Is there a Design Guide out for the IW3700? I need to know outdoor distances vs. throughput. I don't even see it in the Outdoor calculator yet.Thanks in advance,Nir
Is there a Design Guide out for the IW3700? I need to know outdoor distances vs. throughput. I don't even see it in the Outdoor calculator yet.Thanks in advance,Nir
Hello, I've a project to implement Meraki APs in an enterprise but I am new to Meraki. Their documentation mentioned the following " Because a Meraki AP can be sending/receiving tagged data traffic as well as untagged management traffic, all Meraki ...
hi, i started big report in mse 10.2. this report load memory and mse is not responding. can i delete report from cli? thank you
we have a local sports complex that had 4 existing 1320 ap,s mounted on field lighting poles. with pelco ip cameras connected to three of the ap,s.they are configured with one root bridge and 3 non root bridges, all in autonomous mode. we recently ad...
I know the 8510 is suppose to support 6000 APs and 65,000 clients. Does anyone know if Cisco has released any information based on throughput. The reason I ask is because with 4300 APs and 32,000 clients we are seeing an average of over 150ms ping ...
I have a client who has been using Meraki MR18 and MR34 Access point with Cisco Meraki controller for guest traffic . 1) I want to know if MR 18 and MR 34 are compatible with Cisco WLC 5508 . 2) Can a AP have two controller . Need here is to have 1 ...
Hi, i configured custom page on mse 10.2 as http://www.cisco.com/c/en/us/td/docs/wireless/mse/10-2/cmx_config/b_cg_cmx102/b_cg_cmx102_chapter_0100.html visitor login is redirected to portal, but custom portal content is not depicted, device screen ...
Hi all, I am in the process of setting up a 2504 with ap's.. With regards to connection, would it be ok to just plug the controller direct into the (Lynksys unmanaged) switch and then the controller would get its IP address from the Ubiquiti router...
Where to find following technologies for Cisco wireless access points? ssid, os version, wids, bonjur gateway, device fingerprnting, meshing, hotspot, mountimg
Hi All, I have 4 units of AIR-CAP2602I-A-K9 cisco aironet. I need to configure this AP to Radius server configurations. 1. All 4 units same SSID. 2. This 4 units of will be deploy to different locations. 3. This 4 units only one vlan 4. Radius se...
Hi Is there a relation between rogue access point detection and clean air , Rogue access point detection is based on the clean air technology ?
Hi Team, I just added an AP to my WLC through "Capwap ap controller ip XX" by using Default Username and Password..."Cisco and Cisco". 1. But is it possible to access my LAP through Telnet / SSH/Https after adding it to WLC. and how? 2. I am unabl...
This thread was opened two years ago but it received no replies so hoping someone can help! I have setup a new Guest Wlan on our vWLC ( AIR-CTVM-K9 ). Its a in a separate subnet and VLAN and I have DHCP proxy enabled. IP helper-address added to the ...
Guys and Girls, I am stumped here and don't know where to look. I have a 2504 that has port 1 plugged into a network (network A) using a 192 class C address scheme. Port 1 plugs into a 3560 that is then distributed to the rest of the network. I ha...
Hello, A scenario I hadn't run across before. The customer has an existing Foreign-Anchor WLC set up with their Guest WLAN running across it. They want the new BYOD service to do the same thing (not sure the point of it). When I anchor the WLAN to t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-16-2024 12:50 PM | ||
08-15-2024 04:04 PM | ||
07-25-2024 07:13 PM | ||
07-17-2024 11:11 AM | ||
07-17-2024 06:04 AM |
User | Count |
---|---|
15 | |
8 | |
5 | |
3 | |
3 |