I have a Cisco Switch 3850X which is totally fibre interfaces. I have created 5 vlan and there is intervlan routing at L3 in the switch. Each vlan has dhcp pool. The switch is further connected to 8 access switches with gigaethernet access ports. At access layer, all the ports are getting dhcp of their respected vlan and can ping to other vlan and their default gateway.    Our internet router has ip address 192.168.8.1 which is normal modem, not Cisco router. To connect to internet, I have created separate vlan 80 and made L3 routing. interface vlan 80 has the ip address 192.168.8.254.   interface Vlan30 ip address 192.168.3.1 255.255.255.0 ! interface Vlan40 ip address 192.168.4.1 255.255.255.0 ! interface Vlan50 ip address 192.168.5.1 255.255.255.0 ! interface Vlan60 ip address 192.168.6.1 255.255.255.0 ! interface Vlan70 ip address 192.168.7.1 255.255.255.0 ! interface Vlan80 ip address 192.168.8.254 255.255.255.0   This vlan is assigned to the port in other switch which is having the access vlan 80. And ethernet is connected to the router 192.168.8.1.  I created below ip route ip route 0.0.0.0 0.0.0.0 192.168.8.1  to point internet traffic to the internet router.  From the main core switch 3850, I am able to ping the router and also innternet dns 8.8.8.8 which means internet is working there. But when my computer is connected to any other vlan IP Address like 192.168.3.0, I am able to ping 192.168.8.254 only. While I can't ping the connected router which is 192.168.8.1. Thus I am not able to ping the internet also or 8.8.8.8 from the PC.   Could anyone suggest the possible reason or solution? Will appreciate your help in this regard.  ... View more

Hi guys,    We have a customer which is using Cisco Phone 8961. User is configured to use End User page and update his custom settings from end user page. End User added some SD buttons to his phone but it is not appearing in the actual phone.  When from Admin page I checked, the phone successfully got the SD configuration configured by the End User from End User page. I need to restart the phone from the system to update it while it should restart automatically.    Now End User is configuring the SD successfully, but he is contacting me to restart the phone from Admin page. Is there anyway tor resolve the issue? Either there should be a way to automatically update the config on actual phone, or a way to restart the phone from the End User page.  ... View more

Hello, I hope u all guys are doing fine. I'm experiencing an issue with one of our clients. We are using Cisco CME Router and a basic auto attendant on it. Just a greeting message, then dial 0 for operator or extension. For this we have made FXO ports on Plar immediate to 250. This 250 is the pilot of a tcl script which generates and collects the digits to transfer the call to operator or desired extension... When the call is redirected to any extension, it will only show caller-id as 250 which isn't original caller-id. It means all the incoming calls on FXO ports are showing caller-id as 250. Is there any command in the tcl script or while creating the application for auto-attendant to keep the the original caller-id even after redirecting the call? Thank you so much in advance. voice-port 0/0/0 trunk-group FXO no vad cptone BE connection plar opx immediate 250 caller-id enable caller-id alerting line-reversal caller-id alerting dsp-pre-allocate application service aa flash://its-CISCO.2.0.1.0.tcl param operator 0 paramspace english language en paramspace english index 0 paramspace english location flash:// param aa_pilot 250 paramspace english prefix en param aa-pilot 250 ! dial-peer voice 250 voip description AA dial-peer service aa destination-pattern 250 session target ipv4:192.168.8.1 incoming called-number 250 dtmf-relay h245-alphanumeric rtp-nte codec g711ulaw no vad ! ... View more