Hello!
This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful.
Virtual Assistant- Discover support content and options for your gearSupport page index - Contains a ...
I happen to own a WAP150 access point legally imported to Israel, although by some reason it reports country code DE in Wi-Fi network announcements. Wrong country code causes a lot of compatibility issues with 802.11AC-standard devices. For example, ...
Currently there are challenges to finding firmware for our latest generation CBS switch portfolio. To properly locate via search firmware perform the following:
https://software.cisco.com/download/homeSearch on “Business 140” / “Business 145” / “Busi...
Hello Community, I have recently bought a Cisco WAP361 Wireless Access Point. I would like to have it remote powered acting as a PoE PD (LAN0) and I would like to remotely power a small 8-port Switch which required up to 5 W via PoE on LAN1. As I was...
Hi Allproblem - user has to re-authentication when passing from one AP to the next, from one floor to the next.Set up is WAP371 Cluster between 3 APs on 3 floors through a Single switch, it has a Single SSID and the endpoints can maintain connectivit...
I know a while back Cisco and Apple entered into a partnership where Cisco optimized some of their products for Apple users. We basically run on Apple equipment (Macs, iPads, iPhone/AirPods, Apple TVs, and Apple Watch, plus we're looking at trying ou...
Hi,Any chance anyone may have a copy of the latest instruction manual and Firmware for an SRP 541WGigabit Ethernet WAN.If not does anyone know what the latest firmware released version was?Thanks
Recently I installed a WAP571, however whatsapp (or instagram) has been running extremely slow since then.This is also only if I am connected via the AP.I installed the latest firmware, but unfortunately this didn't help.So it is 100% certain the Cis...
I have 5 - 240AC APs that I am configuring in a RLAN, not MESH. I want to disable the 2.4Gz radios on all of the APs. One AP is the Master. Is this possible? I can't seem to find a way to disable the radio like in the older APs. How to or confirma...
I have an xfinity X1 router, broadcasting wireless, and 2 WAP 371 all on same SSID. I have some coverage issues and purchased three 240AC to implement a mesh (i have three of them) and have a few questions before I get started: 1. It would be very ...
Hi All In the process of 'upgrading' from WAP571s to the new Small Business APs. We have a 240AC as our Master. All devices reconnected without issue except for the sole Android phone we have, which happens to be mine! Having spent days working it th...
Hello, I was reading the administration guide of CBW series, but haven´t found any information about airtime fairness feature. Is it currently supported? If note, does anyone know whether it will be available in a future release? Regards
There are seven WAP571-E-K9 V02 ( FW v1.1.0.3 ) on SG220-26P ( FW 1.1.4.8 ). When i setup first WAP ... create new cluster ... my SSIDs, login/password - all is done . When i expanse cluster with second WAP all is good too . When i add third WAP i se...
Hi all,I have a radio schedule that turns off Radio 1 (the 5 GHz radio) at 11pm but keeps Radio 2 (the 2.4 GHz) running. The same schedule turns Radio 1 back on around 8:30am.The problem is that when the 5 GHz radio turns off (or on), the 2.4 GHz rad...
HiIs it possible to "mesh" WAP561 access ponits together to get a large wifi network without cabling ? I'd like to connect one AP to my network and the install other access points linked together to extend this network without cabling. If this is pos...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: