

ip source-address 172.16.100.1 port 2000

cnf-file location flash:

load 7911 SCCP11.9-2-3S.loads

time-zone 23

max-conferences 8 gain -6

transfer-system full-consult

create cnf-files version-stamp 7960 Apr 25 2013 12:58:12

!

!

ephone-dn  10  dual-line

number 1000

!

!

ephone  10

device-security-mode none

mac-address D824.BDBA.2483

type 7911

button  1:10

What could be the issue?

Regards

GN

14 Replies 14

yahsiel2004
Level 7
Level 7

Have you verified the firmware directory in flash? Have you verified that you have the correct firmware, you put ".loads" I think it should be ".sbin". Verify your tftp and alias are correct.

Regards,

Yosh

HTH Regards, Yosh

Have you verified that you have the correct firmware.

how can I verify that?

Verify your tftp and alias are correct.

I have do this aliases by myself?

Regards

GN

hello

you can verify from Cisco site by using the below link for 79xx phones

http://software.cisco.com/download/navigator.html?mdfid=269065653&catid=278875240

Please try the my below post , i think this is the issue.

Thank you

please rate if this will help

islam.kamal
Level 10
Level 10

Hello

please try the below without extension

telephony-service

load 7911 SCCP11.9-2-3S

no create-cnf

create-cnf

thank you

please rate if this will help

I have download new firmware:

cmterm-7911_7906-sccp.9-3-1SR2-1.zip

I have unzipped it and copied one by one file to router flash.

Then I have restarted my 7911.

And no matter if I have:

load 7911 SCCP11.9-3-1SR2-1S

or

load 7911 SCCP11.9-3-1SR2-1S.loads

my 7911 still is registering endlessly at:

Apr 25 14:19:43.887 CDT: TFTP: Looking for English_United_States/tc-sccp.jar

Apr 25 14:19:45.095 CDT: TFTP: Looking for United_States/g3-tones.xml

should I have this additionl tftp bindings?

Regards

GN

Hello

Please you have to use the command under telephony-service without .loads. Then under telephony-service  no create cnf create cnf

Thank you

please rate if this will help

Still no luck...

My settings are (cnf recreated):

telephony-service

max-ephones 24

max-dn 48

ip source-address 172.16.100.1 port 2000

cnf-file location flash:

load 7911 SCCP11.9-3-1SR2-1S

time-zone 23

max-conferences 8 gain -6

transfer-system full-consult

create cnf-files version-stamp 7960 Apr 25 2013 15:18:33

On my 7911 in right upper corner shows 1000 while my numer configuration is:

ephone-dn  10  dual-line

number 999

ephone  10

device-security-mode none

mac-address D824.BDBA.2483

type 7911

Regards

GN

hello

can you delete ephone 10   , and remove the phone from your network .After that readd  ephone 10 then add the phone

to your netwrok .

did you do no create cnf then   create cnf?. I do not see button 1:10 under ephone 10 configuration , please clarrify

Thank you

please rate if this will help

try putting the button 1:10 , under ephone 10

Still no luck,

my actual settings:

telephony-service

max-ephones 24

max-dn 48

ip source-address 172.16.100.1 port 2000

cnf-file location flash:

load 7911 SCCP11.9-3-1SR2-1S

time-zone 23

max-conferences 8 gain -6

transfer-system full-consult

create cnf-files version-stamp 7960 Apr 26 2013 09:22:42

!

!

ephone-dn  10

number 999

name test

!

!

ephone  10

device-security-mode none

mac-address D824.BDBA.2483

type 7911

button  1:10

and my telephone - why he has such date and time when on my CME is

#sh clock

09:47:55.503 CDT Fri Apr 26 2013

Hi Grzegorz niecka,

check with factory default setting.

1. check DHCP : enable ( If your network DHCP enabled)

2. Power off the phone

3. Power on and hold # key for few seconds.

4. Led's are blinking then press 123456789*0#

5. It will restart and upgrade with your tftp server settings

Thanks

Have do it before - after hard reset telephone upgrades its software but at the end still get registering...

grzegorzniecka
Level 1
Level 1

I have TAC webex.

Durning webex when we have shutdown/no shutdown telepgoney service error message appears:

%SKINNYSERVER-3-NOINIT: Can't initialize Skinny server

they suggest me to try on lower IOS version - I have tried and still I get this message.

Hi Grzegorz

Try delete the CTL file,

Settings > Security > Trust List > ITL File > **# (to unlock the settings) > Erase

Cheers
Bruno Rangel

please rate if this help

Cheers
Bruno Rangel
Please remember to rate helpful responses using the star bellow and identify helpful or correct answers