hope these URLs will answer your query. http://www.cisco.com/en/US/products/ps5854/products_installation_guide_chapter09186a00802c5af1.html#wp1037377 http://www.cisco.com/en/US/products/hw/routers/ps282/products_installation_guide_chapter09186a008007dfd5.html#wp1035587 http://www.cisco.com/en/US/products/ps5855/products_installation_guide_chapter09186a00802ccf1d.html#wp1008593 rate if it does .... ... View more

problem indicates that DNS server and domain configured is not able to resolve IP address of the device you are trying to access. you can define a static host name-to-address mapping in the host cache, use the ip host global configuration command. configure below command and then check if you are able to ping using hostname or not. ip host switch1 HTH, rate if it does ... ... View more

try with "confreg" command and see if it works for you. ... View more

Hope this URL will give information you are looking for. www.cisco.com/warp/public/473/101.pdf rate if it does .... ... View more

use "service password-encryption" command in config mode to encrypt passwords. To change telnet and vty password, configure new password under interface config mode and you should be good to go. line vty 0 4 password linet console0 password HTH, rate if it does .... ... View more

can you share "show version" output of the cisco 2500 router? I feel router should boot with the 11.2 code without any issue. existing IOS code running will support only a set of features. you will ran into problem only if you try to configure some feature which is not being supported by that particular IOS. also if there are any bugs associated with the current IOS and features running, those bugs can sometimes cause problem. HTH, rate if it does .... let us know if you have more questions... ... View more

hope this URL will answer your query. http://www.cisco.com/en/US/products/hw/switches/ps628/products_configuration_guide_chapter09186a008007e8c7.html#xtocid22 rate if it does... ... View more

can you tell us how you have configured 2950 to VTP client? can you try to configure VTP in config mode instead of vlan database mode and see if it works for you. switch(config)# vtp mode server OR switch(config)# vtp mode transparent HTH, rate if it does .... ... View more

there is no way you can configure switchport to remain up even when the device connected to it is switched off. if laptops and server which has wake on LAN (WOL) utility installed is on same VLAN, then you should be able to boot laptops even when they are switched off. WOL utility will take care of it to power on the laptop through MAC address, request from WOL server will be broadcasted to all ports which are in the same VLAN and appropriate device will respond to the server and get powered on. problem occurs when laptop and wake on LAN server are in different VLANs because layer 3 devive which do inter-vlan routing will stop directed broadcast which is not your case as you have laptops and WOL server in the same VLAN. HTH, rate if it does .... ... View more

are you able to ping the remote end interface IP 10.200.200.2 from router? ... View more

hope this URL will be of some help. http://www.cisco.com/en/US/products/hw/switches/ps5023/products_data_sheet0900aecd80371991.html rate if it helps ... ... View more

looks to me is the loose fitting of power cable to the router. Once cable was reseated, router turned on. ... View more

In Class C network, you have 8 bits in host portion and 24 bits in network portion. Subnetting is to create subnets of an exisitng network by borrowing bits from host portion. So you can create subnets by borrowing 1-6 bits from host portion because you have to leave atleast 2 bits in host portion to have atleast 2^2-2=2 hosts. so IP address 200.200.50.0/25 will have 255.255.255.128 subnet mask. check this URL to get more information. http://www.cisco.com/warp/public/701/3.html hope this answer your query .. rate if it does ... ... View more