About sebastien.charles

sebastien.charles · 01-16-2024

Hello, I would like use Webex API for monitor the statut of the SIP trunk like you can see it in Control Hub. Could you tell me if is it possible ? I just found that API for list all trunks : https://webexapis.com/v1/telephony/config/premisePstn/t...

sebastien.charles · 07-18-2017

Hello, We have recently buy and install a new MX800 for my customer but during the installation , a part is missing. Please found in attach a photo and a schema for understand exactly the missing part. Could you tell me what is the process for...

sebastien.charles · 01-19-2015

Hello, I receive this alarm continuously =>LogPartitionLowWaterMarkExceeded That is normal because the Used Disk Space is 91%. I have found on my CUC that the file below takes more than 136 Mo. admin:file list activelog cuc * detail size 19 Jan,2015 ...

sebastien.charles · 02-20-2009

Hi,I have CCM in release 4.2On E1 qsig link between a CISCO 2851 and IP PBX ALCATEL, some ITs goes out-of service.I only seen this status in RTMT (see in screen shoot in attach)Do you kwon why this channel goes in out-of service status??When I make a...

sebastien.charles · 12-13-2007

Hi,We have problem with CCM in 4.0(2a)sr1a and H323 GW ( 1760 in 12.3(8)T3 )We have the same route pattern for all international call.All international call works excepted call to Slovakia.In isdn trace, we see this disconnect cause 0x8798.Do you hav...

sebastien.charles · 02-20-2009

Hi We have expeted some problem yesterday at the same time.In the new Â« sh controller E1 Â», there is no new error.ISRROTONDE1#sh controller E1 E1 0/0/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not se...

sebastien.charles · 02-20-2009

Please found below the sh controller E1I have the problem on this to linksE1 0/0/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20060623, FPGA: 20, spm_count = 0 Framing is...

sebastien.charles · 02-20-2009

I'm in c2800nm-ipvoicek9-mz.124-9.T3.bin

sebastien.charles · 09-10-2007

Hi thanks for this update.We have two sites (A and B) manage with the same callmanger. The callmanger was located on site A.When we make this call, we have the problem => phone (site A) -- GW--- PSTN --- GW ---phone (site B).When we try to joint the ...

sebastien.charles · 06-06-2005

Thanks for this answerBut my customer have made no modification in configuration.Do you have more information about "SynConfig" in 2005 Jun 05 14:58:30 %SYS-6-CFG_CHG:Global block changed by SynConfig// ????For information, my customer have 2 superv...

Member Since	‎10-21-2003 06:14 AM
Date Last Visited	‎03-01-2024 12:02 AM
Posts	24

User Statistics

User Activity

Webex API for monitor the statut of the SIP trunk

MX800 / missing part

LogPartitionLowWaterMarkExceeded on unity connection 8.6.2.21012-1

MGCP Gateway / On E1 qsig => Somes channels out-of-Service

International call fail to Slovakia

Re: MGCP Gateway / On E1 qsig => Somes channels out-of-Service

Re: MGCP Gateway / On E1 qsig => Somes channels out-of-Service

Re: MGCP Gateway / On E1 qsig => Somes channels out-of-Service

Re: problem for receive some call

Re: Error messages unexplained in module 8 (ws-x6348-RJ45) with