Hi all,   First of all, apologies if I picked the wrong section.   What I am wondering if the following is possible, if so do we have any guides?   I need to configure voicemail (Unity) on an analogue telephone that's being looped through a Cisco ATA 190.The user would dial into their voicemail so I've not got any issues with that but just how to actually setup the VM on the ATA. Would it be as simple as fording the call on busy no anser, no coverage, no answer etc and point it to my voicemail DN?   I've searched the internet and it seems possible but I am confused with how to carry this out and can't seem to find any documentation on how to do this.   Thanks for your time.   Thomas. ... View more

Hi all, We are trying to create a user experience that is easy for our customers which basically they connect to our wifi and once connected they simply only have to hit 'logon', 'connect' or something of that nature. Is this possible with ISE? We are using 5508's and Cisco ISE 2.1. I believe it is possible as the NHS in Britain do it. Not sure how they do it but would like some steer if anyone has done it or knows how to do it? Cheers, Thomas. ... View more

Hey, I'm just wondering if someone could help - I was trying to create a repositary for my ISE backup which is on an SFTP server but ISE sent a pop up to my screen stating: 'Host key of sftp server must be added through CLI using 'crypto host_key add' exec command before this repository can be used. Also ensure that the host key string matches the host name used in the URL of the repository configuration.' I've never setup an SFTP share for ISE - can anyone advise what this means and what the impact of running this command? Or does anyone know of any documentation to look over? We are using 1.3 patch 4 Cheers, Tam. ... View more

Hi,   I was just wondering if you could help - I am going to be deploying 802.1x to roughly 2000 endpoints that have Cisco handsets attached to them.   I have the configuration that I would want to put on the network device to query ISE and the 802.1x port configuration for the endpoint.   Does anyone know if you can set up a policy on Cisco PI to search for specific ports on a device that has a Cisco IP phone and once detected push the 802.1x port configuration to that specific port?   If it doesn't does anyone have any other tips and tricks to shorten the pain of going into each device.   Thanks, Thomas. ... View more

Guys,   I've built a lab in gns3, one router and one ASA, the ASA has an inside, DMZ (with a small network behind it with just 1 server up and running at present) and an outside interface whilst the router has 3 interfaces on 3 subnets that connect a PC in each of the subnets using VMWare.   I have attached a screenshot of my topology so that you better understand what I have done and included the config files. https://www.dropbox.com/s/zjag2pt2dgper9p/topology.png   Basically, what I am trying to achieve is be able to connect through a pc in say the HR subnet through to the webserver in the DMZ, the webserver is LAMP, which is a pre-built VMWare appliance that runs webservices and it's mainly to just test.   I'm obviously missing out somethign simple as I can see it trying to connect through the ASDM log messages. I have changed the firewall rules to reflect this but still no avail.   I would appreciate some assistance if someone could spare 5 mins, I would really appreciate it.   Thanks   Thomas. ... View more

Guys, I was just wondering if you can help me - we successfully moved our DC from our corporate HQ to our colo DC that is managed. This all went to plan apart from one thing - our netbackup server isn't joining the network - this was previously fine and the only change that is different is that the netbackup server was on an old 3750 switch that didn't have any gig uplinks but the new 3750 does (hopefully that makes sense). So this is the topology that has been created by the infrastructure team (and verified by myself a former UNIX sysadmin): a bonded interface with 4 nic's inside vlan 21 - I confirmed this with ifconfig -a but can't confirm it now as I don't have access to the server. I checked the IP, gateway and mask and they are all correct and it's participating in pagp. Now the switch side - we can see the MAC addresses with no issues but can't seem to ping the device on 172.16.21.51 - we understand that historically this was a bitch to setup but we don't remember the actual setup even though we've checked the old config and there isn't anything different. SLC-3750-Rack7#sh mac address-table vlan 21           Mac Address Table ------------------------------------------- Vlan    Mac Address       Type        Ports ----    -----------       --------    ----- All    ffff.ffff.ffff    STATIC      CPU   21    0015.17f8.a81a    DYNAMIC     Po7   21    0015.17f8.a81b    DYNAMIC     Po7   21    286e.d497.2cf3    DYNAMIC     Po7 Total Mac Addresses for this criterion: 24 As above the 3 interfaces are in po7 - we have taken the interfaces out of the port channel and set them up as access and trying just 1 port - still the same, we've also tried setting the port up as a trunk and this also is the same. I can also confirm that the group of interfaces need to be kept on the same 3750 switch and not across the stack. SLC-3750-Rack7#sh vlan bri VLAN Name                             Status    Ports ---- -------------------------------- --------- ------------------------------- 1    default                          active    Gi1/0/12, Gi1/0/19, Gi1/0/27, Gi1/0/28, Gi2/0/12, Gi2/0/27, Gi2/0/28 21   Backup                           active    Gi1/0/15, Gi1/0/16, Gi1/0/23, Gi2/0/15, Gi2/0/16, Po6, Po7 And as you see above the vlan is present on the switch SLC-3750-Rack7#sh run int po7 Building configuration... Current configuration : 176 bytes ! interface Port-channel7 description ..nbu5000 switchport access vlan 21 switchport trunk encapsulation dot1q switchport trunk native vlan 21 switchport mode access SLC-3750-Rack7#sh etherchannel 7 summ Number of channel-groups in use: 8 Number of aggregators:           8 Group  Port-channel  Protocol    Ports ------+-------------+-----------+----------------------------------------------- 7      Po7(SU)          -        Gi1/0/21(P) Gi1/0/22(P) Gi1/0/23(D)                                  Gi1/0/24(P) SLC-3750-Rack7#sh run int g1/0/21 Building configuration... Current configuration : 186 bytes ! interface GigabitEthernet1/0/21 switchport access vlan 21 switchport trunk encapsulation dot1q switchport trunk native vlan 21 switchport mode access channel-group 7 mode on If anyone can help with this it would be greatly appreciated. Thanks, Thomas. ... View more

Hi, I was just wondering if you could help - we have around 20 reports running on CW and we would like to delete/remove these scheduled reports - I've been looking through CW and I can't find the area where it will allow me to remove the actual reports - can anyone advise where this setting would be please? Thanks, Thomas. ... View more

Chaps, I have two data centres in HA mode - one active and one standby - if the active was to go offline due to a failure we would like the standby DC to take over as the active DC for the period of failure. Now to do this we need to keep everything in sync - this includes the firewall rules - is there a way to replicate the firewall rules from DC 1 to DC 2 automagically? At the moment we plan to do this manually and would prefer it obviosuly if this could be done in such a way that we wouldn't have to do repetitive work. Any help in this situation would be appreciated - i've done a wee diagram that reflects our setup in a simple mans head. Thanks, Thomas. ... View more