Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About vraut
08-18-2017
Stats
Member since
10-03-2002
33
Posts
10
Helpful
0
Solutions
Created by
vraut
in Collaboration, Voice and Video Documents
in Collaboration, Voice and Video Documents
08-29-2013
10:58 AM
08-29-2013
10:58 AM
Hello, The Jump upgrade or Upgrades to 9.1(2) is for CUCM versions as specified in the respective documents at https://communities.cisco.com/community/partner/collaboration/migration However for BE5K the migration path is BE 5k -> upgrade to 9.x -> then migrate to BE6K (please make sure the BE6K hardware compatibility) or BE 5k -> upgrade to 9.x -> then migrate to CUCM (Please make sure you are covered for licensing) Another posibility to cover, since this is also possible; is to export endpoints and data, sanitize it for your target version and Import the endpoints and data and recreate the dial plan. You will have to consult the licensing team so you are covered on that front. Thanks Viraj
... View more
Created by
vraut
in Collaboration, Voice and Video Documents
in Collaboration, Voice and Video Documents
07-08-2013
11:11 AM
07-08-2013
11:11 AM
Direct Upgrade Procedure for Cisco Unified Communications Manager Releases 6.1(2)—9.0(1) to 9.1(x) Introduction This document provides procedures for performing a direct upgrade to Cisco Unified Communications Manager (Unified Communications Manager) Release 9.1(x) from Releases 6.1(2) through 9.0(1). About direct upgrades You cannot upgrade directly to Unified Communications Manager Release 9.1(x) from Releases 6.1(2), 6.1(3), 7.0(1), 7.0(2), and 7.1(2). For these releases, you must perform the upgrade in three stages: 1 Upgrade to Release 6.1(4) or 7.1(3) as an intermediate release. 2 Perform a direct upgrade to Release 9.1(x). 3 Virtualize Release 9.1(x). The procedures in this document support high availability for all three stages of the upgrade. This document is applicable to Unified Communications Manager clusters with the following environment: • Any of the following Unified Communications Manager Releases are installed: 6.1(2) through 9.0(1). • All of your current Media Convergence Server (MCS) servers support Unified Communications Manager Release 9.1(x). • No changes are required to the IP addresses or hostnames for the Unified Communications Manager upgrade. If you need to change IP addresses or hostnames, you must do so in a separate maintenance window, prior to the upgrade. For more information, see Changing the IP Address and Hostname for Cisco Unified Communications Manager, Release 9.1(1).
... View more
- Tags:
- callmanager
- cucm
- cucm9.x
- cucm_migration
- cucm_upgrade
- direct_upgrade
- drive29
- drive_to_9
- licensing
- migrate
- migration
- upgrade
- upgrade_software
- upgrading
Labels:
Created by
vraut
in Collaboration, Voice and Video Documents
in Collaboration, Voice and Video Documents
07-08-2013
10:59 AM
07-08-2013
10:59 AM
Direct Upgrade Procedure for Virtualized Cisco Unified Communications Manager Release 8.0(2)–9.0(1) to 9.1(x) Introduction This document provides procedures for performing a direct upgrade to Cisco Unified Communications Manager (Unified Communications Manager) Release 9.1(x) from virtualized Releases 8.0(2) through 9.0(1). About direct upgrades Unified Communications Manager Releases 8.0(2) and higher support virtualization. This document is applicable to Unified Communications Manager clusters with the following environment: • Any of the following Unified Communications Manager Releases are installed: 8.0(2) through 9.0(1). • Your current Unified Communications Manager release is running in a virtualized environment. • No changes are required to the IP addresses or hostnames for the Unified Communications Manager upgrade. If you need to change IP addresses or hostnames, you must do so in a separate maintenance window, prior to the upgrade. For more information, see Changing the IP Address and Hostname for Cisco Unified Communications Manager, Release 9.1(1).
... View more
- Tags:
- callmanager
- cucm
- cucm9.x
- cucm_migration
- cucm_upgrade
- direct_upgrade
- drive29
- drive_to_9
- licensing
- migrate
- migration
- upgrade
- upgrade_software
Labels:
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
11-27-2004
10:28 PM
11-27-2004
10:28 PM
Hi, Only FXS/FXO ports show up on the gatekeeper as E.164-ID. This is the E.164 format number the gatekeeper uses to route calls by. In the event the ports on the gateway are ISDN then the "zone prefix.." CLI helps. Wild card numbers will not show on the gatekeeper as E164-ID. In later versions of IOS the support for Dynamic Prefix registrations (H.323 v4) help register the ISDN E.164 numbers of the ports. On the gateway you will need to have "ras rrq dynamic prefixes" under voice service voip -> h323. Also on the gatekeeper you will need "rrq dynamic-prefixes-accept" under gatekeeper config. "sh gatekeeper zone prefix all" displays the dynamic prefixes too. Thanks
... View more
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
08-02-2004
02:51 PM
08-02-2004
02:51 PM
Hi Charles, You may want to refer AAR docs at the links below http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00801ec5a4.html http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00801f007f.html If the GK is across the WAN from the CCM, AAR will help route calls to the Local PSTN gateway. If The remote branches need to route calls to the PSTN, SRST will be helpful here the MGCP devices will have to fallback to H323 for routing those local calls to local PSTN. http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_configuration_guide_chapter09186a00801f3ac7.html http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/vvfax_c/callc_c/ccm_c/intcnf1.htm#wp105683 Regards
... View more
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
11-13-2002
09:57 AM
11-13-2002
09:57 AM
Hi, Since you are using the IP phone, check the default router on the Ip phone, check where the Packets from the Ip phone are going "debug ip packet". Sniffer trace will tell you more details. If you are using NAT on the router check the "voice-class source interface " under dial-peer voip. Thanks Viraj
... View more
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
10-24-2002
09:56 PM
10-24-2002
09:56 PM
Hi, Have you tried the "voice-class codec" CLI you can give a list of codecs with preferences, with this one may not require transcoding as the gateway now is capable of speaking multiple codecs. Regards Viraj
... View more
10-24-2002
09:51 PM
Hi, 12.2(11).T as it is latest, 12.2(2).XB3 mostly used for the AS53xx but before have a look at the feature navigator to check the features that you require. http://www.cisco.com/cgi-bin/Support/FeatureNav/FN.pl Regards Viraj
... View more
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
10-24-2002
09:47 PM
10-24-2002
09:47 PM
Hi, Sounds like a Codec mismatch for the second line, check it out. Try making the call only with the second line when the first line is on-hook. Regards Viraj
... View more
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
10-24-2002
09:42 PM
10-24-2002
09:42 PM
Hi, Hi, Using Class of restriction one can restrict dialing plans http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca716.html#xtocid19 Hope this helps. Regards Viraj
... View more
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
10-24-2002
09:41 PM
10-24-2002
09:41 PM
Hi, Using Class of restriction one can restrict dialing plans http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca716.html#xtocid19 Hope this helps. Regards Viraj
... View more
Created by
vraut
in Other Collaboration Subjects
in Other Collaboration Subjects
10-24-2002
09:33 PM
10-24-2002
09:33 PM
Hi, Try the recovery option in the service properties, Add the restart service for first and second failure with 2/3 mins between failures. What may be happening is that since your CallManager is a demo server, resources such as memory and CPU type and speed may not be as per recommended. So when you install new services around the CallManager, next when the SQL server comes ,additional processes update the SQL server, in which time if the CallManager tries to start but finding the SQL server response slower fails to start. It may have occured to you that its rather funny that the CallManager service doesnt complain on later reboots. Regards Viraj
... View more
10-03-2002
03:57 PM
Hi, Configure on the 26xx a voip dial-peer with prefrence pointing to the VG200 and the VG200 configured with pots for PSTN connectivity and voip for servicing incomming calls from the PSTN. Under normal case the higher order voip dial-peer on the 26xx works, under SRST the second prefrence voip to the VG200 is used by the 26xx Regards
... View more
Created by
vraut
in Collaboration, Voice and Video Documents
08-29-2013
08-29-2013
Hello,The Jump upgrade or Upgrades to 9.1(2) is for CUCM versions as
specified in the respective doc...
07-08-2013
Direct Upgrade Procedure for Cisco Unified Communications Manager
Releases 6.1(2)—9.0(1) to 9.1(x)In...
07-08-2013
Direct Upgrade Procedure for Virtualized Cisco Unified Communications
Manager Release 8.0(2)–9.0(1) ...
Created by
vraut
in TelePresence and Video Infrastructure
08-17-2010
08-17-2010
Hi,Try this
link.http://www.cisco.com/en/US/solutions/ns340/ns414/ns742/ns818/landing_video_conf.htm...
11-24-2009
You may want to use the DSP
calculatorhttp://www.cisco.com/cgi-bin/Support/DSP/dsp-calc.pl
12-27-2004
Hi,yes, the IPIP gateway can provide H.323 proxy functionality.Since the
IPIP gateway also is aware ...
11-27-2004
Hi,Only FXS/FXO ports show up on the gatekeeper as E.164-ID. This is the
E.164 format number the gat...
Created by
vraut
in TelePresence and Video Infrastructure
11-08-2004
11-08-2004
Hi,If you use the Cisco router as FW this link may be of
help.http://cisco.com/en/US/partner/product...
11-08-2004
Hi,Yes, very much.Since you are using VoIP in which case the signalling
components may use TCP or UD...
Created by
vraut
in TelePresence and Video Infrastructure
11-08-2004
11-08-2004
Hi,Try this additional link
toohttp://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cg...
Created by
vraut
in TelePresence and Video Infrastructure
11-08-2004
11-08-2004
Hi,http://cisco.com/en/US/products/sw/voicesw/ps5640/index.htmlTry this
product, you may need the la...
11-08-2004
Hi,http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&mibName=CISCO-GATEKEEPER-MIBThis
lin...
11-08-2004
With your approach you may have the MCM as H.323 Proxy and NAT (on the
Firewall) both the MCM Proxy ...
08-02-2004
Hi Charles,You may want to refer AAR docs at the links
belowhttp://www.cisco.com/en/US/products/sw/v...
Public Statistics
| Date Registered | 10-03-2002 03:48 PM |
| Date Last Visited | 08-18-2017 04:03 AM |
| Total Messages Posted | 33 |
| Total Helpful Votes Received | 10 |
