Hi, Just want to share my experience when getting to CCNP Collab. Your case is the same as mine before. I'm a CCNA Voice holder and also passed  CVOICE (642-437) and CIPT1 (642-447) and stepping up to CCNP Voice but since voice certification was retired I shifted to CCNP Collab and I needed to pass the CCNP Collab exams. CIPTV2 (300-075) CTCOLLAB (300-080) CAPPS (300-085) After passing it, I didn't get CCNP Collab certification until I pass CCNA Collaboration first. During my case since I'm a CCNA Voice holder and passed  ICOMM (640-461), i just need to pass CIVND (210-065) to become a CCNA Collab. Passing my CCNA Collab automatically certifies me as CCNP Collab as well. Since you are CCNA Voice holder you need to migrate first to CCNA Collab and need to pass  CIVND (210-065) before getting to CCNP Collab. But if you are ready for your CIPTV2 exam you can proceed but passing it will not certify you as CCNP Collab until you pass CCNA Collab. regards, Acevirgil ... View more

Premium Resolution License This will enable your endpoint to transmit video resolution up to 1080p60. regards, Acevirgil ... View more

I think that's your problem where it's not a supported deployment.  The right deployment should be: VCS Control - VCS Expressway Expressway Core - Expressway Edge If you will deploy MRA with B2B the Expressway series (Core + Edge) is the right to position. To make your VCS Expressway to become Expressway-E you need licenses for that. LIC-EXP-SERIES LIC-EXP-GW LIC-EXP-TURN LIC-EXP-AN LIC-EXP-E LIC-EXP-RMS I would suggest to contact your Cisco AM for licensing concerns. regards, Acevirgil ... View more

To add on Manish provided links, for you to able to make it work as standalone H323 endpoint make sure to enable the H323 network service. This is disabled by factory default. You need to check on that. Under Configuration > System Configuration > NetworkServices > H323 Mode: On regards, Acevirgil ... View more

Also take note of the EOS/EOL notice for CTI-CE500-BDL-K9. http://www.cisco.com/c/en/us/products/collateral/unified-communications/telepresence-video-communication-server-vcs/eos-eol-notice-c51-735718.html regards, Acevirgil ***Please rate or mark as correct answer if this post is helpful. ... View more

I believe this is an appliance VCS using Cisco UCS C220 M3 server. The VCS is already installed on the server. You should have 2 separate servers for this. 1 for VCS Control and 1 for VCS Expressway. Data sheet is found here: http://www.cisco.com/c/en/us/products/collateral/unified-communications/telepresence-video-communication-server-vcs/data_sheet_c78-626491.html regards, Acevirgil ***Please rate or mark as correct answer if this post is helpful. ... View more

Microphone is ordered separately with some options to choose See sample CCW configuration, in the figure i used CTS-MIC-TABL60 microphone.  The unit doesn't comes with a speaker so you may order it separately. If the SX80 will be set up on a small meeting room with LCD/LED TV displays with built-in speakers, you can utilized the built-in speakers on the displays for your SX80. regards, Acevirgil ... View more

The camera shelf is ok and also the position. Make sure theres a hole in the camera shelf for you to put a screw on the buttom of the camera to fixed and secure the camera. regards, Acevirgil ... View more

The supported VMware host and tested to deploy VCS ova is ESXi in Cisco UCS server platforms. See page 4 on this guide for the minimum requirements: http://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/vcs/config_guide/Cisco_VCS_Virtual_Machine_Deployment_Guide_X7-2.pdf Not sure if will work with workstation 7 running on the server that you are using. regards, Acevirgil ... View more

Hi, Have you managed to integrate the Biamp Audia VoIP 2 card with your CUCM? I have also customer and wants to integrate the system in the CUCM. What licenses do you used in CUCM? Hows the integration? do you have any issues encountered? regards, Acevirgil ... View more

I think this post regarding receiveing unknown calls is similar to https://supportforums.cisco.com/discussion/12690631/telepresence-mx300-g2 in TelePresence section. What do you mean in your statement " WE need the video number and activation code"? If you are refering to activation code or the Release Key, you may request it using the Cisco Licensing Tool https://tools.cisco.com/SWIFT/LicensingUI/Quickstart# on the Get Other Licenses > TelePresence Software Release Key. Or if you find hard to get those keys you may contact directly Cisco Licensing team via email request to licensing@cisco.com. Also what do you mean you need a video number? regards, Acevirgil ... View more

FXO ports, like all the other analog interfaces, carry one call per port, so each RJ-11 port on your Cisco ISR router connects to one line from the PSTN and carries a single call at a time. A second call is given a busy tone if it tries to use the same port or line. It does not depend on the DSP nor bandwidth.   regards, Acevirgil ... View more

You can mount the Precision 60 camera inside the wall. I already installed some on our customer and they prefer it to be flushed inside the wall for better aesthetic look of the room. Just make sure the camera can move freely (pan and tilt) to its maximum positions when mounted and can capture the whole area with its viewing angle when the lens is positioned on the center of the conference table.   regards, Acevirgil ... View more