cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
153
Views
10
Helpful
4
Replies
Highlighted
Beginner

Radio0 not present 0 0 0 0 0 0 Aironet 1572

Hi, I'm reaching out to see if anyone has encountered this issue.

 

IOS Bootloader - Starting system.
flash is writable
40MB format
Cyprus MB -- 40MB of flash
Xmodem file system is available.
flashfs[0]: 24 files, 5 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 13406208
flashfs[0]: Bytes available: 27752448
flashfs[0]: flashfs fsck took 10 seconds.
Base Ethernet MAC address: a4:6c:2a:48:65:a0

port 5 Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/c1570-k9w8-mx.153-3.JD14/c1570-k9w8-mx.153-3.JD14"...#############################################
File "flash:/c1570-k9w8-mx.153-3.JD14/c1570-k9w8-mx.153-3.JD14" uncompressed and installed, entry point: 0x1003000
executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

 

Cisco IOS Software, C1570 Software (C1570-K9W8-M), Version 15.3(3)JD14, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Fri 23-Mar-18 15:40 by prod_rel_team

40MB format
Cyprus MB -- 40MB of flash
Initializing flashfs...

flashfs[2]: 24 files, 5 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 13406208
flashfs[2]: Bytes available: 27494400
flashfs[2]: flashfs fsck took 12 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCC
Copy in progress...CCCCCCCCCCC
Uncompressing radio files...
...done Initializing flashfs.

create idb =66E0218

vtu index 1 is created

vtu index 2 is created

vtu index 3 is created

vtu index 4 is created

vtu index 5 is created
eth_wait stop the ios now, need be changed to 0

Radio0 not present 0 0 0 0 0 0
Radio1 not present 0 0 0 0 0 4
No radios initialized!
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-AP1572EAC-A-K9 (PowerPC) processor (revision C0) with 376814K/134656K bytes of memory.
Processor board ID FGL1917Y04U
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.3.141.0
5 Gigabit Ethernet interfaces


32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address:
Part Number :
PCB Serial Number :
Top Assembly Part Number :
Top Assembly Serial Number :
Top Revision Number :
Product/Model Number : AIR-AP1572EAC-A-K9
% Please define a domain-name first.
fake phy int done idb =

 

Press RETURN to get started!


*Mar 1 00:00:15.847: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:16.187: Registering HW DTLS

*Mar 1 00:00:16.195: Non-Cable-Modem AP present
*Mar 1 00:00:17.059: idb 0 =9AEB1D4

*Mar 1 00:00:17.059: idb 1 =9AECC78

*Mar 1 00:00:17.059: idb 2 =9AEE86C

*Mar 1 00:00:17.059: idb 3 =9AF0460

*Mar 1 00:00:17.059: idb 4 =9AF2054
APAVC Registering AVC licences on the AP to make sure we enable advanced PP

*Mar 1 00:00:18.287: %LINK-6-UPDOWN: Interface Ethernet0, changed state to up
*Mar 1 00:00:18.447: Starting Ethernet promiscuous modeAPAVC Protocol list already initialized.

*Mar 1 00:00:18.715: Start STILE Activation
APAVC: Succeeded to activate all the STILE protocols.
APAVC: Registering with CFT

*Mar 1 00:00:18.963: APAVC: CFT registration of delete callback succeeded
APAVC: Reattaching Original Buffer pool for system use

*Mar 1 00:00:19.199: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:19.199: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:19.199: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:19.199: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:19.199: %LINK-6-UPDOWN: Interface GigabitEthernet4, changed state to up
*Mar 1 00:00:20.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:20.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar 1 00:00:20.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Mar 1 00:00:20.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Mar 1 00:00:20.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4, changed state to down
*Mar 1 00:00:21.591: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1570 Software (C1570-K9W8-M), Version 15.3(3)JD14, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Fri 23-Mar-18 15:40 by prod_rel_team
*Mar 1 00:00:21.591: %SNMP-5-COLDSTART: SNMP agent on host APa46c.2a48.65a0 is undergoing a cold startAstools: Could not initialize functionality

*Mar 1 00:00:22.907: The AVR image is up-to-date (1.0.0.31)

*Mar 1 00:00:22.911: change led intensity to 100 percent

*Mar 1 00:00:22.911: AVR module accelerometer initialized
*Mar 1 00:00:22.951: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:23.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:24.867: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set radio control and data rate
lwapp_crypto_init: MIC Present and Parsed Successfully

*Mar 1 00:00:25.027: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:29.399: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:29.399: DPAA Initialization Complete
*Mar 1 00:00:29.399: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:31.623: get_radio_temp input parameter wrong 0 radioidb =0x0

*Mar 1 00:00:31.623: get_radio_temp input parameter wrong 0 radioidb =0x0

*Mar 1 00:00:31.623: get_radio_temp input parameter wrong 1 radioidb =0x0

*Mar 1 00:00:31.623: get_radio_temp input parameter wrong 1 radioidb =0x0

*Mar 1 00:00:34.099: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:35.099: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:37.059: %DOT11-3-ADD_PRIM_IDB_TOLIST: can not add idb GigabitEthernet0 to the private list
*Mar 1 00:00:39.991: Currently running a Release Image

*Mar 1 00:00:40.015: Using SHA-2 signed certificate for image signing validation.
*Mar 1 00:00:40.103: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:41.059: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:41.643: Orientation: Changed to Horizontal
*Mar 1 00:00:42.059: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:45.967: AP image integrity check PASSED

*Mar 1 00:00:45.971: Non-recovery image. PNP Not required.

*Mar 1 00:00:45.983: Cert ISSUER (39): cn=Cisco Manufacturing CA SHA2,o=Cisco

*Mar 1 00:00:45.999: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
Not in Bound state.
*Mar 1 00:00:51.587: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.0.8.12, mask 255.255.255.0, hostname APa46c.2a48.65a0

%Error opening flash:/capwap-saved-config (No such file or directory)
%Error opening flash:/capwap-saved-config-bak (No such file or directory)
*Mar 1 00:00:56.015: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 0 CLI Request Triggered
*Mar 1 00:00:56.019: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:56.019: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:56.019: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:57.015: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (8.8.8.8)

*Mar 1 00:01:02.127: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set radio control and data rate

*Mar 1 00:01:13.215: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 9 14:57:11.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.8.1 peer_port: 5246
*Sep 9 14:57:12.399: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.8.1 peer_port: 5246
*Sep 9 14:57:12.399: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.8.1
*Sep 9 14:57:12.407: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.0.8.1:5246
*Sep 9 14:57:12.407: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 9 14:57:12.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.8.1 peer_port: 5246
*Sep 9 14:57:21.999: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 9 14:57:22.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.8.1 peer_port: 5246
*Sep 9 14:57:22.000: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:224 Connection 0xC9B9A98 is already there for this server port 5246, Deleting it. Number of connections: 1

*Sep 9 14:57:22.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.0.8.1:5246
*Sep 9 14:57:22.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.0.8.1:5246

 

Also, what are all these zeros, and why there is a 4 at the end of Radio1?

Radio0 not present 0 0 0 0 0 0
Radio1 not present 0 0 0 0 0 4

 

Thank you for helping me out

4 REPLIES 4
VIP Mentor

Re: Radio0 not present 0 0 0 0 0 0 Aironet 1572

MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
Not in Bound state.

 

It seems this AP came with mesh image. Therefore you have to add AP ethernet MAC address under (Security -> AP Policies -> Add -> 1572 Ethernet Mac Address [cert type MIC] -> click Add)

 

Then AP should get registered and then you can change it from Bridge mode to local & you can roleback above configuration.

 

If AP Radio issue persisting, I would suggest to upgrade WLC code to 8.5.151.0 & test it again (it is most likely a software bug)

 

HTH

Rasika

*** Pls rate all useful responses ***

Beginner

Re: Radio0 not present 0 0 0 0 0 0 Aironet 1572

I tried to upload the new firmware (8.5.151.0) but for some reason it says: LWAPP image version 8.3.141.0

How would you upload the firmware? maybe I am doing something wrong

 

Thank you

VIP Mentor

Re: Radio0 not present 0 0 0 0 0 0 Aironet 1572

First you need to register AP to WLC with current version.

Then you need to upgrade your WLC 8.5.151.0

 

HTH

Rasika

Beginner

Re: Radio0 not present 0 0 0 0 0 0 Aironet 1572

Figured out that the network card inside the AP is burned.

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards