Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Garvan Long
‎06-08-2018
Beginner
Recent Badges
Awards
Recent Badges
See all
1 Helpful Vote
10 Replies
5 Replies
50 Replies
1 Accepted Solution
10 Helpful Vote
5 Accepted Solution
20 Replies
Stats
Member since ‎10-02-2011
54
Posts
25
Helpful
6
Solutions

TMS Alerts for Active Conferences

Created by in TelePresence and Video Infrastructure
07-23-2012
07-23-2012
Email Events are on a per device basis as opposed to per confernece. These can be configred under Ev...

Mcu 4505 call preconfigured participants

Created by in TelePresence and Video Infrastructure
07-23-2012
07-23-2012
If you enable" Use conference name as caller ID" check box on the confernece settings page it will u...

Re: Using TMS for scheduled calls in a SIP only environment Cont

Created by in TelePresence and Video Infrastructure
07-11-2012
07-11-2012
Is it a point to point to point call (TCS & 1 other endpoint ) or multipoint call. If multipoint who...

Re: Booking Polycom HDX via TMS

Created by in TelePresence and Video Infrastructure
07-11-2012
07-11-2012
TMS and TMSXE is going to give you the same result. I've seen a probelm in the past where TMS partia...

Using TMS for scheduled calls in a SIP only environment Content

Created by in TelePresence and Video Infrastructure
07-11-2012
07-11-2012
How are you scheduling in TMS, are you seleciting a recording alias in the recording drop down box o...

TMS vs MCU redial behavior

Created by in TelePresence and Video Infrastructure
07-02-2012
07-02-2012
I see quite a few people schedule dial out to Movi but personally i find it a bit strange to schedul...

TMS vs MCU redial behavior

Created by in TelePresence and Video Infrastructure
07-02-2012
07-02-2012
When you are testing this make sure you are in front of an enpoint thats part of the schedueld call ...

Re: Issues with SIP when registered to VCSE

Created by in TelePresence and Video Infrastructure
06-06-2012
06-06-2012
Hi TomoIf you only enable H323 on the trversal link, will this break external Movi users singing in ...

Re: Placing the VCS-E Starter Pack outside of a firewall

Created by in TelePresence and Video Infrastructure
06-06-2012
06-06-2012
I have seem implementations like this in the past but as Tomo indicated that it recommended to put t...

Re: VCSE not passing calls to a registered Polycom HDX9000

Created by in TelePresence and Video Infrastructure
06-06-2012
06-06-2012
Hi George if you are on version X7 tracing is enabled from the Maintenance menu. If you are on earle...

Move endpoints from one TMS to an other

Created by in TelePresence and Video Infrastructure
06-06-2012
06-06-2012
Hi MartinCan you use the AdminTool>Configuration>Netwroks>Advanced Network Settings for Systems on P...

Re: VCSE not passing calls to a registered Polycom HDX9000

Created by in TelePresence and Video Infrastructure
06-06-2012
06-06-2012
Hi Have you taken a diagnostic trace or a netlog of the SIP registration of the Polycom. It may not ...

MX200 QoS settings not marking packets

Created by in TelePresence and Video Infrastructure
05-16-2012
05-16-2012
Where are you taking the sniffer trace from ? could it be remarked in the path to your sniffer

VCS Neighboring

Created by in TelePresence and Video Infrastructure
05-16-2012
05-16-2012
If you register two endpoint to the vcs control and they can call each other repeat the test on the ...

No incoming video and audio for new Jabber video account

Created by in Jabber Video Support
05-15-2012
05-15-2012
See https://supportforums.cisco.com/message/3636239#3636239
Public Statistics
Date Registered ‎10-02-2011 03:33 PM
Date Last Visited ‎06-08-2018 02:45 AM
Total Messages Posted 54
Total Helpful Votes Received 25