Hello,
I have AP 1242AG with corrupted image i have reset to factory setting using the mode button but it keeps booting and freezes at executing....
I have clicked ESC button to enter ap: command prompt but nothing happens here's the output:
Xmodem file system is available.
flashfs[0]: 149 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 6404096
flashfs[0]: Bytes available: 9594880
flashfs[0]: flashfs fsck took 29 seconds.
Base ethernet MAC Address: 00:1f:ca:26:53:88
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button is pressed, wait for button to be released...
button pressed for 28 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1240-k9w7
-tar.default
examining image...
%Error opening ĀæĆæĆæĆæĆæĆæĆæĆ¾ĆæĆæĆæĆ½ĆæĆæĆ»Ć¾ĆæĆæƶƻĆæĆæĆÆĆæĆæĀæĆĆæĆæĆæĀæĆ·ĆæĆæĆ»ĆæĆ¾ĆæĆæĆæĆ½ĆæĆæĆæĆ»ĆæĆæĆæĆ·ĆæĆ¾ĆæĆÆĆæĆ»ĆæĆĆæĆæĆæĀæĆæĆ·ĆæĆæ
Ć¾~ĆæĆæĆ¾Ć½ĆæĆæĆæĆ»ĆæĆæĆæƧĆæĆæĆæoĆæĆæĆ¾ĆĆæĆæĆæĀæĆæĆæĆæĆæĆæĆ¾ĆæĆæĆæĆ¹ĆæĆæĆæĆ»ĆæĆæĆæƶĆæĆæĆæƧĆæĆæĆæĆĆÆĆæĆæĀæĆæĆæĆæĆæĆæĆæĀµLĀŖEĀ½-ĆĆ½ā¢[žĆŖ
i K2\*Ā¹*āĆĀ»Ćø#tāĀ²iTĀŗhĆø$<Å<Ć0E7ƵSdĆŗƬĆĆĀ²+Ć)āĆĀ»Ć«LR{āĆ”ÅøidĆYāĆĀŗKĆĀÆĆĆOā\2T/ĆĆX
EĀµĆĀ¶Ā²]@|Āŗ=6\6l:nĀ¶ā¦9lwĆ (connection timed out)Loading "flash:/c1250-k9w7-mx.124-1
0b.JDA3/c1250-k9w7-mx.124-10b.JDA3"...##########################################
################################################################################
################################################################################
########
File "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3" uncompressed
and installed, entry point: 0x3000
executing...
The main problem for me is that i can't access the ap command line to install a new image.
Any help please?
