Hi, I have 5 Cisco 1852 mobility express access points and have all been working fine. But in the last week 4 of the access points keep flapping between standalone and connected mode. I've tried rebooting the access points which join the controller but then disconnect. The software version on all the access points is 8.5.120.0. Find below the logs from one I rebooted today:   Depot-AP01#show log System logging: Sep 5 00:48:23 syslogd started: BusyBox v1.23.2 Sep 5 00:48:23 kernel: printkd started: BusyBox v1.23.2 (2018-01-30 02:33:23 PST) Sep 5 00:48:23 kernel: klogd started: BusyBox v1.23.2 (2018-01-30 02:33:23 PST) Sep 5 00:48:23 kernel: [*01/01/1970 00:00:37.2985] buginf() enabled. Sep 5 00:48:23 kernel: [*01/01/1970 00:00:37.3085] Made it into bootsh: Jan 30 2018 02:54:22 Sep 5 00:48:23 kernel: [*01/01/1970 00:00:37.3085] bootsh build T-aa5421185f6af7f1b26f46379e8dc11f6136c54c-gaa542118-vipendya Sep 5 00:48:23 kernel: [*01/01/1970 00:00:39.0279] ^Minit started: BusyBox v1.23.2 (2018-01-30 02:33:23 PST) Sep 5 00:48:23 kernel: [*01/01/1970 00:00:40.7674] GCM-128 POST passed Sep 5 00:48:23 kernel: [*01/01/1970 00:00:40.7674] GCM-256 POST passed Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.0873] Active version: 8.5.120.0 Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.0973] Backup version: 8.3.112.0 Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.3272] Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.3272] led pattern module start Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.4072] AP1852I Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.5272] nss_driver - Turbo Support 1 Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.5272] Supported Frequencies - 110Mhz 550Mhz 733Mhz Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.5572] NSS firmware booted Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.5871] NSS firmware booted Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.6771] Sep 5 00:48:23 kernel: [*01/01/1970 00:00:41.6771] phy_value=0: org="0x1000" phy_reg="0x1800" Sep 5 00:48:23 kernel: [*01/01/1970 00:00:42.0270] Current value of FACTORY_RESET=0 Sep 5 00:48:23 kernel: [*01/01/1970 00:00:42.0470] Last reload time: Sep 5 00:48:23 2018 Sep 5 00:48:23 kernel: [*09/05/2018 00:48:23.0000] Setting system time Wed Sep 5 00:48:23 UTC 2018 Sep 5 00:48:23 kernel: [*09/05/2018 00:48:23.0599] device wired0 entered promiscuous mode Sep 5 00:48:23 kernel: [*09/05/2018 00:48:23.1299] device wired1 entered promiscuous mode Sep 5 00:48:23 kernel: [*09/05/2018 00:48:23.5798] stile module dp init successfully Sep 5 00:48:23 kernel: [*09/05/2018 00:48:23.5798] NBAR Label:BLD_MCP_DEV_LATEST_20150424_123021 NBAR VERSION:module build date: Jan 30 2018 at 02:50:55 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:23.9897] ADDRCONF(NETDEV_UP): wired0: link is not ready Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.0297] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.2696] miibus get ef438c00! Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.2996] Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3096] boot 268 build T-aa5421185f6af7f1b26f46379e8dc11f6136c54c-gaa542118-vipendya board corsica mac DC:CE:C1:20:13:88 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: mbedtls .text=0xbf000000 data=0xbf007e18 bss=0xbf008070 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: aptrace .text=0xbf00c000 data=0xbf018834 bss=0xbf018cc0 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: led_module .text=0xbf020000 data=0xbf0204e0 bss=0xbf020b48 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: qca_nss_gmac .text=0xbf024000 data=0xbf02abc0 bss=0xbf02b084 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: qca_nss_drv .text=0xbf034000 data=0xbf04fb60 bss=0xbf050910 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: qca_nss_capwapmgr .text=0xbf071000 data=0xbf075acc bss=0xbf075c20 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: nssmgrctl .text=0xbf07c000 data=0xbf07d70c bss=0xbf07da30 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: proclikefs .text=0xbf083000 data= bss=0xbf083b40 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: stile_lm_ft .text= data= bss= Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: stile_lm_dp .text= data= bss= Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: ipv6 .text=0xbfa07000 data=0xbfa37f00 bss=0xbfa397ac Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: bonding .text=0xbfa53000 data=0xbfa64628 bss=0xbfa64a54 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: lowmemorykiller .text=0xbfa71000 data=0xbfa712c0 bss=0xbfa7144c Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: qca_nss_profile_drv .text=0xbfa75000 data=0xbfa76320 bss=0xbfa76494 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: scsi_wait_scan .text= data= bss= Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3196] Module: ssdk_reg .text=0xbfa7f000 data= bss=0xbfa7f838 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.3696] phram: phram-oops device: 0x2000 at 0x42520000 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.6695] phram: phram-oops device: 0x10000 at 0x42500000 Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.7594] ramoops: platform device not found, using module parameters Sep 5 00:48:24 kernel: [*09/05/2018 00:48:24.7994] Last reload reason : 1: reload command Sep 5 00:48:25 FIPS[2445]: *** fastcgi: FIPS Mode = disabled *** Sep 5 00:48:25 FIPS[2447]: *** fastcgi: FIPS Mode = disabled *** Sep 5 00:48:26 FIPS[2450]: *** brain: FIPS Mode = disabled *** Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.3589] ADDRCONF(NETDEV_CHANGE): wired0: link becomes ready Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.3689] wired0: 1000 Mbps Full Duplex Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.3689] Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 rmmod: module is not loaded Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4189] __mm_init_module Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4389] ath_dfs: Version 2.0.0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4389] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] ath_ol_pci: (Atheros/multi-bss) Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] ol_ath_pci_probe: PCI device id 0040 :0040 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] *********** Beeliner ************* Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] __ol_ath_attach() Allocated scn ee080480 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] ol_ath_pci_configure : num_desired MSI set to 0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] Using PCI Legacy Interrupt Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4689] chip_id 0x9 chip_revision 0x1 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] CLOCK PLL skipped Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] HIF_PCIDeviceProbed: setting the target pll frac ffffffff intval ffffffff Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] HIF_PCIDeviceProbed: no frac provided, skipping pre-configuring PLL Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] HIF_PCIDeviceProbed: targ_clk is not provided, skipping pre-configuring PLL Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] __ol_ath_attach: dev name wifi0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] ol_ath_attach interface_id 0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] ol_target_init() BMI inited. Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] ol_target_init() BMI Get Target Info. Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] Chip id: 0x9, chip version: 0x1000000 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4789] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4989] qc98xx_verify_checksum: flash checksum passed: 0xef28 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4989] ol_transfer_bin_file 3974: Download Flash data len 12064 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.4989] Board extended Data download address: 0x0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5189] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5189] Board data initialized Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5189] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5189] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5189] Selecting OTP binary for CHIP Version 1 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5289] ol_transfer_bin_file 3793: downloading file 0, Download data len 11100 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5689] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5689] First OTP send param 8000 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5689] ol_ath_download_firmware :First OTP download and Execute is good address:0xa000 return param 4660 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5689] ol_ath_download_firmware:##Board Id 8 , CHIP Id 1 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5689] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5689] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS260_negative_pwr_offset_2G_v2_008.bin Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5789] ol_transfer_bin_file 3793: downloading file 3, Download data len 12064 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5789] Board extended Data download address: 0x0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5989] ol_ath_download_firmware: Using 0x1234 for the remainder of init Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5989] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.5989] Selecting OTP binary for CHIP Version 1 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6189] ol_transfer_bin_file 3793: downloading file 0, Download data len 11100 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6489] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6489] [Flash] : Ignore Module param Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6489] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6489] Second otp download Param 10000 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6489] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6489] Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6489] Mission mode: Firmware CHIP Version 1 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6589] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6788] Swap: bytes_left to copy: fw:16; dma_page:76179 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6788] Swap: wrong length read:0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6788] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 185965 Target address 417fe0 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6788] scn=ee080480 target_write_addr=417fe0 seg_info=ee604610 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6788] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6788] bin_filename=AR900B/hw.2/athwlan.bin swap_filename=/lib/firmware/AR900B/hw.2/athwlan.codeswap.bin Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6788] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin Sep 5 00:48:26 kernel: [*09/05/2018 00:48:26.6888] ol_transfer_bin_file 3793: downloading file 1, Download data len 362100 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7685] ol_target_init() Download FW done. Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7685] ol_ath_attach() WMI attached. wmi_handle ed100000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7685] htc_wmi_init() HT Create . c49af000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7685] htc_wmi_init() HIF Claim. Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7685] htc_wmi_init 7842 host_enable 0 nss_nwifi_offload 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7685] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7685] OL_ACBKMinfree : 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] OL_ACBEMinfree : 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] OL_ACVIMinfree : 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] OL_ACVOMinfree : 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] CE_recv_buf_enqueue 877 Populate last entry 512 for CE 5 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] CE_recv_buf_enqueue 886 CE 5 wi 511 dest_ptr 0x6e0f7040 nbytes 0 recv_ctxt 0xecb48200 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] HTC Rx: insufficient length, got:4 expected =8 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] Startup Mode-0 set Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] <=== cfg max peer id 1056 ====> Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] HTC Service:0x0300 ep:1 TX flow control disabled Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] CE_pkt_dl_len_set CE 4 Pkt download length 64 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from ec920000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] HTC Service:0x0100 ep:2 TX flow control disabled Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] Firmware_Build_Number:70 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339a79b2 vht_supp_mcs:0x0000ffaa Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] RES CFG Support wmi_service_bitmap 9778 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 50 to TGT Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] ol_ath_service_ready_event: tt_support: 1 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] ol_ath_service_ready_event: periodic_chan_stats: 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] Peer Caching Enabled ; num_peers = 234, num_active_peers = 53 num_tids = 106, num_vdevs = 18 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 54 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 54 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 54 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1272 actual units 235 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] idx 6 req 5 num_units 0 num_unit_info 2 unit size 1920 actual units 235 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] chunk 0 len 13824 requested ,ptr 0x6ddac000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] chunk 1 len 55296 requested ,ptr 0x6de10000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] chunk 2 len 221184 requested ,ptr 0x6de80000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] chunk 3 len 298920 requested ,ptr 0x6df00000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] chunk 4 len 107520 requested ,ptr 0x6dec0000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] chunk 5 len 6144 requested ,ptr 0x6dee0000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.7785] chunk 6 len 451200 requested ,ptr 0x6df80000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] wmi_ready_event_rx: WMI UNIFIED READY event Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] ol_ath_connect_htc() WMI is ready Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] ol_ath_attach() connect HTC. Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] bypasswmi : 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] target uses HTT version 2.2; host uses 2.2 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] ol_ath_phyerr_attach: called Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] OL Resmgr Init-ed Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] acfg_attach: 3522: Netlink socket created:c4aafa00 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] Green-AP : Green-AP : Attached Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8585] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] __ol_ath_attach: dev name wifi1 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] ol_ath_attach interface_id 1 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] ol_target_init() BMI inited. Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] ol_target_init() BMI Get Target Info. Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] Chip id: 0x9, chip version: 0x1000000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] CE WAR Disabled Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] ol_target_init() configure Target . Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8785] Target Version is 1000000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8985] qc98xx_verify_checksum: flash checksum passed: 0xd012 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8985] ol_transfer_bin_file 3974: Download Flash data len 12064 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.8985] Board extended Data download address: 0x0 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9185] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9185] Board data initialized Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9185] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9185] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9185] Selecting OTP binary for CHIP Version 1 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9285] ol_transfer_bin_file 3793: downloading file 0, Download data len 11100 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9684] Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9684] First OTP send param 8000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9684] ol_ath_download_firmware :First OTP download and Execute is good address:0x9c00 return param 4660 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9684] ol_ath_download_firmware:##Board Id 7 , CHIP Id 1 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9684] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9684] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS239_negative_pwr_offset_5G_v2_007.bin Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9784] ol_transfer_bin_file 3793: downloading file 3, Download data len 12064 Sep 5 00:48:27 kernel: [*09/05/2018 00:48:27.9784] Board extended Data download address: 0x0 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:27.9984] ol_ath_download_firmware: Using 0x1234 for the remainder of init Sep 5 00:48:28 kernel: [*09/05/2018 00:48:27.9984] Sep 5 00:48:28 kernel: [*09/05/2018 00:48:27.9984] Selecting OTP binary for CHIP Version 1 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0084] ol_transfer_bin_file 3793: downloading file 0, Download data len 11100 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0484] Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0484] [Flash] : Ignore Module param Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0484] Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0484] Second otp download Param 10000 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0484] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0484] Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0484] Mission mode: Firmware CHIP Version 1 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0584] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0684] Swap: bytes_left to copy: fw:16; dma_page:76179 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0684] Swap: wrong length read:0 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0684] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 185965 Target address 417fe0 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0784] scn=ec3c0480 target_write_addr=417fe0 seg_info=ee604e10 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0784] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0784] bin_filename=AR900B/hw.2/athwlan.bin swap_filename=/lib/firmware/AR900B/hw.2/athwlan.codeswap.bin Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0784] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.0884] ol_transfer_bin_file 3793: downloading file 1, Download data len 362100 Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.7782] FWLOG: [47798] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.7782] FWLOG: [47798] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.7782] FWLOG: [47798] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:28 kernel: [*09/05/2018 00:48:28.7782] FWLOG: [47798] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] ol_target_init() Download FW done. Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] ol_ath_attach() WMI attached. wmi_handle ed930000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] htc_wmi_init() HT Create . ed081000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] htc_wmi_init() HIF Claim. Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] htc_wmi_init 7842 host_enable 0 nss_nwifi_offload 0 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] OL_ACBKMinfree : 0 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] OL_ACBEMinfree : 0 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] OL_ACVIMinfree : 0 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] OL_ACVOMinfree : 0 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1681] CE_recv_buf_enqueue 877 Populate last entry 512 for CE 5 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] Firmware_Build_Number:70 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339b79b2 vht_supp_mcs:0x0000ffaa Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] RES CFG Support wmi_service_bitmap 9778 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 50 to TGT Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] ol_ath_service_ready_event: tt_support: 1 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] ol_ath_service_ready_event: periodic_chan_stats: 0 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] Peer Caching Enabled ; num_peers = 234, num_active_peers = 53 num_tids = 106, num_vdevs = 18 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 54 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 54 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 54 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1272 actual units 235 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] idx 6 req 5 num_units 0 num_unit_info 2 unit size 1920 actual units 235 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] chunk 0 len 13824 requested ,ptr 0x6e57c000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] chunk 1 len 55296 requested ,ptr 0x6da40000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] chunk 2 len 221184 requested ,ptr 0x6da80000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] chunk 3 len 298920 requested ,ptr 0x6db00000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] chunk 4 len 107520 requested ,ptr 0x6da60000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] chunk 5 len 6144 requested ,ptr 0x6e578000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.1781] chunk 6 len 451200 requested ,ptr 0x6db80000 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] wmi_ready_event_rx: WMI UNIFIED READY event Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] ol_ath_connect_htc() WMI is ready Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] ol_ath_attach() connect HTC. Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] bypasswmi : 0 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] target uses HTT version 2.2; host uses 2.2 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] ol_ath_phyerr_attach: called Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] OL Resmgr Init-ed Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] acfg_attach: Offload using existing sock c4aafa00 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] Green-AP : Green-AP : Attached Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] Green-AP : Attached Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] rate power table override is only supported for AR98XX Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] ol_if_dfs_setup: called Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] ol_if_dfs_attach: called; ptr=ed951984, radar_info=ee531b90 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] ol_ath_attach() UMAC attach . Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2480] BURSTING enabled by default Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2580] ACS not enabled Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2580] __ol_ath_attach: needed_headroom reservation 60 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2580] ol_ath_thermal_mitigation_attach: -- Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2780] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2780] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2880] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2980] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.2980] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.4280] ADDRCONF(NETDEV_UP): wired1: link is not ready Sep 5 00:48:29 dnsmasq[2660]: started, version 2.78 cachesize 150 Sep 5 00:48:29 dnsmasq[2660]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify Sep 5 00:48:29 dnsmasq[2660]: read /etc/hosts - 3 addresses Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.4680] brain: unloading click config Sep 5 00:48:29 kernel: [*09/05/2018 00:48:29.4680] brain: spring cleaning pages Sep 5 00:48:30 kernel: [*09/05/2018 00:48:30.1678] FWLOG: [49180] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:30 kernel: [*09/05/2018 00:48:30.1678] FWLOG: [49180] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:30 kernel: [*09/05/2018 00:48:30.1678] FWLOG: [49180] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:30 kernel: [*09/05/2018 00:48:30.1678] FWLOG: [49180] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) Sep 5 00:48:30 kernel: [*09/05/2018 00:48:30.6276] brain: loading click config Sep 5 00:48:31 kernel: [*09/05/2018 00:48:31.3274] pid 2450's current affinity mask: 3 Sep 5 00:48:31 kernel: [*09/05/2018 00:48:31.3274] pid 2450's new affinity mask: 1 Sep 5 00:48:32 kernel: [*09/05/2018 00:48:32.8969] click-config/io-real.click:131: While configuring 'todev_wired0 :: ToDevice': Sep 5 00:48:32 kernel: [*09/05/2018 00:48:32.8969] warning: device 'wired0' is down Sep 5 00:48:32 kernel: [*09/05/2018 00:48:32.9369] click-config/io-real.click:131: While configuring 'fromdev_wired0 :: FromDevice': Sep 5 00:48:32 kernel: [*09/05/2018 00:48:32.9369] warning: device 'wired0' is down Sep 5 00:48:32 upgrade: Image verification failed. Sep 5 00:48:32 upgrade: Cleaning up tmp directory. Sep 5 00:48:33 kernel: [*09/05/2018 00:48:33.5167] Sep 5 00:48:33 kernel: [*09/05/2018 00:48:33.5167] Click sched monitor: schedulers = 1 Sep 5 00:48:36 upgrade: Image verification failed. Sep 5 00:48:36 upgrade: Cleaning up tmp directory. Sep 5 00:48:36 kernel: [*09/05/2018 00:48:36.5458] click-config/io-real.click:131: While initializing 'tohost_wired0 :: ToHost': Sep 5 00:48:36 kernel: [*09/05/2018 00:48:36.5458] warning: device 'wired0' is down Sep 5 00:48:36 kernel: [*09/05/2018 00:48:36.6157] ADDRCONF(NETDEV_UP): wired0: link is not ready Sep 5 00:48:36 kernel: [*09/05/2018 00:48:36.6157] ADDRCONF(NETDEV_UP): wired1: link is not ready Sep 5 00:48:37 kernel: [*09/05/2018 00:48:37.0656] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg40000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000 Sep 5 00:48:37 kernel: [*09/05/2018 00:48:37.0656] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg40000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000 Sep 5 00:48:37 brain: do_state:6325: assigning brain state: scan1; reason: initial_scan Sep 5 00:48:37 kernel: [*09/05/2018 00:48:37.3955] ADDRCONF(NETDEV_CHANGE): wired0: link becomes ready Sep 5 00:48:37 kernel: [*09/05/2018 00:48:37.4055] wired0: 1000 Mbps Full Duplex Sep 5 00:48:37 kernel: [*09/05/2018 00:48:37.4055] Sep 5 00:48:37 FIPS[3815]: *** lighttpd: FIPS Mode = disabled *** Sep 5 00:48:37 kernel: [*09/05/2018 00:48:37.7754] wired0: Link down Sep 5 00:48:37 kernel: [*09/05/2018 00:48:37.7754] Sep 5 00:48:38 kernel: [*09/05/2018 00:48:38.1653] chatter: tohost_srcr6 :: ToHost: device 'srcr6' went down Sep 5 00:48:38 kernel: [*09/05/2018 00:48:38.1853] chatter: tohost_srcr6 :: ToHost: device 'srcr6' came up Sep 5 00:48:38 kernel: [*09/05/2018 00:48:38.1952] ip6_port srcr6, ip6local fe80::dece:c1ff:fe20:1388, ip6 ::, plen 0, gw6 ::, gw6_mac 00:00:00:00:00:00, mtu 1500, vid 0, mode6 3(slaac) Sep 5 00:48:38 dnsmasq[2660]: exiting on receipt of SIGTERM Sep 5 00:48:38 dnsmasq[3864]: started, version 2.78 cachesize 150 Sep 5 00:48:38 dnsmasq[3864]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify Sep 5 00:48:38 dnsmasq[3864]: warning: using interface srcr2 instead Sep 5 00:48:38 dnsmasq[3864]: warning: using interface srcr2 instead Sep 5 00:48:38 dnsmasq[3864]: warning: using interface srcr2 instead Sep 5 00:48:38 dnsmasq[3864]: read /etc/hosts - 3 addresses Sep 5 00:48:38 brain: transitioning from init to scan1 Sep 5 00:48:38 brain: CDP PoE negotiation START Sep 5 00:48:39 kernel: [*09/05/2018 00:48:39.4049] wired0: 1000 Mbps Full Duplex Sep 5 00:48:39 kernel: [*09/05/2018 00:48:39.4049] Sep 5 00:48:40 brain: CDP PoE negotiation OK, Allocated power 24800 mWatt Requested power 24800 mWatt Sep 5 00:48:40 brain: Power mode: Full-Power, power_detection: DC_adapter(FALSE), 802.3AF_POE(TRUE) Sep 5 00:48:40 kernel: [*09/05/2018 00:48:40.5945] Sep 5 00:48:40 kernel: [*09/05/2018 00:48:40.5945] phy_value=0: org="0x1800" phy_reg="0x1000" Sep 5 00:48:47 kernel: [*09/05/2018 00:48:47.4624] Loading sha2... Sep 5 00:48:47 kernel: [*09/05/2018 00:48:47.4624] Dumpping sha1... Sep 5 00:48:49 kernel: [*09/05/2018 00:48:49.1519] Loading MIC cert and key Sep 5 00:48:49 kernel: [*09/05/2018 00:48:49.1519] Dumpping sha2... Sep 5 00:48:50 kernel: [*09/05/2018 00:48:50.8413] Loading MIC cert and key Sep 5 00:48:51 kernel: [*09/05/2018 00:48:51.2112] Generating key, this may take a while... Sep 5 00:48:53 kernel: [*09/05/2018 00:48:53.5105] Public key portion is: Sep 5 00:48:53 kernel: [*09/05/2018 00:48:53.5105] ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCYczbvjLrfmxmGYOA34gvzN283TynQ7oNyr2BbsJjPTJ82BWhSDvJH0bPJLsHfHTAnQvUgtbcUG1Hcx4qB4PKOi7mCZnC0h99hprcKdqaYfQbFsNbnGFFxVmUrv4cA/RFno6g5OKrrmvawlH0hdx6rQcC1QWgvqdxA Sep 5 00:48:53 kernel: [*09/05/2018 00:48:53.5105] Fingerprint: md5 1f:c3:5a:b2:8b:20:2f:bb:a3:22:44:e4:c3:0f:81:ed Sep 5 00:48:53 kernel: [*09/05/2018 00:48:53.5705] pid 3958's current affinity mask: 3 Sep 5 00:48:53 kernel: [*09/05/2018 00:48:53.5705] pid 3958's new affinity mask: 1 Sep 5 00:48:54 syslog: Password for 'admin' changed Sep 5 00:48:54 kernel: [*09/05/2018 00:48:54.0403] Password for 'admin' changed Sep 5 00:48:54 syslog: +gzip -dc /etc/wcp.usermodule.template.gz | sed -e 's/__TX_POWER_2G_FILE__/\/radio_fw\/R2.csv/g' -e 's/__TX_POWER_5G_FILE__/\/radio_fw\/R5.csv/g' -e 's/__EVM_POWER_2G_FILE__/\/radio_fw\/EVM_2.csv/g' -e 's/__EVM Sep 5 00:48:54 syslog: _POWER_5G_FILE__/\/radio_fw\/EVM_5.csv/g' -e 's/__DOMAIN_2G__/0/g' -e 's/__DOMAIN_5G__/48/g' -e 's/__PWR_TABLE_49G__/0/g' -e 's/__PRODUCT_ID__/AIR-AP1852I-Z-K9/g' -e 's/__AP_TYPE__/48/g' -e 's/__WIRELESS_MAC__/ Sep 5 00:48:54 syslog: DC:CE:C1:20:B4:80/g' -e 's/__WIRED_MAC__/DC:CE:C1:20:13:88/g' -e 's/__WIRED1_MAC__/DC:CE:C1:20:13:88/g' | DMALLOC_OPTIONS=debug=0x400003,inter=1000,log=/tmp/wcp.dmalloc.log,limit=40000000 wcpd & Sep 5 00:48:54 kernel: [*09/05/2018 00:48:54.1603] gzip -dc /etc/wcp.usermodule.template.gz | sed -e 's/__TX_POWER_2G_FILE__/\/radio_fw\/R2.csv/g' -e 's/__TX_POWER_5G_FILE__/\/radio_fw\/R5.csv/g' -e 's/__EVM_POWER_2G_FILE__/\/radio_fw\/EVM_2.csv/g' - Sep 5 00:48:54 FIPS[4011]: *** wcpd: FIPS Mode = disabled *** Sep 5 00:48:55 kernel: [*09/05/2018 00:48:55.5499] DOT11_DRV[0]: Init Radio0 Sep 5 00:48:55 kernel: [*09/05/2018 00:48:55.5699] DOT11_DRV[0]: Stop Radio0 Sep 5 00:48:55 kernel: [*09/05/2018 00:48:55.5799] DOT11_DRV[0]: set_channel Channel set to 6 Sep 5 00:48:55 kernel: [*09/05/2018 00:48:55.5899] DOT11_DRV[1]: Init Radio1 Sep 5 00:48:55 kernel: [*09/05/2018 00:48:55.6199] DOT11_DRV[1]: Stop Radio1 Sep 5 00:48:55 kernel: [*09/05/2018 00:48:55.6199] DOT11_DRV[1]: set_channel Channel set to 36 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.2597] DOT11_CFG[0] Radio Mode is changed from Local to FlexConnect Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.2597] DOT11_DRV[0]: Start Radio0 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.2696] DOT11_CFG[1] Radio Mode is changed from Local to FlexConnect Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.2696] DOT11_DRV[1]: Start Radio1 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.2896] DOT11_DRV[0]: Stop Radio0 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6595] DOT11_DRV[0]: set_channel Channel set to 1 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6595] DOT11_DRV[0]: Start Radio0 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6595] DOT11_DRV[0]: Channel set to 1, width 20 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6695] DOT11_DRV[0]: Stop Radio0 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6695] DOT11_DRV[0]: Start Radio0 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6695] DOT11_DRV[0]: Channel set to 1, width 20 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6795] DOT11_DRV[1]: Stop Radio1 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6995] DOT11_DRV[1]: set_channel Channel set to 52 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6995] DOT11_DRV[1]: Start Radio1 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.6995] DOT11_DRV[1]: Stop Radio1 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.7195] DOT11_DRV[1]: Start Radio1 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.7195] DOT11_DRV[1]: Channel set to 52, width 80 Sep 5 00:48:56 kernel: [*09/05/2018 00:48:56.7195] DOT11_DRV[1]: Stop Radio1 Sep 5 00:48:57 kernel: [*09/05/2018 00:48:57.0094] ol_if_dfs_enable: called Sep 5 00:48:57 kernel: [*09/05/2018 00:48:57.0194] DOT11_DRV[1]: Start Radio1 Sep 5 00:48:57 kernel: [*09/05/2018 00:48:57.0194] ol_if_dfs_enable: called Sep 5 00:48:57 kernel: [*09/05/2018 00:48:57.0194] DOT11_DRV[1]: Channel set to 52, width 80 Sep 5 00:49:01 kernel: [*09/05/2018 00:49:01.0482] Waiting for uplink IPv4 configuration Sep 5 00:49:06 kernel: [*09/05/2018 00:49:06.0566] Waiting for uplink IPv4 configuration Sep 5 00:49:06 brain: dhcpc succeeded on wired0 Sep 5 00:49:06 brain: do_state:6507: assigning brain state: gateway_check 0; reason: dhcp_on_wired0 Sep 5 00:49:06 dnsmasq[4060]: started, version 2.78 cachesize 150 Sep 5 00:49:06 dnsmasq[4060]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify Sep 5 00:49:06 brain: transitioning from scan1 to gateway_check 0 Sep 5 00:49:06 dnsmasq[4060]: using nameserver 172.20.13.241#53 Sep 5 00:49:06 dnsmasq[4060]: using nameserver 172.20.13.240#53 Sep 5 00:49:06 dnsmasq[4060]: read /etc/hosts - 3 addresses Sep 5 00:49:06 dnsmasq[4060]: exiting on receipt of SIGTERM Sep 5 00:49:07 dnsmasq[4066]: started, version 2.78 cachesize 150 Sep 5 00:49:07 dnsmasq[4066]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify Sep 5 00:49:07 brain: do_state:6415: assigning brain state: gateway_good 0; reason: internet and dns connectivity successful Sep 5 00:49:07 brain: transitioning from gateway_check 0 to gateway_good 0 Sep 5 00:49:07 brain: boot time: 45.320 seconds, 4067 processes spawned Sep 5 00:49:07 dnsmasq[4066]: using nameserver 172.20.13.241#53 Sep 5 00:49:07 dnsmasq[4066]: using nameserver 172.20.13.240#53 Sep 5 00:49:07 dnsmasq[4066]: read /etc/hosts - 3 addresses Sep 5 00:49:12 kernel: [*09/05/2018 00:49:06.8463] ethernet_port wired0, ip 172.16.113.21, netmask 255.255.255.0, gw 172.16.113.254, mtu 1500, bcast 172.16.113.255, dns1 172.20.13.240, dns2 172.20.13.241, domain cop.orgDOT11_CFG[0] Radio Mode is chang Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.1647] DOT11_CFG[1] Radio Mode is changed from FlexConnect to FlexConnect Sep 5 00:49:12 syslog: +/usr/bin/cisco_core.sh Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.2646] AP IPv4 Address updated from 0.0.0.0 to 172.16.113.21 Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] dtls_init: Use MIC device cert Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] dtls_init: Use MIC device cert private key Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] CAPWAP State: Init Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] PNP is not required, Starting CAPWAP discovery Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] CAPWAP State: Discovery Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] Got WLC address 0.172.20.14 from DHCP. Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3046] IP DNS query for CISCO-CAPWAP-CONTROLLER.cop.org Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3146] Discovery Request sent to 172.16.113.1, discovery type STATIC_CONFIG(1) Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3146] Discovery Request sent to 0.172.20.14, discovery type DHCP(2) Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3246] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0) Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3246] Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3246] CAPWAP State: Discovery Sep 5 00:49:12 kernel: [*09/05/2018 00:49:12.3246] Discovery Response from 172.16.113.1 Sep 5 00:50:55 kernel: [*09/05/2018 00:50:55.0000] Discovery Response from 172.16.113.1 Sep 5 00:50:55 kernel: [*09/05/2018 00:50:55.0000] Sep 5 00:50:55 kernel: [*09/05/2018 00:50:55.0000] CAPWAP State: DTLS Setup Sep 5 00:50:55 kernel: [*09/05/2018 00:50:55.2399] Sep 5 00:50:55 kernel: [*09/05/2018 00:50:55.2399] CAPWAP State: Join Sep 5 00:50:55 kernel: [*09/05/2018 00:50:55.2399] Sending Join request to 172.16.113.1 through port 5256 Sep 5 00:51:18 FIPS[4192]: *** shell: FIPS Mode = disabled *** Sep 5 00:51:30 kernel: [*09/05/2018 00:51:30.4589] srcr6: no IPv6 routers present Sep 5 00:51:52 kernel: [*09/05/2018 00:51:52.0222] Sep 5 00:51:52 kernel: [*09/05/2018 00:51:52.0222] CAPWAP State: DTLS Teardown Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.8907] Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.8907] CAPWAP State: Discovery Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.8907] Got WLC address 0.172.20.14 from DHCP. Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.8907] IP DNS query for CISCO-CAPWAP-CONTROLLER.cop.org Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.8907] Discovery Request sent to 172.16.113.1, discovery type STATIC_CONFIG(1) Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.9007] Discovery Request sent to 0.172.20.14, discovery type DHCP(2) Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.9007] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0) Sep 5 00:51:56 kernel: [*09/05/2018 00:51:56.9007] Discovery Response from 172.16.113.1 Sep 5 00:52:06 kernel: [*09/05/2018 00:52:06.0000] Discovery Response from 172.16.113.1 Sep 5 00:52:06 kernel: [*09/05/2018 00:52:06.0000] Sep 5 00:52:06 kernel: [*09/05/2018 00:52:06.0000] CAPWAP State: DTLS Setup Sep 5 00:52:06 kernel: [*09/05/2018 00:52:06.0699] Sep 5 00:52:06 kernel: [*09/05/2018 00:52:06.0699] CAPWAP State: Join Sep 5 00:52:06 kernel: [*09/05/2018 00:52:06.0699] Sending Join request to 172.16.113.1 through port 5256 Sep 5 00:53:03 kernel: [*09/05/2018 00:53:03.0222] Sep 5 00:53:03 kernel: [*09/05/2018 00:53:03.0222] CAPWAP State: DTLS Teardown Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8807] Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8807] CAPWAP State: Discovery Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8807] Got WLC address 0.172.20.14 from DHCP. Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8807] IP DNS query for CISCO-CAPWAP-CONTROLLER.cop.org Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8907] Discovery Request sent to 172.16.113.1, discovery type STATIC_CONFIG(1) Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8907] Discovery Request sent to 0.172.20.14, discovery type DHCP(2) Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8907] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0) Sep 5 00:53:07 kernel: [*09/05/2018 00:53:07.8907] Discovery Response from 172.16.113.1 Sep 5 00:53:17 kernel: [*09/05/2018 00:53:17.0000] Discovery Response from 172.16.113.1 Sep 5 00:53:17 kernel: [*09/05/2018 00:53:17.0000] Sep 5 00:53:17 kernel: [*09/05/2018 00:53:17.0000] CAPWAP State: DTLS Setup Sep 5 00:53:17 kernel: [*09/05/2018 00:53:17.0599] Sep 5 00:53:17 kernel: [*09/05/2018 00:53:17.0599] CAPWAP State: Join Sep 5 00:53:17 kernel: [*09/05/2018 00:53:17.0599] Sending Join request to 172.16.113.1 through port 5256 Sep 5 00:53:23 kernel: [*09/05/2018 00:53:23.2281] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Join(5). Sep 5 00:53:23 kernel: [*09/05/2018 00:53:23.2281] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Join(5). Sep 5 00:53:28 kernel: [*09/05/2018 00:53:28.1865] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Join(5). Sep 5 00:53:28 kernel: [*09/05/2018 00:53:28.2265] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Join(5). Sep 5 00:54:14 kernel: [*09/05/2018 00:54:14.0222] Sep 5 00:54:14 kernel: [*09/05/2018 00:54:14.0222] CAPWAP State: DTLS Teardown Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8807] Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8807] CAPWAP State: Discovery Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8807] Got WLC address 0.172.20.14 from DHCP. Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8807] IP DNS query for CISCO-CAPWAP-CONTROLLER.cop.org Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8907] Discovery Request sent to 172.16.113.1, discovery type STATIC_CONFIG(1) Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8907] Discovery Request sent to 0.172.20.14, discovery type DHCP(2) Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8907] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0) Sep 5 00:54:18 kernel: [*09/05/2018 00:54:18.8907] Discovery Response from 172.16.113.1 Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.0000] Discovery Response from 172.16.113.1 Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.0000] Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.0000] CAPWAP State: DTLS Setup Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.0699] Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.0699] CAPWAP State: Join Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.0699] Sending Join request to 172.16.113.1 through port 5256 Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.0799] Join Response from 172.16.113.1 Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.1699] nss_capwapmgr_enable_tunnel[1661]:c62d8000: tunnel 0 is already enabled Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.1899] Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.1899] CAPWAP State: Image Data Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.2499] do NO_UPGRADE, part1 is active part Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.2499] Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.2499] CAPWAP State: Configure Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.2499] DOT11_CFG[0] Radio Mode is changed from FlexConnect to FlexConnect Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.2499] DOT11_CFG[1] Radio Mode is changed from FlexConnect to FlexConnect Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.6698] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Configure(8). Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.6698] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Configure(8). Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.6698] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Configure(8). Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.6698] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Configure(8). Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.8197] Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.8197] CAPWAP State: Run Sep 5 00:54:29 kernel: [*09/05/2018 00:54:29.9697] AP has joined controller Sep 5 00:54:30 kernel: [*09/05/2018 00:54:29.9897] Flexconnect Switching to Connected Mode! Sep 5 00:56:32 kernel: [*09/05/2018 00:56:32.0000] FOUND CONFIGURED WLC (Primary) REDISCOVER TO CONNECT WITH THAT. Sep 5 00:56:32 kernel: [*09/05/2018 00:56:32.0000] Flexconnect Switching to Standalone Mode! Sep 5 00:56:32 kernel: [*09/05/2018 00:56:32.0000] Sep 5 00:56:32 kernel: [*09/05/2018 00:56:32.0000] CAPWAP State: DTLS Teardown Sep 5 00:56:36 kernel: [*09/05/2018 00:56:36.8385] Discovery Response from 172.16.113.1 Sep 5 00:56:37 kernel: [*09/05/2018 00:56:37.0000] Discovery Response from 172.16.113.1 Sep 5 00:56:37 kernel: [*09/05/2018 00:56:37.0000] Sep 5 00:56:37 kernel: [*09/05/2018 00:56:37.0000] CAPWAP State: DTLS Setup Sep 5 00:56:37 kernel: [*09/05/2018 00:56:37.0599] Sep 5 00:56:37 kernel: [*09/05/2018 00:56:37.0599] CAPWAP State: Join Sep 5 00:56:37 kernel: [*09/05/2018 00:56:37.0699] Sending Join request to 172.16.113.1 through port 5256 Depot-AP01# Depot-AP01#show flexconnect status Flexconnect Status: AP in Standalone Mode     If someone can please help me I'd appreciate it. Thanks. ... View more

Hi we have two sites each have two 4500X in a VSS. These sites are connected via layer 2 trunks. We currently only run IPv4 over these two sites.Now we have a need to configure a VLAN to support IPv6 multicasting which needs to have MLD enabled and ipv6 mld snooping querier. There is no need to provide IPv6 routing for the multicast traffic, it just needs to be able to be carried across the two sites within this VLAN for discovery. Can someone see below the commands I intend to use to get this to work: Switch(config)#ipv6 unicast-routing (Do I need this if we don't need to route IPv6 traffic) Switch(config)#ipv6 multicast-routing (Do I need this if we don't need to route the multicast traffic as it's only needed within one VLAN) Switch(config)#ipv6 mld snooping Switch(config)#ipv6 mld snooping vlan 25 Switch(config)#interface vlan 25 Switch(config-if)ipv6 address (Do I need to configure an IPv6 address at each site for this vlan interface?) Switch(config-if)#ipv6 mld snooping querier (Now this command I cannot get working as it's not available) What is the command to enable IPv6 MLD querier on a 4500X switch? If someone can have a look and point me in the right direction I'd appreciate it. Cheers, Ross. ... View more

Hi, I have a Cisco 5506X ASA with firepower fully licensed. I have URL filtering category Pornography/Adult any reputation set to block. Now some porn websites get blocked but some don't. When I'm in the ASDM looking at the monitoring of live connections I see the porn website that went through and it says its un-categorized. I went to the bright cloud url reputation website and it classifies this website as Pornography/Adult. So my question is why would the ASA be classifying this website us unknown? Any thoughts I'd appreciate it.    ... View more

Hi, We have a strange routing issue with summary routes and redistributed routes. Network topology is configured in a ring of nine switches. It appears that the manually configured summary addresses don't get propagated around the network. For example a summary address will only be propagated for 5 hops and then not any further the result being most of the switches only having one path of advertised for that summary. If a switch in the ring fails some of the switches become unavailable to each other based on hop count. We don't have any issues with connected routes being propagated around the network. The switches involved are 7 x Cisco  WS-C3850-24P and we have 2 x 4500X. We have only just recently upgraded the network from Cisco 3750 to 3850. Under the previous hardware we didn't have any of these issues using the same configuration.   Here's an example from one of the switch when we run show ip eigrp top 10.241.0.0/19:   #show ip eigrp top 10.241.0.0/19 EIGRP-IPv4 Topology Entry for AS(20)/ID(10.255.255.7) for 10.241.0.0/19   State is Passive, Query origin flag is 1, 1 Successor(s), FD is 3584   Descriptor Blocks:   10.255.0.13 (Port-channel1), from 10.255.0.13, Send flag is 0x0       Composite metric is (3584/3328), route is Internal       Vector metric:         Minimum bandwidth is 1000000 Kbit         Total delay is 40 microseconds         Reliability is 255/255         Load is 1/255         Minimum MTU is 1500         Hop count is 3         Originating router is 10.255.255.4   The summary for 10.241.0.0/19 is only 3 hops away which it shows but this switch should be showing another path to this summary route which is 6 hops away but its not. If I run the same command on the next switch in the loop it shows both paths to the summary as shown below: show ip eigrp top 1.241.0.0/19 EIGRP-IPv4 Topology Entry for AS(20)/ID(10.255.255.8) %Entry 1.241.0.0/19 not in topology table CON-CP11-SW01#show ip eigrp top 10.241.0.0/19 EIGRP-IPv4 Topology Entry for AS(20)/ID(10.255.255.8) for 10.241.0.0/19   State is Passive, Query origin flag is 1, 1 Successor(s), FD is 3840   Descriptor Blocks:   10.255.0.18 (Port-channel1), from 10.255.0.18, Send flag is 0x0       Composite metric is (3840/3584), route is Internal       Vector metric:         Minimum bandwidth is 1000000 Kbit         Total delay is 50 microseconds         Reliability is 255/255         Load is 1/255         Minimum MTU is 1500         Hop count is 4         Originating router is 10.255.255.4   10.255.0.21 (Port-channel2), from 10.255.0.21, Send flag is 0x0       Composite metric is (4096/3840), route is Internal       Vector metric:         Minimum bandwidth is 1000000 Kbit         Total delay is 60 microseconds         Reliability is 255/255         Load is 1/255         Minimum MTU is 1500         Hop count is 5   The switches are all running the same IOS XE version 03.03.03SE. Can someone let me know if this is a bug or something else?   Thanks, Ross. ... View more

Hi,   I have a Cisco 867vae 15.3 advanced security IOS and was wondering if it supports Anyconnect?   I'm trying to set it up so I can connect via the Anyconnect windows client. Does anyone have a working config or point me in the right direction?   Thanks, Ross ... View more

Hi Guys,   We have two Cisco 5525X ASA firewalls and they are in a Active/Standby failover cluster. At the moment each ASA is using Gig 0/3 plugged into a 6509 switch as part of the failover link. Each ASA are at different data centres. I need to add another physical interface Gig 0/4 in the ASA's and have this part of the failover between the existing Gig 0/3 interface. I have been reading about configuring redundant links and adding the two physical interfaces as part of a redundant group. Can someone let me know how to configure two physical interface as a redundant group and have them part of the failover between two ASA's?   See below existing config for our failover: Primary ASA failover failover lan unit primary failover lan interface failover GigabitEthernet0/3 failover mac address GigabitEthernet0/0 001b.54f7.1a2b 001b.54f7.2a2b failover mac address GigabitEthernet1/0 001b.54f7.3a2d 001b.54f7.4a2d failover mac address GigabitEthernet1/1 001b.54f7.4a2e 001b.54f7.5a2e failover link failover GigabitEthernet0/3 failover interface ip failover 10.10.10.1 255.255.255.252 standby 10.10.10.2   Secondary ASA   failover failover lan unit secondary failover lan interface failover GigabitEthernet0/3 failover mac address GigabitEthernet0/0 001b.54f7.1a2b 001b.54f7.2a2b failover mac address GigabitEthernet1/0 001b.54f7.3a2d 001b.54f7.4a2d failover mac address GigabitEthernet1/1 001b.54f7.4a2e 001b.54f7.5a2e failover link failover GigabitEthernet0/3 failover interface ip failover 10.10.10.1 255.255.255.252 standby 10.10.10.2   Cheers, Ross. ... View more

Hi Guys, I upgrade our old Cisco 5520 ASA's with 2 new Cisco 5525X ASA on the weekend. On our old 5520's we used a CWDM sfp for our failover and worked no problem. But with the new 5525X it doesn't detect any of the CWDM sfp's. Can someone let me know if the new 5525X supports CWDM sfp's? Thanks, Ross. ... View more