About jkay18041

jkay18041 · 03-09-2022

I have a 4500x switch that had the IOS deleted accidently.When booted this is what we get. ***************************************************************** ** Rom Monitor NVRAM configuration is being initialized to ** default values. This may be bec...

jkay18041 · 01-11-2022

Hopefully I can explain this well enough. I have a hub that is an ASA and I want to create a VPN to an asa on Spoke A. The hub inside is 10.19.1.0 and the remote side is 10.1.1.0 On spoke A the true inside is 192.168.1.0 but I am wanting to NAT...

jkay18041 · 08-19-2021

I've got 6 switches in a stack and the CPU usage is quite high.CPU utilization for five seconds: 97%/2%; one minute: 94%; five minutes: 82%PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process257 302010 7779 38823 66.26% 54.67% 43.82% 0 HRPC dai r...

jkay18041 · 03-10-2021

I have an ASA 5508-x and I've got a vendor who wants to create a site to site vpn between us and their ASA. They would like to give me a /28 subnet of private IPs to use to avoid overlapping on their network and then they want me to nat those to my a...

jkay18041 · 10-16-2020

I'm for some reason having a hard time getting an ACL to work on my ASA 5515. I've created a Network Object group called Blocked_IPs and have added some public IP's I want to block inbound to the ASA. On my outside interface I've set a new rule at th...

jkay18041 · 03-10-2022

rommon 1 >dirusage: dir { [ bootflash: ] | [ slot0: ] | [ usb0: ] }rommon 2 >dir bootflash:ExtX super block invalid signatureThank you for your assistance

jkay18041 · 03-09-2022

Here is what I get rommon 1 >setPS1=rommon ! >RommonVer=15.0(1r)SG6SupportedFeatures=1ConfigReg=0x0102rommon 2 >dir flash:Invalid path flash:usage: dir { [ bootflash: ] | [ slot0: ] | [ usb0: ] }

jkay18041 · 03-09-2022

I did read that post and here is what I did and it just seemed to go back to the rommon after i ran the boot tftp command. config-register = 0x102Writing to Primary Region failedWriting to Backup Region failedAutobooting using BOOT variable specified...

jkay18041 · 01-13-2022

Here is the config of the spoke. The hub just has a site to site vpn with no special nat rules, I have the VPN set to exempt NAT on the vpn. interface GigabitEthernet0/0description WANspeed 100duplex fullnameif outsidesecurity-level 0ip address ...

jkay18041 · 01-12-2022

I created a site to site vpn and it's working. Everything seems to be working as I want, but I have no idea why or how the NAT is working unless by default the nat rule nat (inside,outside) source static obj-192.168.1.0 obj-10.1.1.0 destination stat...

Member Since	‎05-05-2014 02:31 PM
Date Last Visited	‎03-17-2022 04:57 PM
Posts	284
Total Helpful Votes Received	10

User Statistics

User Activity

issues booting 4500x switch

Natting on ASA for VPN tunnel

High CPU usage on 3750x Stack

IPSec VPN Nat question

Blocking traffic on ASA from group of public IPs

Re: issues booting 4500x switch

Re: issues booting 4500x switch

Re: issues booting 4500x switch

Re: Natting on ASA for VPN tunnel

Re: Natting on ASA for VPN tunnel