9800-CL on Nutanix

[thenetadmin]

Hi,

Does 9800-CL wireless controller will work on Nutanix? I didn't find any official supporting document.

[marce1000]

                                  - If an underlying supported hypervisor is being used then it will work :
          Ref : https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9800-cl-wireless-controller-cloud/nb-06-cat9800-cl-cloud-wirel-data-sheet-ctp-en.html (Table 2)
>...

Hypervisors and cloud providers supported

ESXi 6.0/6.5/6.7, KVM, Hyper-V, NFVIS

ESXi 6.0/6.5/6.7, KVM, Hyper-V, NFVIS

ESXi 6.0/6.5/6.7, KVM, Hyper-V, NFVIS

AWS, GCP, Azure

AWS, GCP, Azure

AWS, GCP, Azure

 M.

[thenetadmin]

Thank you @marce1000 

KVM qcow2 images are supported on Nutanix. Does Cisco TAC will support if there are technical issues post deployment?

With vWLC 9800-CL with 300+ APs, any specific limitations or performance considerations, I should be aware of when scaling to this size.

Any caveats with specific features?Any limitation on throughput?

[marce1000]

   >...Does Cisco TAC will support if there are technical issues post deployment?
                 -If a supported environment is being used : yes 

  >...With vWLC 9800-CL with 300+ APs, any specific limitations or performance considerations, I should be aware of when scaling to this size.
  Ref : https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9800-cl-wireless-controller-cloud/nb-06-cat9800-cl-cloud-wirel-data-sheet-ctp-en.html
   - Start reading from : Cisco Catalyst 9800-CL for private cloud  to get  an idea of performance and throughput parameters

                       >...Any caveats with specific features?Any limitation on throughput?
              - I have no Nutanix specific info's on that , perhaps discuss with a local reseller , 

 M.

[marce1000]

 - Beside earlier replies I would also like to point out that the various 9800-CL images can be downloaded without a service contract ; that give you the opportunity to test a basic deployment of for instance a qcow2 image on Nutanix.   Check if you can get a deployment and or installation started without fatal hazards. It's a good check to start with , 

 M.

[thenetadmin]

Is it still valid that 9800-CLs in an HA SSO need to be on the same physical host?

[marce1000]

    - They don't but there are advanced gotchas that may come up if they are not on the same physical host ; such as that the in between switches must use the same vlan tagging , for the various networks (vlans/subnets)  defined in the controllers , 

 M.

[SlaSla]

Hi,

have you been able to successfully deploy a 9800-CL on Nutanix-AHV at the end?

I understand that AHV supports .qcow2 as it´s based on KVM.

I have to migrate a 9800-CL HA pair from Nutanix-VmWare to Nutanix-AHV  and any experiences from the community would be highly appreciated.

For me it would be interesting to know, if there is a way for migrating the VMs from Vmware to AHV or do I need

to do a fresh install and importing the configuration?

Thanks

Steven

[marce1000]

 - @SlaSla I don't think Nutanix is supported because it is not mentioned in https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/technical-reference/c9800-cl-dg.html

    + Anyway if there is a business dependence then consider creating a TAC case and asking the question mandatory.
      So you can have an authoritative answer from Cisco (too)

  M.