Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Dan Loring
08-18-2017
Stats
Member since
02-09-2011
124
Posts
10
Helpful
0
Solutions
03-28-2014
03:12 AM
So I have a remote office connected via an MPLS. I am adding a broadband connection to this site as well and want all port 80 and 443 traffic routed out the Broabband connection. The mpls is serial0/0/0(55.55.55.55/30) and the broadband is connected to fastethernet0/2(44.44.44.44/30) What routes would I need to configure this?
... View more
Labels:
Created by
Dan Loring
in VPN and AnyConnect
in VPN and AnyConnect
10-10-2013
12:31 PM
10-10-2013
12:31 PM
Sounds good Rick, one final question. Will this fail back to the VPN when that comes back up? Does the IP SLA continue pinging and when the destination IP comes back up does it re-adjust the routes? Thanks again, Dan
... View more
Created by
Dan Loring
in VPN and AnyConnect
in VPN and AnyConnect
10-10-2013
09:37 AM
10-10-2013
09:37 AM
Thanks Rick, We are currently running static routes over the MPLS, but I am not against ospf or eigrp, I know we could do it with the MPLS as the Primary, but the issue we are running into is we want the MPLS as the secondary route and the broadband VPN Tunnel as the primary. I will look into the IP SLA/track.. Dan
... View more
Created by
Dan Loring
in VPN and AnyConnect
in VPN and AnyConnect
10-09-2013
11:36 AM
10-09-2013
11:36 AM
We currently have a 1.5 mb MPLS connection to a remote site. Also at this site we have a 20 mb broadband connection. We want to create a VPN tunnel over the broadband connection back to our primary location and make the mpls a secondary line and have it fail over if the VPN tunnel goes down. we have purchased a new 1900 series router withthe VPN and Security bundle. I am know being told by our VAR that this cannot be done?? Has anyone scene a vpn tunnel failover to an mpls before?
... View more
Labels:
Created by
Dan Loring
in Application Networking
in Application Networking
08-23-2013
04:58 AM
08-23-2013
04:58 AM
Thanks for the assistance! Cheers, Dan
... View more
Created by
Dan Loring
in Application Networking
in Application Networking
08-02-2013
09:31 AM
08-02-2013
09:31 AM
A while back I started upgrading some of our WAAS 274/574 devices and once I got halfway through I relized I was on the wrong path to get the devices to accelerate and compress Native ICA for our Citrix sessions. So Currently I have half our devices at 4.3.3c and the other half at 4.4.7 So my questions are.... What is the latest greatest version that I should be at for Native ICA Acceleration? What is the best upgrade/downgrade path I should take to get there?
... View more
06-14-2013
06:22 AM
class-map match-any af41 match access-group name QOS_AF41 class-map match-any ef ! ! policy-map 25_74 class ef bandwidth percent 25 set ip dscp ef class af41 bandwidth percent 74 set ip dscp af41 class class-default fair-queue set ip dscp default interface FastEthernet0/3/0 ip address 192.10.200.2 255.255.255.0 ip wccp 62 redirect in duplex auto speed auto no cdp enable max-reserved-bandwidth 100 service-policy output 25_74 ip access-list extended QOS_AF41 permit tcp any eq 3389 any permit ip host 192.10.100.80 any permit ip host 192.10.100.70 any permit ip host 192.10.100.66 any class-map match-any af41 match access-group name QOS_AF41 class-map match-any ef
... View more
06-14-2013
06:14 AM
So even if the circuit is full it will still show 0 bits?? I just pushed a huge file to all our remote locations to see if I could get any traffic on that ef que, and it is still showing 0 bits.... KamcoMPLS#show policy-map interface output FastEthernet0/3/0 Service-policy output: 25_74 Class-map: ef (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: none 0 packets, 0 bytes 5 minute rate 0 bps Queueing Output Queue: Conversation 265 Bandwidth 25 (%) Bandwidth 25000 (kbps)Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 QoS Set dscp ef Packets marked 0 Class-map: af41 (match-any) 55198316 packets, 8141538565 bytes 5 minute offered rate 69000 bps, drop rate 0 bps Match: access-group name QOS_AF41 55198316 packets, 8141538811 bytes 5 minute rate 69000 bps Queueing Output Queue: Conversation 266 Bandwidth 74 (%) Bandwidth 74000 (kbps)Max Threshold 64 (packets) (pkts matched/bytes matched) 341/36959 (depth/total drops/no-buffer drops) 0/0/0 QoS Set dscp af41 Packets marked 55198291 Class-map: class-default (match-any) 216007783 packets, 122336393528 bytes 5 minute offered rate 8973000 bps, drop rate 0 bps Match: any Queueing Flow Based Fair Queueing Maximum Number of Hashed Queues 256 (total queued/total drops/no-buffer drops) 0/0/0 QoS Set dscp default Packets marked 215804777 KamcoMPLS#
... View more
06-13-2013
01:22 PM
We have QOS over our MPLS and my provider says that our QOS policies are working fine, but when I run the show policy-map interface command it always shows the EF que with 0 packets and using up 25% of our bandwidth. We are not tagging anything in the EF que we do not run any time sensitive protocols(voip video) over the MPLS. All I want to do is remove QOS entirely, but my provider is balking at the idea. Why would I keep this policy that is wasting 25% of my bandwidth??? show policy-map interface FastEthernet0/3/0 Service-policy output: 25_74 Class-map: ef (match-any) 0 packets, 0 bytes 5 minute offered rate 0 bps, drop rate 0 bps Match: none 0 packets, 0 bytes 5 minute rate 0 bps Queueing Output Queue: Conversation 265 Bandwidth 25 (%) Bandwidth 25000 (kbps)Max Threshold 64 (packets) (pkts matched/bytes matched) 0/0 (depth/total drops/no-buffer drops) 0/0/0 QoS Set dscp ef Packets marked 0 Class-map: af41 (match-any) 47909379 packets, 7006127169 bytes 5 minute offered rate 82000 bps, drop rate 0 bps Match: access-group name QOS_AF41 47909379 packets, 7006127415 bytes 5 minute rate 82000 bps Queueing Output Queue: Conversation 266 Bandwidth 74 (%) Bandwidth 74000 (kbps)Max Threshold 64 (packets) (pkts matched/bytes matched) 297/30848 (depth/total drops/no-buffer drops) 0/0/0 QoS Set dscp af41 Packets marked 47909354
... View more
- Tags:
- 2900_routers
- mpls
- qos
Labels:
Created by
Dan Loring
in Application Networking
in Application Networking
11-20-2012
01:02 PM
11-20-2012
01:02 PM
Ok, I got the correct version of vnc, tightVNC works. Now It seems my server image is corrupt, and I need to build a new server. All the documentation I see says that an iso comes factory installed on the device called WOW66.iso. I am not seeing this image to restart the server build. Any idea where to download this? Any idea where to find wae# copy cdrom wow-recovery / WoW_RECOVERY I did not set this up and do not have the disk.
... View more
Created by
Dan Loring
in Application Networking
in Application Networking
11-20-2012
09:49 AM
11-20-2012
09:49 AM
I have got the new hardware in place, and it is back up and running except for the virtual blade. I had ftp'ed the blade a few monthes back to our ftp server, but we cannot get it back up and running. So I am thinking it is corrupt. How do I go about building a new server on this device? Do I just put an iso of the the 2008 setup disk in and create it there? I am more of a vmware person. Can I create the server on vmware and convert the vmdk file to an iso file and then just ftp it to the local1/vbs directory? What version of vnc do I need to connect to the server once it is there and built, I am using enterprise edition E4.5.4(r41964)
... View more
11-12-2012
11:12 AM
I have a vpn connection to a remote site, evidently it turns out that IP is dynamic. So Every 6 months there ip changes. I know we should have a static IP. So the last time this happened I removed the old IP address and put in the new one on the ASA on our end: config t no crypto map mymap 1 set peer 72.95.xx.xx crypto map mymap 1 set peer 72.65.xx.xx The technician who previousely worked on this, and is in the woods hunting, said that he also re-applied the myset crypto map on outside interface. Does anyone know what I need to do to to re-apply the myset crypto map on the outside interface??
... View more
Labels:
08-30-2012
10:21 AM
We are in the process of upgrading our AD to 2008. So we are building a new Schema Master Grand Pooba AD server with a new IP address, the old address will be demoted. Unfortunately we have our AAA Server Group using radius to authenticate off this old server for our VPN users. I went to Configuration > Remote Access VPN > AAA/Local Users > AAA Server Groups > AuthInBound on the ASA5510 ASDM ver(6.4(9)) and went to add our new AD Server as the AAA server for VPN and it is asking for a server secret key and Common password?? Anyone know where we go to generate this server secret key and a common password?? Thanks, Dan
... View more
Labels:
08-29-2012
06:41 AM
We recently went from 2003 DHCP server to 2008. In 2003 the server relay agent broadcast dhcp requests accros our subnets, but with 2008 only our primary subnet is receiving addresses. So we have our main location at 192.10.10.0, and we have have 7 remote sites accross our MPLS that each have there own subnet 192.10.20.0, 192.10.30, 192.10.30.0.....and so on. The majority of our remote sites have dhcp servers, but 2 of the sites get there scope from our main DHCP server. So lets say 192.10.40.0 and 192.10.50.0 need there dhcp requests sent to them from our primary DHCP server with the IP of 192.10.10.27. There are two routers that sit between each site(see attached diagram) Would I just need to put the command for IP-Helper address 192.10.10.27 on the interface S0 on the 2800 router, or would I need to add that command to the E0 interfaces on the 1841 routers as well, or any subnet that I wanted to broadcast dhcp requests?? Any help wouyld be great. Thanks, Dan
... View more
Labels:
03-28-2014
So I have a remote office connected via an MPLS. I am adding a broadband
connection to this site as ...
10-10-2013
Sounds good Rick, one final question. Will this fail back to the VPN
when that comes back up? Does t...
10-10-2013
Thanks Rick,We are currently running static routes over the MPLS, but I
am not against ospf or eigrp...
10-09-2013
We currently have a 1.5 mb MPLS connection to a remote site. Also at
this site we have a 20 mb broad...
08-02-2013
A while back I started upgrading some of our WAAS 274/574 devices and
once I got halfway through I r...
06-14-2013
class-map match-any af41 match access-group name QOS_AF41class-map
match-any ef!!policy-map 25_74 cl...
06-14-2013
So even if the circuit is full it will still show 0 bits?? I just pushed
a huge file to all our remo...
06-13-2013
We have QOS over our MPLS and my provider says that our QOS policies are
working fine, but when I ru...
Created by
Dan Loring
in Application Networking
11-20-2012
11-20-2012
Ok, I got the correct version of vnc, tightVNC works. Now It seems my
server image is corrupt, and I...
Created by
Dan Loring
in Application Networking
11-20-2012
11-20-2012
I have got the new hardware in place, and it is back up and running
except for the virtual blade. I ...
11-12-2012
I have a vpn connection to a remote site, evidently it turns out that IP
is dynamic. So Every 6 mont...
08-30-2012
We are in the process of upgrading our AD to 2008. So we are building a
new Schema Master Grand Poob...
Public Statistics
| Date Registered | 02-09-2011 12:46 PM |
| Date Last Visited | 08-18-2017 04:01 AM |
| Total Messages Posted | 124 |
| Total Helpful Votes Received | 10 |
.jpg "Hall of Fame Guru"){kind=icon}
