Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About scottsassin
03-01-2019
scottsassin
Beginner
I have been a Network Engineer for the past 10 years. I presently work as a network engineer, for an organization in the healthcare industry. I am located in Anchorage Alaska.
Recent Badges
Stats
Member since
04-01-2009
116
Posts
5
Helpful
1
Solution
02-28-2019
03:30 PM
We are deploying a wireless voice badge system. We need to enable PIM sparse mode.
I need to know how to enable PIM sparse mode. The feature is not enabled now. Can I enable the feature, during production, without causing any outages?
Thanks,
Scott
... View more
Labels:
01-17-2019
03:26 PM
I wish to upgrade the IOS software from 03.08.05.E to 3.08.07. Please let me know the procedure to do this. I can't find instructions anywhere on the Cisco site.
... View more
Labels:
06-12-2018
10:49 AM
We are implementing a Click-to-Accept web page for our guests. We have certain devices that need to bypass the Click-to-Accept page, and be authenticated by just joining the WLAN.
Is there any way to configure an address or subnet, to be exempt from the Click-to-Accept page, on a WLAN?
... View more
Labels:
04-11-2018
05:10 PM
I found the answer. I had to disable 4 of the 8 10gig SFP ports on the sup. That did it.
... View more
04-11-2018
02:21 PM
We are using a 4510R+E chassis with 4648-RJ45V+E Blades. Table 2 doesn't apply.
... View more
04-11-2018
12:37 PM
We have decided not do to redundant supervisors in this switch. I have upgraded the IOS of the SUP8-E to 3.6.8. The tenth slot still says unsupported. All the documentation says that all ports can be used for the 4648 blade. Why does it still say unsupported?
... View more
04-10-2018
03:56 PM
Do I need to upgrade to the latest XO code, or can I go to a different one?
... View more
04-10-2018
02:20 PM
1. sh version;
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500es8-UNIVERSALK9-M), Version 03.03.00.XO RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Wed 14-Aug-13 07:26 by prod_rel_team Cisco IOS-XE software, Copyright (c) 2005-2013 by cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. ROM: 15.1(1r)SG4 Switch uptime is 22 minutes Uptime for this control processor is 24 minutes System returned to ROM by power-on Running default software Jawa Revision 3, RadTrooper Revision 0x0.0x41, Conan Revision 0x1449 !
License Information for 'WS-X45-SUP8-E' License Level: lanbase Type: Default. No valid license found. Next reboot license Level: lanbase cisco WS-C4510R+E (P5040) processor (revision 2) with 4194304K bytes of physical memory. Processor board ID FXS2031Q3UN P5040 CPU at 2.2GHz, Supervisor 8-E Last reset from PowerUp 1 Virtual Ethernet interface 144 Gigabit Ethernet interfaces 16 Ten Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2101
2. sh module;
Chassis Type : WS-C4510R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+------------------+----------- 5 8 Sup 8-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP8-E CAT1822L1PG 6 8 Sup 8-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP8-E CAT1822L1RL 7 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E JAE15030HUT 8 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E JAE1749093V 9 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E JAE181306G9 10 0 Unsupported module WS-X4648-RJ45V+E JAE17400H72
M MAC addresses Hw Fw Sw Status --+--------------------------------+---+------------+----------------+--------- 5 0081.c4a1.a280 to 0081.c4a1.a287 1.1 15.1(1r)SG4 03.03.00.XO Ok 6 0081.c4a1.a288 to 0081.c4a1.a28f 1.1 15.1(1r)SG4 03.03.00.XO Ok 7 c471.fe8d.1700 to c471.fe8d.172f 2.0 Ok 8 24e9.b3b3.09f0 to 24e9.b3b3.0a1f 3.1 Ok 9 24e9.b3e6.3c0c to 24e9.b3e6.3c3b 3.1 Ok 10 7081.0537.dd90 to 7081.0537.ddbf 3.1 Unsupport
Mod Redundancy role Operating mode Redundancy status ----+-------------------+-------------------+---------------------------------- 5 Standby Supervisor RPR Standby cold 6 Active Supervisor RPR Active
Switch#
3. sh logs.
Apr 10 20:53:39.599: %C4K_IOSSYS-6-IMAGELEVEL: Supervisor booting in image level 'lanbase' *Apr 10 20:53:39.712: %C4K_REDUNDANCY-6-INIT: Initializing as ACTIVE supervisor *Apr 10 20:54:01.979: %C4K_REDUNDANCY-6-DUPLEX_MODE: The peer Supervisor has been detected *Apr 10 20:54:24.752: %C4K_CHASSIS-3-LINECARDNOTVALIDINSLOT: Module WS-X4648-RJ45V+E is not supported in slot 10, try slots 1, 2, 3, 4, 7, 8, 9. *Apr 10 20:55:09.705: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan *Apr 10 20:55:10.999: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X45-SUP8-E S/N: CAT1822L1RL Hw: 1.1) is online *Apr 10 20:55:10.999: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 7 (WS-X4648-RJ45V+E S/N: JAE15030HUT Hw: 2.0) is online *Apr 10 20:55:10.999: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 8 (WS-X4648-RJ45V+E S/N: JAE1749093V Hw: 3.1) is online *Apr 10 20:55:10.999: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 9 (WS-X4648-RJ45V+E S/N: JAE181306G9 Hw: 3.1) is online *Apr 10 20:53:26.078: %LICENSE-6-LICENSE_LEVEL: Module name = WS-X45-SUP8-E Next reboot level = lanbase and License = No license needed *Apr 10 20:55:13.453: %SYS-5-CONFIG_I: Configured from memory by console *Apr 10 20:55:13.687: %SYS-5-RESTART: System restarted -- Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500es8-UNIVERSALK9-M), Version 03.03.00.XO RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Wed 14-Aug-13 07:26 by prod_rel_team *Apr 10 20:55:13.710: %SSH-5-ENABLED: SSH 1.99 has been enabled *Apr 10 20:55:21.583: %C4K_REDUNDANCY-6-MODE: ACTIVE supervisor initializing for hsa mode *Apr 10 20:55:24.585: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 5 (WS-X45-SUP8-E S/N: CAT1822L1PG Hw: 1.1) is online *Apr 10 20:55:24.640: %C4K_REDUNDANCY-6-MODE: ACTIVE supervisor initializing for rpr mode *Apr 10 20:55:25.627: %C4K_REDUNDANCY-3-COMMUNICATION: Communication with the peer Supervisor has been established *Apr 10 20:55:28.033: %C4K_REDUNDANCY-5-CONFIGSYNC: The bootvar has been successfully synchronized to the standby supervisor *Apr 10 20:55:28.033: %C4K_REDUNDANCY-5-CONFIGSYNC: The config-reg has been successfully synchronized to the standby supervisor *Apr 10 20:55:28.035: %C4K_REDUNDANCY-5-CALENDAR: The calendar has been successfully synchronized to the standby supervisor for the first time *Apr 10 20:55:28.035: %C4K_REDUNDANCY-5-CONFIGSYNC: The startup-config has been successfully synchronized to the standby supervisor *Apr 10 20:55:28.536: %C4K_REDUNDANCY-5-CONFIGSYNC: The private-config has been successfully synchronized to the standby supervisor *Apr 10 20:55:29.853: %RF-5-RF_TERMINAL_STATE: 6 ha_mgr: Terminal state reached for (RPR) *Apr 10 21:08:32.470: %C4K_IOSMODPORTMAN-6-MODULEREMOVED: Module 10 is removed *Apr 10 21:08:50.360: %C4K_CHASSIS-3-LINECARDNOTVALIDINSLOT: Module WS-X4648-RJ45V+E is not supported in slot 10, try slots 1, 2, 3, 4, 7, 8, 9.
... View more
04-09-2018
03:59 PM
We just purchased a 4510R+E with dual supervisors 8-E.
When we insert one WS-X4648-RJ45V+E blade in the 10th slot, it says Unsupported.
Can I have 8 of these blades in the above configuration?
Thanks,
Scott
... View more
Labels:
03-12-2018
01:45 PM
N7K-1 (Connected) interface Ethernet4/4 description AA-03 switchport switchport mode trunk switchport trunk native vlan 996 switchport trunk allowed vlan 1,25-28,50-64,123,223,802,989,994 switchport trunk allowed vlan add 996 channel-group 163 mode active no shutdown N7K-2 (Doesn't Connect) interface Ethernet4/4 description AA-03 switchport switchport mode trunk switchport trunk native vlan 996 switchport trunk allowed vlan 1,25-28,50-64,123,223,802,989,994 switchport trunk allowed vlan add 996 channel-group 163 mode active no shutdown AA-03 interface Port-channel1 switchport trunk native vlan 996 switchport mode trunk end interface TenGigabitEthernet1/0/1 switchport trunk native vlan 996 switchport mode trunk channel-group 1 mode passive end interface TenGigabitEthernet1/0/2 switchport trunk native vlan 996 switchport mode trunk channel-group 1 mode passive end
... View more
03-12-2018
01:32 PM
N7K-1 (The one that connects) interface port-channel163 description vPC to AA03-TC30 switchport switchport mode trunk switchport trunk native vlan 996 switchport trunk allowed vlan 1,25-28,50-64,123,223,802,989,994 switchport trunk allowed vlan add 996 vpc 163 port-channel163 Ethernet4/4 82857 89290 0 0 0 N7K-2 (The one that doesn't connect) interface port-channel163 description vPC to AA03-TC30 switchport switchport mode trunk switchport trunk native vlan 996 switchport trunk allowed vlan 1,25-28,50-64,123,223,802,989,994 switchport trunk allowed vlan add 996 vpc 163 no lacp in list
... View more
03-12-2018
01:13 PM
We have a pair if Nexus 7k's, c7010s, running version 6.2(12). The inventory is as follows:
Mod Ports Module-Type Model Status --- ----- ----------------------------------- ------------------ ---------- 1 48 1000 Mbps Optical Ethernet Module N7K-M148GS-11 ok 2 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok 3 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok 4 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok 5 0 Supervisor Module-1X N7K-SUP1 active * 6 0 Supervisor Module-1X N7K-SUP1 ha-standby 7 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok 8 32 1/10 Gbps Ethernet Module N7K-F132XP-15 ok 9 32 1/10 Gbps Ethernet Module N7K-F132XP-15 ok
The fiber is single mode. The transceiver is a SFP-10GBase-LRM on both sides. When we try to setup a new port-channel, it doesn't establish. We have determined that it is not cable fiber related.
Please let us know if there is any known issue with port-channels on N7k's or where we should search for a solution.
... View more
Labels:
03-06-2018
04:17 PM
I have recently upgraded our routers from 2811 to 4321 series. Both running advanced IP services.
I can't seem to get IP cache flow working on the interfaces. The configuration I had on the 2811 was ip cache flow egress/ingress. The 4321 doesn't have this command.
I really need to do a show ip cache flow, to see traffic entering or leaving an interface.
Thanks,
Scott
... View more
Labels:
12-21-2017
03:28 PM
I have a stack of C9300 switches. I am trying to configure tacacs+ authentication. I read the documentation, and I'm getting no where .
Please post an example of aaa configuration, using a group of tacacs servers.
... View more
Labels:
Created by
scottsassin
in Cisco Bug Discussions
in Cisco Bug Discussions
11-22-2017
02:22 PM
11-22-2017
02:22 PM
I was able to recover an access point from this bug. I performed a reset on the access point by pressing the button for 18 seconds while re-powering the access point. The access point then rebooted, joined the controller, and downloaded it's IOS.
... View more
Labels:
02-28-2019
We are deploying a wireless voice badge system. We need to enable PIM
sparse mode. I need to know ho...
01-17-2019
I wish to upgrade the IOS software from 03.08.05.E to 3.08.07. Please
let me know the procedure to d...
Created by
scottsassin
in Switching
06-12-2018
06-12-2018
We are implementing a Click-to-Accept web page for our guests. We have
certain devices that need to ...
Created by
scottsassin
in Switching
04-11-2018
04-11-2018
I found the answer. I had to disable 4 of the 8 10gig SFP ports on the
sup. That did it.
Created by
scottsassin
in Switching
04-11-2018
04-11-2018
We are using a 4510R+E chassis with 4648-RJ45V+E Blades. Table 2 doesn't
apply.
Created by
scottsassin
in Switching
04-11-2018
04-11-2018
We have decided not do to redundant supervisors in this switch. I have
upgraded the IOS of the SUP8-...
Created by
scottsassin
in Switching
04-10-2018
04-10-2018
Do I need to upgrade to the latest XO code, or can I go to a different
one?
Created by
scottsassin
in Switching
04-10-2018
04-10-2018
1. sh version; Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3
Switch Software (cat4500es8-UNI...
Created by
scottsassin
in Switching
04-09-2018
04-09-2018
We just purchased a 4510R+E with dual supervisors 8-E. When we insert
one WS-X4648-RJ45V+E blade in ...
Created by
scottsassin
in Switching
03-12-2018
03-12-2018
N7K-1 (Connected)interface Ethernet4/4 description AA-03 switchport
switchport mode trunk switchport...
Created by
scottsassin
in Switching
03-12-2018
03-12-2018
N7K-1 (The one that connects)interface port-channel163 description vPC
to AA03-TC30 switchport switc...
Created by
scottsassin
in Switching
03-12-2018
03-12-2018
We have a pair if Nexus 7k's, c7010s, running version 6.2(12). The
inventory is as follows: Mod Port...
03-06-2018
I have recently upgraded our routers from 2811 to 4321 series. Both
running advanced IP services. I ...
12-21-2017
I have a stack of C9300 switches. I am trying to configure tacacs+
authentication. I read the docume...
Public Statistics
| Date Registered | 04-01-2009 01:51 PM |
| Date Last Visited | 03-01-2019 02:02 AM |
| Total Messages Posted | 116 |
| Total Helpful Votes Received | 5 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
.jpg "VIP Expert"){kind=icon}
