Good morning
I want to configure the Cisco 2811 E1 interface (VWIC2-1MFT-T1/E1) but i have a problem with the Alarm DEL (AL) witch it is always in yellow color.
The AL del is switch on just after i enter the first command router(config)# card type E1 0 1
the command sh controller E1 gives the result below
R-VOIP# sh controller E1
E1 0/1/0 is down.
Applique type is Channelized E1 - balanced
Cablelength is Unknown
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20080918, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (85 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 85 Unavail Secs
E1 0/1/1 is down.
Applique type is Channelized E1 - balanced
Cablelength is Unknown
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20080918, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (88 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 89 Unavail Secs
the command sh run gives the result below
R-VOIP# sh run
Building configuration...
Current configuration : 3010 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R-VOIP
!
boot-start-marker
boot-end-marker
!
card type e1 0 1
logging message-counter syslog
enable secret 5 $1$WjDK$Bxgi6CV6QYaMYIBBxpLzb/
!
no aaa new-model
no network-clock-participate wic 1
!
dot11 syslog
ip source-route
!
!
ip cef
ip dhcp excluded-address 10.0.0.1 10.0.0.10
!
ip dhcp pool MyPhones
network 10.0.0.0 255.255.255.0
option 150 ip 10.0.0.1
!
ip dhcp pool myphonesno
!
!
no ipv6 cef
!
multilink bundle-name authenticated
!
stcapp ccm-group 1
stcapp
!
!
!
!
!
!
voice service voip
allow-connections h323 to sip
allow-connections sip to h323
fax protocol cisco
h323
call start slow
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
voice-card 0
!
!
!
!
!
archive
log config
hidekeys
!
!
!
!
!
controller E1 0/1/0
!
controller E1 0/1/1
!
!
!
!
!
interface FastEthernet0/0
ip address 192.168.3.80 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0
no ip address
shutdown
no fair-queue
clock rate 125000
!
interface Serial0/0/1
no ip address
shutdown
clock rate 125000
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
!
!
!
!
!
!
!
control-plane
!
!
!
Can you tell me if this is normal or not?
I need to configure the Cisco 2811 E1 interface (VWIC2-1MFT-T1/E1) with the E1 line of Telecom provider
Another question, the router must be connected to the modem or just plug it directly to the E1 line of the Telecom provider ?
The interface VWIC2-1MFT-T1/E1 do the same functions like a modem or not?
thank a lot
