Solved: Re: AIR-LAP1242AG-A-K9 Cannot Join to WLC - Page 3

arika_wahyono · ‎02-20-2014

Guys,

I have problem, i try to connect AP AIR-LAP1242AG-A-K9 to WLC 4400 with Software 7.0.98.218, but the AP indicator is blink and always request new IP addres (based on AP logg console), this device can ping from LAN but unstable (based on logg, the AP always request new IP Address).

anyone have any had same experience with this case?

This is log when i try console to AP.

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Xmodem file system is available.

flashfs[0]: 15 files, 4 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 15998976

flashfs[0]: Bytes used: 10084864

flashfs[0]: Bytes available: 5914112

flashfs[0]: flashfs fsck took 36 seconds.

Base ethernet MAC Address: 00:1d:45:36:86:ca

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Loading "flash:/c1240-k9w8-mx.124-23c.JZ/c1240-k9w8-mx.124-23c.JZ"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/c1240-k9w8-mx.124-23c.JZ/c1240-k9w8-mx.124-23c.JZ" uncompressed and installed, entry point: 0x3000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Wed 06-Apr-11 15:01 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

flashfs[1]: 15 files, 4 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15740928

flashfs[1]: Bytes used: 10084864

flashfs[1]: Bytes available: 5656064

flashfs[1]: flashfs fsck took 5 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

Radio0 present A506 7100 E8000000 A0000000 80000000 3

Radio1 present A506 6700 E8000100 A0040000 80010000 2

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-LAP1242AG-A-K9 (PowerPCElvis) processor (revision A0) with 25590K/7168K bytes of memory.

Processor board ID FTX1135B3ZF

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from power-on

LWAPP image version 7.0.98.218

1 FastEthernet interface

2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: xxxxxxxxxx

Part Number : 73-9925-06

PCA Assembly Number : 800-26579-05

PCA Revision Number : xxxxx

PCB Serial Number : xxxxxxx

Top Assembly Part Number : xxxxxxx

Top Assembly Serial Number : xxxxxxx

Top Revision Number : A0

Product/Model Number : AIR-LAP1242AG-A-K9

% Please define a domain-name first.

Press RETURN to get started!

*Mar 1 00:00:06.526: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed

*Mar 1 00:00:08.150: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0

*Mar 1 00:00:09.747: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1

*Mar 1 00:00:09.863: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar 1 00:00:09.895: status of voice_diag_test from WLC is false

*Mar 1 00:00:12.004: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

*Mar 1 00:00:12.072: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Wed 06-Apr-11 15:01 by prod_rel_team

*Mar 1 00:00:12.072: %SNMP-5-COLDSTART: SNMP agent on host AP001d.4536.86ca is undergoing a cold start

*Mar 1 00:00:12.154: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar 1 00:00:12.161: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Mar 1 00:00:12.161: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Mar 1 00:00:12.369: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar 1 00:00:13.016: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

*Mar 1 00:00:13.170: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

*Mar 1 00:00:13.170: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Mar 1 00:00:20.493: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

*Mar 1 00:00:30.976: status of voice_diag_test from WLC is false

*Mar 1 00:00:31.083: Logging LWAPP message to 255.255.255.255.

*Mar 1 00:00:34.263: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

*Mar 1 00:00:34.304: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up

*Mar 1 00:00:34.342: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Mar 1 00:00:35.265: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up

*Mar 1 00:00:35.265: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated

*Mar 1 00:00:35.304: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar 1 00:00:42.131: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:00:42.135: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar 1 00:00:42.139: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar 1 00:01:32.143: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

*Mar 1 00:01:34.274: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

Not in Bound state.

*Mar 1 00:01:40.659: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar 1 00:01:40.778: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar 1 00:01:48.652: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:01:48.655: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar 1 00:01:48.657: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar 1 00:02:28.661: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar 1 00:02:37.173: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar 1 00:02:37.290: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar 1 00:02:45.164: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:02:45.167: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar 1 00:02:45.169: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar 1 00:03:25.170: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar 1 00:03:33.681: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar 1 00:03:33.798: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar 1 00:03:41.673: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:03:41.676: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar 1 00:03:41.678: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar 1 00:04:21.679: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar 1 00:04:30.191: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar 1 00:04:30.308: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar 1 00:04:38.181: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:04:38.184: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar 1 00:04:38.187: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar 1 00:05:18.191: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar 1 00:05:26.703: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar 1 00:05:26.820: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar 1 00:05:34.694: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:05:34.696: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar 1 00:05:34.699: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROL

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Thanks!!!

manassin · ‎03-06-2014

Hi Arika,

The AP is using the DNS option to join the WLC.

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar 1 00:00:42.135: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar 1 00:00:42.139: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

So in this case it seems that the AP is not able to join the WLC using dns.

Please run the following debugs on the WLC:

Controller>debug mac address

Controller>debug pm pki enable

Thanks and regards,

Manas Pratap Singh.