Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Virtual Assistant- Discover support content and options for your gearSupport page index - Contains a ...
Forum Posts
Dear all I have a new cbw150ax-s unk access point. I have set a captive portal and test AAA authen with external radius. All work fine but there is no accounting send to my radius server. So I need to access ssh to use terminal and enable radius acco...
Hello everyone,I'm fairly new to the Cisco universe and hope you can help me with a problem I can't quite understand.A customer of mine has the following setup: Cisco C1111-4P router and a CBS 350 series Switch. He now wanted to connect two AX150 acc...
I am using 3 AX150 AP in the home environment (700sq.ft with 10-15 clients) and even with the default setting client keeps disconnecting and fails to do seamless roaming with FT enabled with wpa2. With wpa3 roaming doesn't even work. Earlier I was u...
Resolved! Cisco 150AX stuck at blink green loop
the ap suddenly stopped working and blinking green for a while, and return back to white and blink green again. Seems to be stuck in a boot loop. I think it could be caused by a damaged image when the AP could have been powered off due to a power tri...
Resolved! Cisco 150AX rebooting by itself
Dear all,Before one of my APs fails, it keeps rebooting unexpected at a specific time. at 01:20 UTC+8, I noticed my remaining AP also does that. its seems very weird to me as I clearly did not set any automation to my APs to perform self reboot. Luck...
Resolved! CBW 150AX stuck in boot loop
Hello everybody,I have a cluster of 6 CBW150AX access points, yesterday I was upgrading the firmware from version 10.5.2.0 to 10.6.2.0 and after the reboot one of the AP got stuck in a boot loop (the other five were updated correctly).The LED on the ...
Hello everyone,Recently I bought the AP cbw150ax (my first experience with Cisco), but whatever I do I did not manage to connect my MacBook Pro (M1 Pro, latest MacOs Ventura 13.0.1) to its WiFi.So, right after the unboxing (default preinstalled firmw...
Resolved! Cisco 150AX ap not recognising itself
so I was changing the region configuration on my ap. after the last edit, the ap no longer shows up on its own management page. the led is blinking Green Red off. This really seems weird to me. Any one knows what's going on with my ap?Thanks for any ...
Hello,Ive bought 3 AX150 to spread out my network to get to diffrent location and also manage multiple wlan. But im having issues when connected to a router where the AP dosnt wanna boot so i can access it. At best i mananaged to configure the primar...
Hi,Good day to everyone,I would like to seek anyone advise and assistance in regard to my current 3 Wireless AP ( Model : Cisco WAP 4410N) that has been noticed didn't switch over or roaming each other. The Wifi clients is stay connected to 1 AP even...
Hi Team, I have above switch N9K-C9236C and my end NIC card has 200GB card i want to do the connectivity between Switch to server to using splitter cable 2port 100Gb + 100GB switch side and next hope will be my NIC it has 200GB So which QSFP Module a...
Is there anyone who can help me download the latest firmware for the WAP321? It should be 1.0.6.7. This AP is beyond end of life and I can't find this fw on the Cisco support site.
Hello,I've tried on my own for too long to figure this out so looking for assistance please...My home network has FTTB providing 100 Mbps down and 40 Mbps up. Clients associated to the WAP371 (FW 1.3.0.7, the latest), however, get 0.5Mbps down and pi...
i have 4 CBW 240 that have issue with broadcasting 5g radio
Thank you for any help.Brand New Small Business installing 150 AX. 3 total. Can location/radio interference cause an issue?I have one location that will not obtain IP address(red,green,off) I can change the units (use different Access Points), take...
