The time output of the WLC:
(Cisco Controller) >show time
Time............................................. Thu Jul 14 15:07:23 2022
Timezone delta................................... 0:0
Timezone location................................ (GMT +2:00) Jerusalem
NTP Servers
NTP Polling Interval......................... 86400
Index NTP Key Index NTP Server NTP Msg Auth Status
------- ----------------------------------------------------------------------------------
1 0 192.168.12.10 AUTH DISABLED
2 0 192.168.12.10 AUTH DISABLED
The output from bootup:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.07.14 15:05:19 =~=~=~=~=~=~=~=~=~=~=~=
*Jul 14 12:05:19.447: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.100
*Jul 14 12:05:19.447: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.100
*Jul 14 12:05:19.447: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.100:5246
AP78da.6e59.ad08#relo
AP78da.6e59.ad08#reload
Proceed with reload? [confirm]
Writing out the event log to flash:/event.log ...
*Jul 14 12:05:24.567: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 11
*Jul 14 12:05:24.567: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 11
*Jul 14 12:05:24.575: %SYS-5-RELOAD: Reload requested by cisco on console. Reload Reason: Reload.
*Jul 14 12:05:24.575: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
Write of event.log done
Not in Bound state.
*Jul 14 12:05:29.467: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
System Bootstrap, Version U-Boot 1.1.4-gf5ee82b1-dirty Corfu , RELEASE SOFTWARE
Build Date: Oct 17 2013 - 18:08:55
corfu - Scorpion 1.0
DRAM: 256 MB
Now running in RAM - U-Boot at: 8ffbc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x14
flash size 1MB, sector count = 256
Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.
Ath Nand ID[8ffee17c]: 2c:f1:80:95:02
ONFI MICRON MT29F1G08ABADAWP
Micron NAND 128MiB 3,3V 8-bit [128MB]
size = 128MB
Hit any key to stop autoboot: 5 4 3 2 1 0
boot_method is set to IOS_BOOT, boot IOS bootloader in NOR flash
Loading .text @ 0x84000000 (207840 bytes)
Loading .rodata @ 0x84032be0 (39008 bytes)
Loading .data @ 0x8403c440 (3264 bytes)
Loading .data.rel.local @ 0x8403d100 (1084 bytes)
Loading .data.rel @ 0x8403d53c (124 bytes)
Loading .data.rel.ro @ 0x8403d5b8 (960 bytes)
Clearing .bss @ 0x8403d980 (161116 bytes)
Clearing .scommon @ 0x84064edc (56 bytes)
## Starting application at 0x84000000 ...
IOS Secondary Bootloader - Starting system.HW Test Status(0)
Ath Nand ID: 95:80:f1:2c:00
Using driver version 1 for media type 2
Valid buffers 315
total315 315
success found all blocks
start end 16 74
found in range
high low end 2384 515 74
Xmodem file system is available.
mifs[0]: 24 files, 5 directories
mifs[0]: Total bytes : 131334144
mifs[0]: Bytes used : 16533504
mifs[0]: Bytes available : 114800640
mifs[0]: mifs fsck took 0 seconds.
Base Ethernet MAC address: 78:da:6e:59:ad:08
Setup MAC....
Waiting for PHY auto negotiation to complete...Port 0 Negogiation success.
Ethernet speed is 1000 Mb - FULL duplex
Scorpion ----> F1 PHY *
: cfg1 0xf cfg2 0x7215
Loading "flash:/ap1g3-k9w8-mx.153-3.JK7/ap1g3-k9w8-mx.153-3.JK7"...##############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/ap1g3-k9w8-mx.153-3.JK7/ap1g3-k9w8-mx.153-3.JK7" uncompressed and installed, entry point: 0x60080000
executing...
Stop MAC.
Starting IOS...
cp0 timer begin value is set as 1000
prid= 19750
Starts main.
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1530 Software (ap1g3-K9W8-M), Version 15.3(3)JK7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
Compiled Sat 26-Feb-22 07:36 by mcpre
Initializing flashfs...
Ath Nand ID: 95:80:F1:2C:00
Using driver version 1 for media type 2
Valid buffers 315
total315 315
success found all blocks
start end 16 74
found in range
high low end 2384 515 74
mifs[3]: 24 files, 5 directories
mifs[3]: Total bytes : 131334144
mifs[3]: Bytes used : 16533504
mifs[3]: Bytes available : 114800640
mifs[3]: mifs fsck took 5 seconds.
mifs[3]: Initialization complete.
...done Initializing flashfs.
:pci_init_board:521 *** Warning *** : PCIe1 WLAN Module not found !!!
pci_rc2_init_board:570 PCIE Controller Init Bus Master Enable
:pci_rc2_init_board:593 PCIe2 WLAN Module Found !!!
soap_pci_subsys_init:706 Bus Master/Mem Enable on pci_write side
soap_pci_subsys_init(713): PCI vendor ID: 0x168C ret:0
soap_pci_subsys_init(715): PCI device ID: 0x33 ret:0
Scorpion ----> F1 PHY *
Waiting for PHY auto negotiation to complete...Port 0 Negogiation success.
Disabling 802.3az feature on port 0
sgmii cal value = 0xE
Disabling 802.3az feature on port 1.
SGMII setup done, status is 0x1
Radio0 present 9550 9000 0 0 0 0
Rate table has 282 entries (12 legacy/96 11n/174 11ac)
Radio1 present 9590 9000 0 0 B2000000 1
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-CAP1532I-E-K9 (MIPS74k) processor (revision 24) with 204800K/57344K bytes of memory.
Processor board ID FCZ1752H01T
MIPS74k CPU at 700Mhz, revision number 0x0000
Last reset from power-on
LWAPP image version 8.10.171.0
2 Gigabit Ethernet interfaces
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 78:DA:6E:59:AD:08
Part Number : 74-11942-01
PCB Serial Number : FOC174549GR
Top Assembly Part Number : 000-00000-00
Top Assembly Serial Number : FCZ1752H01T
Top Revision Number : 23
Product/Model Number : AIR-CAP1532I-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.583: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)mips74k_config_radio_pci(302): PCI CMD write: 0x356
*Mar 1 00:00:25.159: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to upEnterprise mode: 0x44000000
*Mar 1 00:00:25.659: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (2)
*Mar 1 00:00:25.735: ath_load_ctl_pwr_tbl() dot11radio 2G loading CTL binary flash:/ap1g3-k9w8-mx.153-3.JK7/CO2.bin version# 7.6
*Mar 1 00:00:26.239: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (2)
*Mar 1 00:00:26.239: ath_load_ctl_pwr_tbl() dot11radio 5G loading CTL binary flash:/ap1g3-k9w8-mx.153-3.JK7/CO5.bin version# 1.2
*Mar 1 00:00:27.159: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:29.647: CDP_PD: Power Source: 2-pair Power Injector
APAVC Registering AVC licences on the AP to make sure we enable advanced PP
*Mar 1 00:00:31.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:32.991: SCHED: Ethernet Bridge Process: install watched boolean System Initialized(633B2014), os:1 ah:0APAVC Protocol list already initialized.
*Mar 1 00:00:32.991: Start STILE Activation
APAVC: Succeeded to activate all the STILE protocols.
APAVC: Registering with CFT
*Mar 1 00:00:33.395: APAVC: CFT registration of delete callback succeeded
APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:00:33.623: Found crash file: 'crashinfo_19930301-004058-UTC'
*Jul 14 12:05:24.191: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 39
*Jul 14 12:05:24.191: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 39
*Jul 14 12:05:24.211: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1530 Software (ap1g3-K9W8-M), Version 15.3(3)JK7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
Compiled Sat 26-Feb-22 07:36 by mcpre
*Jul 14 12:05:24.211: %SNMP-5-COLDSTART: SNMP agent on host AP78da.6e59.ad08 is undergoing a cold start
*Jul 14 12:05:24.263: SCHED: Ethernet Bridge Process: remove watched boolean System Initialized(633B2014)
*Jul 14 12:05:24.263: SCHED: Ethernet Bridge Process: install watched queue Soap BVI input queue(665F873C), os:0 ah:0
*Jul 14 12:05:24.367: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Jul 14 12:05:24.367: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Jul 14 12:05:24.367: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
*Jul 14 12:05:24.391: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - EASY_ADMIN is not set, turn off easy admin service!
*Jul 14 12:05:24.391: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - Easy Admin is not enabled, turn it off!
*Jul 14 12:05:24.415: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 39
*Jul 14 12:05:24.415: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 39
*Jul 14 12:05:24.455: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Jul 14 12:05:24.471: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10lwapp_crypto_init: MIC Present and Parsed Successfully
*Jul 14 12:05:25.967: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Jul 14 12:05:33.883: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.19, mask 255.255.255.0, hostname AP78da.6e59.ad08
*Jul 14 12:05:42.643: Currently running a Release Image
validate_sha2_block: Failed to get certificate chain
*Jul 14 12:05:42.647: Using SHA-1 signed certificate for image signing validation.%Default route without gateway, if not a point-to-point interface, may impact performance
*Jul 14 12:05:53.763: AP image integrity check PASSED
*Jul 14 12:05:53.779: Non-recovery image. PNP Not required.
*Jul 14 12:05:53.799: validate_sha2_block:No SHA2 Block present on this AP.
*Jul 14 12:05:53.839: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 14 12:05:54.839: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jul 14 12:05:54.847: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jul 14 12:05:55.839: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jul 14 12:05:55.907: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jul 14 12:05:56.907: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%Error opening flash:/capwap-saved-config (No such file or directory)
%Error opening flash:/capwap-saved-config-bak (No such file or directory)
%Error opening flash:/pnp-saved-config (No such file or directory)
no ip http secure-server
^
% Invalid input detected at '^' marker.
*Jul 14 12:06:03.883: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 0 CLI Request Triggered
*Jul 14 12:06:04.883: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 started - CLI initiated
User Access Verification
Username:
Username:
Username: %No matching route to delete
Translating "CISCO-CAPWAP-CONTROLLER.fts.local"...domain server (192.168.3.60)
*Jul 14 12:07:39.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.99 peer_port: 5246
*Jul 14 12:07:40.459: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.99 peer_port: 5246
*Jul 14 12:07:40.459: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.99
*Jul 14 12:07:45.459: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.99
*Jul 14 12:07:45.459: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.99
*Jul 14 12:07:45.459: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.99:5246
*Jul 14 12:07:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.100 peer_port: 5246
*Jul 14 12:07:45.471: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.100 peer_port: 5246
*Jul 14 12:07:45.471: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.100
*Jul 14 12:07:50.471: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.100
*Jul 14 12:07:50.471: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.100
*Jul 14 12:07:50.471: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.100:5246
*Jul 14 12:07:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.99 peer_port:
