Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About lachlanpeters
Stats
Member since
04-07-2010
16
Posts
0
Helpful
0
Solutions
Created by
lachlanpeters
in IP Telephony and Phones
in IP Telephony and Phones
03-06-2013
01:17 AM
03-06-2013
01:17 AM
Hi, I have tried that debug image too, as Danny mentioned, it did fix the problem. (love all the debug output that cant be turned off) More recently Cisco asked if I could test with a 'alpha' release. Everything is working. So I think it is more that cisco must be waiting on other stuff to put in the release other then just this fix. Lachlan
... View more
Created by
lachlanpeters
in IP Telephony and Phones
in IP Telephony and Phones
01-01-2013
09:33 PM
01-01-2013
09:33 PM
Hi, Cisco has advised me that the fix for this problem is due in March 2013. Also I have request that some snmp stuff be added to allow sip-ua registration monitoring Enhancement Request ID is CSCud86617
... View more
Created by
lachlanpeters
in IP Telephony and Phones
in IP Telephony and Phones
11-27-2012
05:09 AM
11-27-2012
05:09 AM
Hi, Just wondering about the Bug ID, we are having the same problem.
... View more
02-14-2012
02:40 PM
I have been searching and reading threads for the last 8 days. I was thinking that I would finely start a thread to get some specifics help. Thankyou for the help
... View more
02-13-2012
02:06 PM
I have try some off - https://supportforums.cisco.com/message/1166213#1166213 Is there a resource to ffind the correct one?
... View more
02-12-2012
10:29 PM
Hi, We are currenlty having a problem with 2821 with a 4fxo not tell the PSTN ( Telstra ) that the call has end. IP Phone <--- 2821 <---PSTN<---- Phone B If the IP Phone hungup first, on a PSTN originated call, the PSTN network will not see the hangup. If you listen to the phone line the call is still active and connected to phone b. IP Phone ---> 2821 ---> PSTN----> Phone B But if it is a IP Phone originated call the hungup works ok. The 2821 is config with mgcp. I have looked at http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800ae2d1.shtml But we are still having problems. eg config voice-port 0/2/2 trunk-group VOICE-T echo-cancel coverage 64 cptone AU timing hookflash-out 50 impedance complex1
... View more
Labels:
06-22-2011
05:48 PM
You are correct. The are just sitting a a room doing nothing. I can get basis config on them via the switch looking for it ( tftp and naming the config "network-config") I have not been able to find away for them to update the IOS. Thankyou for you help
... View more
06-20-2011
10:10 PM
Hi, Just wondering if there is an easer way to update 100+ 2960 switches, apart from pasting the commands in via console. They are not connected to any network and have the default config. They boot and look for a config. Lachlan
... View more
Labels:
Created by
lachlanpeters
in Other Collaboration Subjects
in Other Collaboration Subjects
03-21-2011
05:26 PM
03-21-2011
05:26 PM
Hi, Can are need to condense the number of VG224 we have. Is there any easy way to check if a phone is connected to the unit, or stats on usage on the voice ports.
... View more
Labels:
Created by
lachlanpeters
in Policy and Access
in Policy and Access
06-30-2010
09:03 PM
06-30-2010
09:03 PM
It is on a switch ( 2960, 3560 and 3750. All IOS at most 1 year old) I am looking basically if anyone enters "monitor session........" a syslog event is triggered Lachlan
... View more
Created by
lachlanpeters
in Policy and Access
in Policy and Access
06-20-2010
11:59 PM
06-20-2010
11:59 PM
Hi All, I am needing to find away to monitor if a monitor sessions is created/deleted or change. Is there anyway that you know of to see that detail
... View more
- Tags:
- aaa
Labels:
04-19-2010
04:34 AM
No Windows Firewall and I have removed Symentec Endpoint which has a "firewall" in it. jrm is still not starting.
... View more
04-18-2010
06:29 PM
JRM is stuck initialize. pdhsow below for jrm and attached is a full pdshow and jrm log with some error in it. Process= jrm State = Waiting to initialize. Pid = 13844 RC = 0 Signo = 0 Start = 19/04/2010 10:28:56 AM Stop = Not applicable Core = Not applicable Info = Application dependency start: application(s) depending on it.
... View more
Labels:
03-06-2013
Hi,I have tried that debug image too, as Danny mentioned, it did fix the
problem.(love all the debug...
01-01-2013
Hi,Cisco has advised me that the fix for this problem is due in March
2013.Also I have request that ...
02-14-2012
I have been searching and reading threads for the last 8 days. I was
thinking that I would finely st...
02-13-2012
I have try some off
-https://supportforums.cisco.com/message/1166213#1166213Is there a
resource to f...
02-12-2012
Hi,We are currenlty having a problem with 2821 with a 4fxo not tell the
PSTN ( Telstra ) that the ca...
06-22-2011
You are correct. The are just sitting a a room doing nothing.I can get
basis config on them via the ...
06-20-2011
Hi,Just wondering if there is an easer way to update 100+ 2960 switches,
apart from pasting the comm...
Created by
lachlanpeters
in Unified Communications Infrastructure
06-07-2011
06-07-2011
Hi,CUCM8.5 needs T-Server updated to 8.1. Genesys is releasing T-Server
8.1 at the end of July 2011....
Created by
lachlanpeters
in Other Collaboration Subjects
03-21-2011
03-21-2011
Hi, /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table
Normal"; mso-tstyle-rowband-...
Created by
lachlanpeters
in Policy and Access
06-30-2010
06-30-2010
It is on a switch ( 2960, 3560 and 3750. All IOS at most 1 year old)I am
looking basically if anyone...
06-20-2010
Hi All,I am needing to find away to monitor if a monitor sessions is
created/deleted or change.Is th...
04-19-2010
No Windows Firewall and I have removed Symentec Endpoint which has a
"firewall" in it.jrm is still n...
Public Statistics
| Date Registered | 04-07-2010 06:08 PM |
| Date Last Visited | 04-15-2019 09:26 PM |
| Total Messages Posted | 16 |
