cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3139
Views
20
Helpful
11
Replies

1310 LAP unable to join WLC 5508

ahmedbishry
Beginner
Beginner

Hi All,

Hope to you a very happy new year,

I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error,

I get this error from the LAP 1310 console as below:

Compiled Mon 17-Jul-06 11:45 by alnguyen

*Mar  1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

*Mar  1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

*Mar  1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Mar  1 00:00:33.477: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.25, mask 255.255.255.0, hostname APe4d3.f1c2.8882

examining image...

*Mar  1 00:00:44.781: %LWAPP-5-CHANGED: LWAPP changed state to JOIN

*Jan 11 15:21:37.178: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE

%Error opening  (Protocol error)archive download: takes 6 seconds

*Jan 11 15:21:43.178: LWAPP_CLIENT_ERROR_DEBUG:  Retransmission count for packet exceeded more than max(IMAGE_DATA

, 1)

*Jan 11 15:21:43.178: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Jan 11 15:21:43.179: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Jan 11 15:21:43.181: LWAPP_CLIENT_ERROR: not receive read response(3)

*Jan 11 15:21:43.185: lwapp_image_proc: unable to open tar file

*Jan 11 15:21:43.200: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.

*Jan 11 15:21:43.201: %LWAPP-5-CHANGED: LWAPP changed state to DOWN

*Jan 11 15:21:43.207: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.

flashfs[0]: 3 files, 2 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 7741440

flashfs[0]: Bytes used: 1861632

flashfs[0]: Bytes available: 5879808

flashfs[0]: flashfs fsck took 14 seconds.

Base ethernet MAC Address: e4:d3:f1:c2:88:82

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Loading "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx"...#######################################################################################################################################################################

File "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000

executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 17-Jul-06 11:45 by alnguyen

Image text-base: 0x00003000, data-base: 0x00359EA0

Initializing flashfs...

flashfs[1]: 3 files, 2 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 7741440

flashfs[1]: Bytes used: 1861632

flashfs[1]: Bytes available: 5879808

flashfs[1]: flashfs fsck took 2 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

cisco AIR-LAP1310G-E-K9R   (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.

Processor board ID FGL1649T00U

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from reload

LWAPP image version 3.0.51.0

1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: E4:D3:F1:C2:88:82

Part Number                          : 73-8960-09

PCA Assembly Number                  : 800-24963-06

PCA Revision Number                  : B0

PCB Serial Number                    : FOC16447J1K

Top Assembly Part Number             : 800-28479-05

Top Assembly Serial Number           : FGL1649T00U

Top Revision Number                  : D0

Product/Model Number                 : AIR-LAP1310G-E-K9R

Press RETURN to get started!

*Mar  1 00:00:04.329: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 17-Jul-06 11:45 by alnguyen

*Mar  1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

*Mar  1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

*Mar  1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Mar  1 00:00:33.352: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.28, mask 255.255.255.0, hostname APe4d3.f1c2.8882

examining image...

*Mar  1 00:00:44.783: %LWAPP-5-CHANGED: LWAPP changed state to JOIN

*Jan 11 15:21:37.189: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE

%Error opening  (Protocol error)archive download: takes 6 seconds

*Jan 11 15:21:43.189: LWAPP_CLIENT_ERROR_DEBUG:  Retransmission count for packet exceeded more than max(IMAGE_DATA

, 1)

*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Jan 11 15:21:43.192: LWAPP_CLIENT_ERROR: not receive read response(3)

*Jan 11 15:21:43.195: lwapp_image_proc: unable to open tar file

*Jan 11 15:21:43.210: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.

*Jan 11 15:21:43.210: %LWAPP-5-CHANGED: LWAPP changed state to DOWN

*Jan 11 15:21:43.216: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.

flashfs[0]: 3 files, 2 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 7741440

flashfs[0]: Bytes used: 1861632

flashfs[0]: Bytes available: 5879808

flashfs[0]: flashfs fsck took 14 seconds.

Base ethernet MAC Address: e4:d3:f1:c2:88:82

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Please Advise,

Thanks in advanced,

Ahmed,

1 Accepted Solution

Accepted Solutions

Usually the release notes keep saying that it is not supported, but actually I never had a problem with it.

Of course you will lose all the configuration that is specific to 7.2, and you could run into problems if you are using flexconnect settings, because before 7.2 this feature used to be called hreap.

So I strongly recommend to backup your configuration before doing the downgrade. If your configuration is not too complex, it could be a good idea to do the upgrade, reset your wlc to factory settings, and reconfigure your controller.

regards

Stefan

View solution in original post

11 Replies 11

stefan.angerer
Beginner
Beginner

Ahmed,

on which code version is your 5500 running?

The 1300 bridges are only supported until 7.0.x as you can see in the WLC release notes:

http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn73.html#wp976967

regards

Stefan