06-14-2014 09:41 PM - edited 07-05-2021 01:00 AM
Hi Friends
Finally join and register 1602i (AIR-CAP1602i-E-k9) to 3850 (WS-C3850-24T) WLC
Now connect registered 1602i to WS-C2960-24PC-L that C2960 & C3850 trunk together, but again the 1602i not join ! (log below)
When Connect access port of two devices (C2960 & C3850) together and 1602i connect to another access port of C2960, 1602i join & registered !
Really can't use Aps in another branch far from C3850 WLC ?!
AP1602i#
*Jun 15 05:03:51.566: %CAPWAP-3-ERRORLOG: Selected MWAR 'Ctrl1'(index 0).
*Jun 15 05:03:51.566: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 15 05:03:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.188.22 peer_port: 5246
*Jun 15 05:03:51.291: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.188.22 peer_port: 5246
*Jun 15 05:03:51.291: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22
*Jun 15 05:04:09.663: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceed., 1)x(UNKNOWN_MESSAGE_TYPE (5)
*Jun 15 05:04:09.663: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jun 15 05:04:09.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.188.22:5246
*Jun 15 05:04:09.715: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jun 15 05:04:09.739: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jun 15 05:04:09.739: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jun 15 05:04:09.743: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 15 05:04:09.779: %CAPWAP-3-STATIC_TO_DHCP_IP: Could not discover WLC using static IP. Forcing AP to use DHCP.
*Jun 15 05:04:09.795: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 15 05:04:10.743: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 15 05:04:10.775: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jun 15 05:04:10.783: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jun 15 05:04:11.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jun 15 05:04:11.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jun 15 05:04:11.807: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 15 05:04:11.815: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jun 15 05:04:11.823: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jun 15 05:04:12.807: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jun 15 05:04:12.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 15 05:04:12.859: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 15 05:04:13.859: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
C3850#
Jun 15 05:02:03.631: *%LWAPP-3-VALIDATE_ERR: 1 wcm: Validation of SPAM Vendor Specific Payload failed - AP c0:25:5c:96:90:e0
*Jun 15 05:02:03.632: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.
*Jun 15 05:02:03.634: *%LOG-3-Q_IND: 1 wcm: Validation of SPAM Vendor Specific Payload failed - AP c0:25:5c:96:90:e0
*Jun 15 05:02:03.634: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm: Failed to create CAPWAP data tunnel with interface id: 0xf584c00000000b for AP: c025.5c96.90e0 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.
*Jun 15 05:02:21.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination
*Jun 15 05:02:31.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]
*Jun 15 05:02:41.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 2 times/sec!.]
*Jun 15 05:02:51.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]
*Jun 15 05:03:01.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 2 times/sec!.]
*Jun 15 05:03:11.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]
*Jun 15 05:03:21.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 2 times/sec!.]
*Jun 15 05:03:31.755: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]
*Jun 15 05:03:32.590: *%LOG-3-Q_IND: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination
*Jun 15 05:03:32.591: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event () and state (CAPWAP Join Response) combination
*Jun 15 05:03:41.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination
*Jun 15 05:04:02.419: *%LOG-3-Q_IND: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 3 times.!]
*Jun 15 05:04:02.419: *%LWAPP-3-VALIDATE_ERR: 1 wcm: Validation of SPAM Vendor Specific Payload failed - AP c0:25:5c:96:90:e0
*Jun 15 05:04:02.420: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.
*Jun 15 05:04:02.420: *%LOG-3-Q_IND: 1 wcm: Validation of SPAM Vendor Specific Payload failed - AP c0:25:5c:96:90:e0
*Jun 15 05:04:02.421: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm: Failed to create CAPWAP data tunnel with interface id: 0xcbe4000000000c for AP: c025.5c96.90e0 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.
*Jun 15 05:04:20.545: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm: Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination
Solved! Go to Solution.
06-15-2014 09:13 AM
Hi,
Yes, APs must be directly connected to the 3850 for it to work in MA or MC mode.Now better to use 3850 switch only for wired network and better to buy 5500 series WLC then you can use Hreap/flex-connect to connect several branch.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/81680-hreap-modes.html
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/71250-h-reap-design-deploy.html
Regards
Dont forget to rate helpful posts
06-14-2014 11:58 PM
Now connect registered 1602i to WS-C2960-24PC-L that C2960 & C3850 trunk together, but again the 1602i not join !
Won't work. The AP has to be DIRECTLY-CONNECTED to the 3850 switch.
06-15-2014 12:39 AM
Dear Leo ...
I bought several AP1206i & one 3850 for several branch. What do i do?
06-15-2014 09:13 AM
Hi,
Yes, APs must be directly connected to the 3850 for it to work in MA or MC mode.Now better to use 3850 switch only for wired network and better to buy 5500 series WLC then you can use Hreap/flex-connect to connect several branch.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/81680-hreap-modes.html
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/71250-h-reap-design-deploy.html
Regards
Dont forget to rate helpful posts
06-15-2014 10:12 PM
Hi Dear Sandeap;
Ok, got it!
Please help me, please
Without thinking I bought 3 AIR-CAP1602i & WS-C3850-24T-L whit 50 license !
I Wanted to install APs in different site and install WLC in ISP.
Now pleas say to me exactly what do i do?
What are devices (APs & WLC) have to buy that has useful for expansion?
I have Several campuses that connect to ISP whit Fiber or P2P Wireless & must install AP's in these campuses for students an master's. My Switches C2960 series and most of them have not 802.1Q ...
06-15-2014 11:22 PM
Air CAP 1602i will work as remote AP in flexconnect.
Yes you can install WLC(Cisco Flex 8500 and 7500, Cisco 5500, 4400, and 2500 Series Controllers) on HQ site.
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112042-technote-product-00.html
1. For flexconnect you must have a WAN connection from HQ to remote site(I think you have it).
2. Then you can connect AP at remote site and WLC ate main site.
3. Here is the links, how to configure flexconnect:
https://supportforums.cisco.com/document/98646/wireless-lan-flexconnect-configuration-example
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-2/configuration/guide/cg/cg_flexconnect.html
Hope it helps.
Regards
Dont forget to rate helpful posts
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide