Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About ssnickson
Stats
Member since
09-02-2010
13
Posts
0
Helpful
0
Solutions
12-21-2010
08:17 PM
So if i get GLC-FE-100FX SFP module and plug it in 2960-24TC-L and Then can i work to link between unmanaged switch and Cisco Switch. The unmanaged switch is 100FX
... View more
12-21-2010
05:12 PM
Actaully I m using 2960-24TC-L I have attched the copy of table which i got from Cisco Website. it stated there that GLC-FE-100FX Description: Operates on ordinary multimode fiber-optic(MMF) link spans up to 2 kilometerslong. For 100Mbps Ethernet ports and also i got to the that 2960 is supporting GLC-FE-100FX so does that mean if i buy GLC-FE-100FX SFP module it should be able to work? If i stated anything wrong please advice me Information i got from Datasheet Cisco Catalyst 2960-S and 2960 with SFP-based ports: ● 10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 UTP cabling ● 100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling ● 1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling ● 1000BASE-T SFP-based ports ** : RJ-45 connectors, 4-pair Category 5 UTP cabling ● 1000BASE-SX -LX/LH, -ZX, -BX, -T, * -FX, * and CWDM SFP-based ports: LC fiber connectors (single/multimode fiber) ● 100BASE-LX, -BX, -FX SFP-based ports: LC fiber connectors (single/multimode fiber) * GLC-T and GLC-GE-100FX are not supported on the Cisco Catalyst 2960-8TC-S, 2960-8TC-L, or 2960G-8TC-L switches.
... View more
12-20-2010
05:10 PM
I have cisco switch 2960 and a unmanaged switch etherwan. please find the attached datasheet for your reference on the unmanaged switch. Now i using SPF module (Fibre) to connect the Gig port to the Fibre port of the unmanaged switch. The port of the unmanaged switch is not an Gig port it is 100Fx. I have checked the connection by using RJ45 link in cisco switch and the unmanged switch. I managed to ping When i connect the switch using the Gig port using fiber module i cannot ping I do know that we can buy a Gig port unmanaged switch. But in this case we have already bought the hardware Need your advice on how to solve this issue. I need the solution for this as soon as possible
... View more
Labels:
09-22-2010
03:04 AM
When i try to install Net manag er 1.1 in windows server 2003. I get an error says "Error launching ExcuteSQL" . What could be the possible cause of this error. I would like to get experts guidance on this issue. Thanks in advance
... View more
Labels:
Created by
ssnickson
in IP Telephony and Phones
in IP Telephony and Phones
09-15-2010
08:59 PM
09-15-2010
08:59 PM
Thanks for your solution. I have one question on that attachement If you look into that attachedment there is one device they indicate as cisco call manager express Does that Cisco call manager is a hardware device? or the cisco call manager is the software which is pre-intalled in the router? step 4,5,6,7,8,9 is pointed out from cisco call manager. But the configuration will be done at router or any other special hardware required?
... View more
Created by
ssnickson
in IP Telephony and Phones
in IP Telephony and Phones
09-14-2010
10:44 PM
09-14-2010
10:44 PM
Thanks I have never worked on Call manager before i m newbie to this But i heard from my supplier that the router is pre install with CCM When i checked the CCM using show command. It says that CCM is not enabled. So that why i confused how to enable it
... View more
Created by
ssnickson
in IP Telephony and Phones
in IP Telephony and Phones
09-14-2010
07:56 PM
09-14-2010
07:56 PM
I have a cisco Router 3900 Series Need to know how to enable the Call manager express in the Router? I have smartbill software to communicate with the Call manager.
... View more
Labels:
09-03-2010
01:49 AM
i would like to know how to config to connect a 3900 series router with the 4500 series switch. and i need to test the communication. I need it urgently.thanks
... View more
Labels:
09-03-2010
12:06 AM
Hi Marshall, Meaning to say that ip phone IP address has to be within the VLAN IP range ? ok my IP Phone Address are 10.10.12.3 and 10.10.12.2 (Default when we connect) I set the VLAN as 10.10.12.0 So do i need to do anything on the IP Phone ? or need to do setting in the switch?
... View more
09-02-2010
11:59 PM
For "If the module is in slot 1, then try interface gig/fast 1/? If the port is L2, then you cannot assign an IP address. Like Jon mentioned, assign the port to a VLAN" The module is actually in slot 1 i tried using gi0/1 and fast0/1 but it still gives me the same error when i try help with ? under gi ? it only show <1-7>
... View more
09-02-2010
11:28 PM
Hi marshall, THanks for your reply. I have tried the command you have advice i can set the vlan but when i try to set the ip address for a particular port. I doest allow me to enter 0/1. it always says % Invalid input detected at marker and the marker is at 0. What could be the possible error
... View more
09-02-2010
02:57 AM
I m very new to networking line. I have Cisco 4507R-E as core switch and i have connected to the console to do my intial setup. I have 1 24 port module at 1st slot. I would like to know how to config a IP address to the port? . I have 2 Cisco IP Phone connected to the switch. Need to set the IP for these two IP Phone and need to ping and try the connection. I need it very urgently.Thanks in advance
... View more
Labels:
12-21-2010
So if i get GLC-FE-100FX SFP module and plug it in 2960-24TC-L and Then
can i work to link between u...
12-21-2010
Actaully I m using 2960-24TC-L I have attched the copy of table which i
got from Cisco Website. it s...
12-20-2010
I have cisco switch 2960 and a unmanaged switch etherwan. please find
the attached datasheet for you...
09-22-2010
When i try to install Net manager 1.1 in windows server 2003. I get an
error says "Error launching E...
09-15-2010
Thanks for your solution. I have one question on that attachementIf you
look into that attachedment ...
09-14-2010
Thanks I have never worked on Call manager before i m newbie to thisBut
i heard from my supplier tha...
09-14-2010
I have a cisco Router3900 SeriesNeed to know how to enable the Call
manager express in the Router?I ...
09-03-2010
i would like to know how to config to connect a 3900 series router with
the 4500 series switch. and ...
Public Statistics
| Date Registered | 09-02-2010 02:52 AM |
| Date Last Visited | 08-18-2017 03:53 AM |
| Total Messages Posted | 13 |
