I have tired to remove in running config the no command does not work. I then uploaded a new configuration without redundancy to startup and reloaded still the redundancy command comes back.
... View more
Don't see show interface wired 0 under apciscoshell AP00A7.42C3.5EFE>show arp Show ARP table authentication Local authentication process information avc AVC show commands ble Bluetooth Low Energy show commands boot Show boot attributes capwap CAPWAP Show Options class-map Show CPL Class Map cli Show Command line clock Display the system clock controllers Dot11 interface controller status crypto Show crypto attributes cts Cisco Trusted Security information debug show the debugs enabled dhcp Dynamic Host Configuration Protocol status dtls DTLS show commands filesystems Display filesystem information flash Flash contents flexconnect AP flexconnect information inventory Show the physical inventory ip IP information ipv6 IPv6 information kernel Kernel show commands led Show LED information policy-map Show CPL Policy Map processes show list of processes cpu and memory utilization rrm Radio Resource Management Show Options trace Trace Events Options version Display image version wips Show wIPS Information wired Show Wired network information
... View more
well that intresting... The mgig supplies the power, but interface show not connected.
Gi1/0/39 auto on 15.4 Ieee PD 4 30.0 Gi1/0/40 auto off 0.0 n/a n/a 30.0 Gi1/0/41 auto off 0.0 n/a n/a 30.0 Gi1/0/42 auto off 0.0 n/a n/a 30.0 Gi1/0/43 auto off 0.0 n/a n/a 30.0 Gi1/0/44 auto off 0.0 n/a n/a 30.0 Gi1/0/45 auto off 0.0 n/a n/a 30.0 Gi1/0/46 auto off 0.0 n/a n/a 30.0 Gi1/0/47 off off 0.0 n/a n/a 30.0 Gi1/0/48 auto off 0.0 n/a n/a 30.0 dvl-240-1#show int g1/0/39 GigabitEthernet1/0/39 is down, line protocol is down (notconnect) Hardware is Gigabit Ethernet, address is f41f.c261.40a7 (bia f41f.c261.40a7) MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Auto-duplex, Auto-speed, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
... View more