Solved: C1852 Access Point Unable to Join Controller C5508

Tayyab831 · ‎07-27-2021

Dear All,

Greetings,

I am recently facing this problem my two 1852 APs are unable to join with controller. They were working fine for last six months but suddenly they are unable to join the controller. Below are given complete boot up process output,

U-Boot 2012.07 (btldr release 31) (Mar 15 2017 - 15:00:35)

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

DRAM: 1 GiB
NAND (ONFI): Detected SPANSION S34MS02G1 [256 MiB]
SF: Detected Macronix MX25U3235F [4 MiB]
MFG data loaded
Scanning shenv data blocks
Total valid parts=4
Active shenv part[1:1], write_counter=8
PCI0 Link Intialized
Net:
PHY ID = 0x4dd074, eth0 found AR8033 PHY
PHY ID = 0x4dd074, eth1 found AR8033 PHY
Valid I2C chip addresses: 51 52
AP 1832/1852 detected...
Power Type: 802.3af POE or Others detected...
Signature returns 0
BL signing verification success, continue to run...
Auto boot mode, use bootipq directly
Hit ESC key to stop autoboot: 0
Specified BOOT: part2

Booting from part2

Read 1024 bytes from volume part2 to 45000000
Read 23462495 bytes from volume part2 to 45000000
Signature returns 0
Image signing verification success, continue to run...
Using machid 0x1260 from environment

Starting image ...

[01/01/1970 00:00:00.0000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[01/01/1970 00:00:00.0000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[01/01/1970 00:00:00.0000] Machine: Cisco Systems 11ac Wave2 Wifi Access Point
[01/01/1970 00:00:00.0000] Memory policy: ECC disabled, Data cache writealloc
[01/01/1970 00:00:00.0000] Kernel command line: ubi.mtd=0 crashkernel=30M@1280M console=ttyHSL1,9600n8 activepart=part2 activeboot=0 wdgtriggered=0
[01/01/1970 00:00:00.1600] CPU1: Booted secondary processor
[01/01/1970 00:00:00.2300]
[01/01/1970 00:00:00.2300] +++ hydra_ap_gpio_value =3
[01/01/1970 00:00:08.8074] [sched_delayed] sched: RT throttling activated
[01/01/1970 00:00:18.8843] ACPU PVS: 1
[01/01/1970 00:00:19.9039] buginf tty flushing thread started, ttyport=eec0c290
[01/01/1970 00:00:24.5325] msm_hsusb_host msm_hsusb_host: unable to find transceiver
[*01/01/1970 00:00:24.7724] buginf() enabled.

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.

[*01/01/1970 00:00:24.7824] Made it into bootsh: Jun 4 2018 23:03:02
[*01/01/1970 00:00:24.7824] bootsh build T-5a1977b5600aa94dd31adcabae872ed6700b2ea1-g5a1977b5-vipendya
init started: BusyBox v1.23.2 (2018-06-04 22:46:06 PDT)
[*01/01/1970 00:00:27.8115] GCM-128 POST passed
[*01/01/1970 00:00:27.8115] GCM-256 POST passed
[*01/01/1970 00:00:28.0814] Active version: 8.3.143.0
[*01/01/1970 00:00:28.0814] Backup version: 8.2.151.0
[*01/01/1970 00:00:28.3013] AP1852I
Jan 1 00:00:28 FIPS[785]: *** shell: FIPS Mode = disabled ***

User Access Verification
Username: [*01/01/1970 00:00:28.4313] nss_driver - Turbo Support 1
[*01/01/1970 00:00:28.4313] Supported Frequencies - 110Mhz 550Mhz 733Mhz
[*01/01/1970 00:00:28.5512]
[*01/01/1970 00:00:28.5512] phy_value=0: org="0x1000" phy_reg="0x1800"
[*01/01/1970 00:00:28.9311] Current value of FACTORY_RESET=0
[*01/01/1970 00:00:28.9511] Last reload time: Jul 26 06:19:32 2021
[*07/26/2021 06:19:32.0000] Setting system time Mon Jul 26 06:19:32 UTC 2021
[*07/26/2021 06:19:32.0699]
[*07/26/2021 06:19:32.0699]
[*07/26/2021 06:19:32.0699] === 5G radio domain is 22, COPY 5G BDF files from non_ETSI_BDF folder ===
[*07/26/2021 06:19:32.0699]
[*07/26/2021 06:19:32.0699]
[*07/26/2021 06:19:32.1399] device wired0 entered promiscuous mode
[*07/26/2021 06:19:32.2399] device wired1 entered promiscuous mode
[*07/26/2021 06:19:32.6398] stile module dp init successfully
[*07/26/2021 06:19:32.6398] NBAR Label:BLD_MCP_DEV_LATEST_20150424_123021 NBAR VERSION:module build date: Oct 4 2017 at 08:58:38
[*07/26/2021 06:19:33.2196] miibus get eec4b000!
[*07/26/2021 06:19:33.2496]
[*07/26/2021 06:19:33.2596] boot 2 build T-5a1977b5600aa94dd31adcabae872ed6700b2ea1-g5a1977b5-vipendya board corsica mac A0:F8:49:E4:20:10
[*07/26/2021 06:19:33.2596] Module: mbedtls .text=0xbf000000 data=0xbf007e18 bss=0xbf008070
[*07/26/2021 06:19:33.2596] Module: aptrace .text=0xbf00c000 data=0xbf0141dc bss=0xbf0145e0
[*07/26/2021 06:19:33.2596] Module: qca_nss_gmac .text=0xbf01b000 data=0xbf021b7c bss=0xbf02203c
[*07/26/2021 06:19:33.2596] Module: qca_nss_drv .text=0xbf02b000 data=0xbf042a40 bss=0xbf0437f0
[*07/26/2021 06:19:33.2596] Module: qca_nss_capwapmgr .text=0xbf05f000 data=0xbf062b78 bss=0xbf062cc8
[*07/26/2021 06:19:33.2596] Module: nssmgrctl .text=0xbf068000 data=0xbf069728 bss=0xbf069a4c
[*07/26/2021 06:19:33.2596] Module: proclikefs .text=0xbf06f000 data= bss=0xbf06fb40
[*07/26/2021 06:19:33.2596] Module: stile_lm_ft .text= data= bss=
[*07/26/2021 06:19:33.2596] Module: stile_lm_dp .text= data= bss=
[*07/26/2021 06:19:33.2596] Module: bonding .text=0xbf976000 data=0xbf98763c bss=0xbf987a68
[*07/26/2021 06:19:33.2596] Module: ipv6 .text=0xbf994000 data=0xbf9c4840 bss=0xbf9c60ec
[*07/26/2021 06:19:33.2596] Module: lowmemorykiller .text=0xbf9df000 data=0xbf9df2c0 bss=0xbf9df44c
[*07/26/2021 06:19:33.2596] Module: qca_nss_profile_drv .text=0xbf9e3000 data=0xbf9e4324 bss=0xbf9e4498
[*07/26/2021 06:19:33.2596] Module: ssdk_reg .text=0xbf9e9000 data= bss=0xbf9e9838
[*07/26/2021 06:19:33.6595] Last reload reason : 0: unknown
[*07/26/2021 06:19:35.2990]
[*07/26/2021 06:19:35.2990] __ol_ath_attach() Allocated scn c4080480
[*07/26/2021 06:19:35.3090] Chip id: 0x9, chip version: 0x1000000
[*07/26/2021 06:19:35.3090]
[*07/26/2021 06:19:35.3090] Target Version is 1000000
[*07/26/2021 06:19:35.3090]
[*07/26/2021 06:19:35.3090] Flash Download Address c0000
[*07/26/2021 06:19:35.3090] ol_transfer_bin_file: flash data file defined
[*07/26/2021 06:19:35.3090] Cal location [0]: 00000000
[*07/26/2021 06:19:35.3090]
[*07/26/2021 06:19:35.3090] Wifi0 NAND FLASH Select OFFSET 0x1000
[*07/26/2021 06:19:35.3290] qc98xx_verify_checksum: flash checksum passed: 0x395b
[*07/26/2021 06:19:35.3290] ol_transfer_bin_file 4092: Download Flash data len 12064
[*07/26/2021 06:19:35.3490]
[*07/26/2021 06:19:35.3490] Board data initialized
[*07/26/2021 06:19:35.3989] ol_ath_download_firmware :First OTP download and Execute is good address:0xa000 return param 4660
[*07/26/2021 06:19:35.3989] ol_ath_download_firmware:##Board Id 8 , CHIP Id 1
[*07/26/2021 06:19:35.3989] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS260_negative_pwr_offset_2G_v2_008.bin
[*07/26/2021 06:19:35.4789]
[*07/26/2021 06:19:35.4789] [Flash] : Ignore Module param
[*07/26/2021 06:19:35.4789] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[*07/26/2021 06:19:35.4989] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin
[*07/26/2021 06:19:36.5986] HTC Rx: insufficient length, got:4 expected =8
[*07/26/2021 06:19:36.5986] Startup Mode-0 set
[*07/26/2021 06:19:36.5986] HTC Service:0x0300 ep:1 TX flow control disabled
[*07/26/2021 06:19:36.5986] HTC Service:0x0100 ep:2 TX flow control disabled
[*07/26/2021 06:19:36.6086] Firmware_Build_Number:5
[*07/26/2021 06:19:36.6086] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339a79b2 vht_supp_mcs:0x0000ffea
[*07/26/2021 06:19:36.6086]
[*07/26/2021 06:19:36.6086] RES CFG Support wmi_service_bitmap 9778
[*07/26/2021 06:19:36.6086]
[*07/26/2021 06:19:36.6086] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 10 to TGT
[*07/26/2021 06:19:36.6086] Mesh Supported
[*07/26/2021 06:19:36.6785] wmi_ready_event_rx: WMI UNIFIED READY event
[*07/26/2021 06:19:36.6885] ACS not enabled
[*07/26/2021 06:19:36.6885] ol_ath_thermal_mitigation_attach: --
[*07/26/2021 06:19:36.6985] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
[*07/26/2021 06:19:37.7182] FWLOG: [34136] WAL_DBGID_AST_DEL_WDS_ENTRY ( 0xdeadc0de, 0xea, 0x32 )
[*07/26/2021 06:19:37.7182] FWLOG: [34208] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[*07/26/2021 06:19:37.7182] FWLOG: [34208] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[*07/26/2021 06:19:37.7182] FWLOG: [34208] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[*07/26/2021 06:19:37.7182] FWLOG: [34208] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[*07/26/2021 06:19:39.7876] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg40000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000
[*07/26/2021 06:19:39.8675] pid 1626's current affinity mask: 3
[*07/26/2021 06:19:39.8675] pid 1626's new affinity mask: 1
[*07/26/2021 06:19:42.4568] wired0: 1000 Mbps Full Duplex
[*07/26/2021 06:19:42.4568]
[*07/26/2021 06:19:42.5867]
[*07/26/2021 06:19:42.5867] Click sched monitor: schedulers = 1
[*07/26/2021 06:19:44.2862]
[*07/26/2021 06:19:44.2862] phy_value=0: org="0x1800" phy_reg="0x1000"
[*07/26/2021 06:19:55.9825] Loading sha2...
[*07/26/2021 06:19:55.9825] Dumpping sha1...
[*07/26/2021 06:19:57.6320] Loading MIC cert and key
[*07/26/2021 06:19:57.6420] Dumpping sha2...
[*07/26/2021 06:19:59.3615] Loading MIC cert and key
[*07/26/2021 06:19:59.7214] Generating key, this may take a while...
[*07/26/2021 06:20:01.6108] Public key portion is:
[*07/26/2021 06:20:01.6108] ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCypDtMQaNAM2PMQ9pQ1xt64yzjihYhMRmxBOBytl3qt3Z3ebtabXo8cPQMiVDD5MrN6Blgda1OZgIeQxklmhTNK4Xc/026/KwPObuJ54jitRwF+6NROxQyxIyQPW3ft/7eAmOdeHWtW3Sl6HxIOQ0YD1+oIu2/IOOoMUTRxtnfkdTvfm17onKy7uZZZa6x1qYeCHIuLGogAjKDwmPlEgv9yvxBlBzU93TEL9mPBVK52bG07/Xyw/yjqH1hbeUOE/iRqpSvTCdYXb25EQN1nEIMrK/0MdKEtyhbg9h/QCFbQhxrVoVgG/5ET4ZgfB7zA8KL7dbsaH23EV3PREuDwmO1 root@mA0F849E42010
[*07/26/2021 06:20:01.6108] Fingerprint: md5 5c:e8:a6:53:29:71:5e:6c:b0:96:ad:47:47:36:3d:ad
[*07/26/2021 06:20:01.6708] pid 2707's current affinity mask: 3
[*07/26/2021 06:20:01.6708] pid 2707's new affinity mask: 1
[*07/26/2021 06:20:02.1206] gzip -dc /etc/wcp.usermodule.template.gz | sed -e 's/__TX_POWER_2G_FILE__/\/radio_fw\/R2.csv/g' -e 's/__TX_POWER_5G_FILE__/\/radio_fw\/R5.csv/g' -e 's/__EVM_POWER_2G_FILE__/\/radio_fw\/EVM_2.csv/g' -e 's/__EVM_POWER_5G_FILE__/\/radio_fw\/EVM_5.csv/g' -e 's/__DOMAIN_2G__/1/g' -e 's/__DOMAIN_5G__/22/g' -e 's/__PRODUCT_ID__/AIR-AP1852E-C-K9/g' -e 's/__AP_TYPE__/47/g' -e 's/__WIRELESS_MAC__/A0:F8:49:E4:D9:60/g' -e 's/__WIRED_MAC__/A0:F8:49:E4:20:10/g' -e 's/__WIRED1_MAC__/A0:F8:49:E4:20:10/g' | DMALLOC_OPTIONS=debug=0x03,inter=1000,log=/tmp/wcp.dmalloc.log,limit=40000000 wcpd &
[*07/26/2021 06:20:02.5905] Password for 'Cisco' changed
[*07/26/2021 06:20:03.6302] DOT11_DRV[0]: Init Radio0
[*07/26/2021 06:20:03.6502] DOT11_DRV[0]: Stop Radio0
[*07/26/2021 06:20:03.6502] DOT11_DRV[0]: set_channel Channel set to 6
[*07/26/2021 06:20:03.6601] DOT11_DRV[1]: Init Radio1
[*07/26/2021 06:20:03.6601] DOT11_DRV[1]: wifi1: Failed to get radio priv parameter (op 4234)
[*07/26/2021 06:20:03.6801] wifi1 no private ioctls.
[*07/26/2021 06:20:03.6801]
[*07/26/2021 06:20:03.6901] wifi1 no private ioctls.
[*07/26/2021 06:20:03.6901]
[*07/26/2021 06:20:03.6901] wifi1 no private ioctls.
[*07/26/2021 06:20:03.6901]
[*07/26/2021 06:20:03.7001] DOT11_DRV[1]: wifi1: Failed to set parameter (op 4283 arg 1)
[*07/26/2021 06:20:03.7001] DOT11_DRV[1]: wifi1 acfg cmd 2 failed for wifi1 errno 19(No such device)
[*07/26/2021 06:20:03.7001] DOT11_DRV[1]: acfg_set_radio_param param 0x200d value 1 failed
[*07/26/2021 06:20:03.7101] DOT11_DRV[1]: wifi1 acfg cmd 2 failed for wifi1 errno 19(No such device)
[*07/26/2021 06:20:03.7101] DOT11_DRV[1]: acfg_set_radio_param param 0x2017 value 1 failed
[*07/26/2021 06:20:03.7101] DOT11_DRV[1]: wifi1 acfg cmd 19 failed for wifi1 errno 19(No such device)
[*07/26/2021 06:20:03.7101] DOT11_DRV[1]: Radio 1 NF_Calibration request failed !
[*07/26/2021 06:20:03.7101] DOT11_DRV[1]: wifi1: Failed to set parameter (op 4176 arg 1)
[*07/26/2021 06:20:03.7201] DOT11_DRV[1]: wifi1: Failed to set parameter (op 4235 arg 1)
[*07/26/2021 06:20:03.7201] DOT11_DRV[1]: wifi1 acfg cmd 16 failed for wifi1 errno 19(No such device)
[*07/26/2021 06:20:03.7201] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v0 error No such device
[*07/26/2021 06:20:03.7201] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:6F
[*07/26/2021 06:20:03.7301] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v1 error No such device
[*07/26/2021 06:20:03.7301] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:6E
[*07/26/2021 06:20:03.7301] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v2 error No such device
[*07/26/2021 06:20:03.7301] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:6D
[*07/26/2021 06:20:03.7401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v3 error No such device
[*07/26/2021 06:20:03.7401] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:6C
[*07/26/2021 06:20:03.7401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v4 error No such device
[*07/26/2021 06:20:03.7401] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:6B
[*07/26/2021 06:20:03.7401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v5 error No such device
[*07/26/2021 06:20:03.7401] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:6A
[*07/26/2021 06:20:03.7501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v6 error No such device
[*07/26/2021 06:20:03.7501] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:69
[*07/26/2021 06:20:03.7501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v7 error No such device
[*07/26/2021 06:20:03.7501] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:68
[*07/26/2021 06:20:03.7501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v8 error No such device
[*07/26/2021 06:20:03.7501] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:67
[*07/26/2021 06:20:03.7601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v9 error No such device
[*07/26/2021 06:20:03.7601] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:66
[*07/26/2021 06:20:03.7601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v10 error No such device
[*07/26/2021 06:20:03.7601] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:65
[*07/26/2021 06:20:03.7701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v11 error No such device
[*07/26/2021 06:20:03.7701] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:64
[*07/26/2021 06:20:03.7701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v12 error No such device
[*07/26/2021 06:20:03.7701] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:63
[*07/26/2021 06:20:03.7701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v13 error No such device
[*07/26/2021 06:20:03.7701] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:62
[*07/26/2021 06:20:03.7801] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v14 error No such device
[*07/26/2021 06:20:03.7801] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:61
[*07/26/2021 06:20:03.7801] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v15 error No such device
[*07/26/2021 06:20:03.7801] DOT11_DRV[1]: ERROR: Radio BSSID Addr: 00:00:00:00:00:00 does not match with driver BSSID Addr: A0:F8:49:E4:D9:60
[*07/26/2021 06:20:03.7801] DOT11_DRV[1]: Stop Radio1
[*07/26/2021 06:20:03.7901] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_stop_radio ioctl SIOCGIFFLAGS failed for wifi1 error -1
[*07/26/2021 06:20:03.7901] DOT11_DRV[1]: Failure to Stop radio during Base Driver Initialization
[*07/26/2021 06:20:03.7901] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v0 error No such device
[*07/26/2021 06:20:03.7901] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v1 error No such device
[*07/26/2021 06:20:03.8001] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v2 error No such device
[*07/26/2021 06:20:03.8001] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v3 error No such device
[*07/26/2021 06:20:03.8001] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v4 error No such device
[*07/26/2021 06:20:03.8101] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v5 error No such device
[*07/26/2021 06:20:03.8101] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v6 error No such device
[*07/26/2021 06:20:03.8101] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v7 error No such device
[*07/26/2021 06:20:03.8201] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v8 error No such device
[*07/26/2021 06:20:03.8201] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v9 error No such device
[*07/26/2021 06:20:03.8201] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v10 error No such device
[*07/26/2021 06:20:03.8301] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v11 error No such device
[*07/26/2021 06:20:03.8301] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v12 error No such device
[*07/26/2021 06:20:03.8301] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v13 error No such device
[*07/26/2021 06:20:03.8401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v14 error No such device
[*07/26/2021 06:20:03.8401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v15 error No such device
[*07/26/2021 06:20:03.8401] DOT11_DRV[1]: mon1 ioctl op=0x8bf2 len=4 failed: 19 (No such device)
[*07/26/2021 06:20:03.8401] DOT11_DRV[1]: set mode_str 11A to mon1 failed
[*07/26/2021 06:20:03.8501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v0 error No such device
[*07/26/2021 06:20:03.8501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v1 error No such device
[*07/26/2021 06:20:03.8501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v2 error No such device
[*07/26/2021 06:20:03.8601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v3 error No such device
[*07/26/2021 06:20:03.8601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v4 error No such device
[*07/26/2021 06:20:03.8601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v5 error No such device
[*07/26/2021 06:20:03.8701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v6 error No such device
[*07/26/2021 06:20:03.8701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v7 error No such device
[*07/26/2021 06:20:03.8701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v8 error No such device
[*07/26/2021 06:20:03.8801] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v9 error No such device
[*07/26/2021 06:20:03.8801] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v10 error No such device
[*07/26/2021 06:20:03.8901] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v11 error No such device
[*07/26/2021 06:20:03.8901] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v12 error No such device
[*07/26/2021 06:20:03.8901] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v13 error No such device
[*07/26/2021 06:20:03.9001] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v14 error No such device
[*07/26/2021 06:20:03.9001] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver is_vap_present ioctl SIOCGIFFLAGS failed for apr1v15 error No such device
[*07/26/2021 06:20:03.9001] DOT11_DRV[1]: mon1 acfg cmd 30 failed for mon1 errno 19(No such device)
[*07/26/2021 06:20:03.9001] DOT11_DRV[1]: set_channel Channel set to 149
[*07/26/2021 06:20:03.9101] DOT11_DRV[1]: wifi1 acfg cmd 17 failed for wifi1 errno 19(No such device)
[*07/26/2021 06:20:03.9101] DOT11_DRV[1]: wifi1: Failed to set parameter (op 4242 arg 0)
[*07/26/2021 06:20:03.9101] DOT11_DRV[1]: wifi1: Failed to set parameter (op 4241 arg 0)
[*07/26/2021 06:20:03.9201] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v0 error No such device
[*07/26/2021 06:20:03.9201] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v1 error No such device
[*07/26/2021 06:20:03.9201] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v2 error No such device
[*07/26/2021 06:20:03.9301] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v3 error No such device
[*07/26/2021 06:20:03.9301] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v4 error No such device
[*07/26/2021 06:20:03.9401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v5 error No such device
[*07/26/2021 06:20:03.9401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v6 error No such device
[*07/26/2021 06:20:03.9401] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v7 error No such device
[*07/26/2021 06:20:03.9501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v8 error No such device
[*07/26/2021 06:20:03.9501] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v9 error No such device
[*07/26/2021 06:20:03.9601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v10 error No such device
[*07/26/2021 06:20:03.9601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v11 error No such device
[*07/26/2021 06:20:03.9601] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v12 error No such device
[*07/26/2021 06:20:03.9701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v13 error No such device
[*07/26/2021 06:20:03.9701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v14 error No such device
[*07/26/2021 06:20:03.9701] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver vendor_get_bssid ioctl SIOCGIFHWADDR failed for apr1v15 error No such device
[*07/26/2021 06:20:03.9800] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver get_vap_if_index ioctl SIOCGIFINDEX failed for apr1v0 error No such device
[*07/26/2021 06:20:03.9800] wcpd: /san/BUILD/workspace/83MR4_Repost_Cheetah_CCO/label/corsica/base/../elts-meraki/elements/wcp/wcp_db.cc: 1366: void WcpDb::populate_if_index_table(): Assertion `if_index >= 0 && if_index < 64' failed.
[*07/26/2021 06:20:10.3781] ethernet_port wired0, ip 10.15.12.157, netmask 255.255.255.0, gw 10.15.12.1, mtu 1500, bcast 10.15.12.255, dns1 10.11.12.5, dns2 10.11.12.6, domain fccollege.edu.pk
Username:
[*07/26/2021 06:20:37.5296] !!!!! {watchdogd} Process wcpd gone for 60s
[*07/26/2021 06:20:37.5296]
[*07/26/2021 06:20:37.5296] !!!!! {watchdogd} Process capwapd no heartbeat for 60s
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] waiting for WCP to initialize
[*07/26/2021 06:21:02.6717] Socket Invalid Element wcp/wcp_db Handler has_rlan Data 0 Length 10
[*07/26/2021 06:21:02.7117] AP IPv4 Address updated from 0.0.0.0 to 10.15.12.157
[*07/26/2021 06:21:02.7317] dtls_init: Use MIC device cert
[*07/26/2021 06:21:02.7317] dtls_init: Use MIC device cert private key
[*07/26/2021 06:21:02.7317]
[*07/26/2021 06:21:02.7317] CAPWAP State: Init
[*07/26/2021 06:21:02.7317]
[*07/26/2021 06:21:02.7317] Config not found, PNP is required, Starting PNP
[*07/26/2021 06:21:02.7317]
[*07/26/2021 06:21:25.5346] PNP Discovery Timer Expired, Starting CAPWAP Discovery
[*07/26/2021 06:21:25.5346]
[*07/26/2021 06:21:25.5346] CAPWAP State: Discovery
[*07/26/2021 06:21:25.5446] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*07/26/2021 06:21:25.5446]
[*07/26/2021 06:21:25.5446] CAPWAP State: Discovery
[*07/26/2021 06:21:35.0516]
[*07/26/2021 06:21:35.0516] CAPWAP State: Discovery
[*07/26/2021 06:21:35.0616] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*07/26/2021 06:21:42.5792]
[*07/26/2021 06:21:42.5792] !!!!! {watchdogd} Process wcpd gone for 120s
[*07/26/2021 06:21:44.5486]
[*07/26/2021 06:21:44.5486] CAPWAP State: Discovery
[*07/26/2021 06:21:44.5586] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*07/26/2021 06:21:54.0557]
[*07/26/2021 06:21:54.0557] CAPWAP State: Discovery
[*07/26/2021 06:21:54.0656] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*07/26/2021 06:22:03.5627]
[*07/26/2021 06:22:03.5627] CAPWAP State: Discovery
[*07/26/2021 06:22:03.5727] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)

Could you please confirm is it related to software bug problem or device hardware issue?

Thanks

Rich R · ‎08-04-2021

- CAPWAP AP must be configured by WLC you cannot configure it manually by CLI

- I already explained why the AP can't join the WLC but feel free to get your own packet captures to see whether it's the same problem I expect it is.

- Rather than wasting time trying to make a faulty AP work, replace it.

------------------------------
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390

View solution in original post

Leo Laohoo · ‎07-28-2021

Nowhere in the output shows the AP "knows" the WLC details.

What happens if someone enters the following command in: capwap ap primary-base <WLC NAME> <WLC IP ADDRESS>

Tayyab831 · ‎07-28-2021

Dear Mr. Leo thank you, below is given output after entered the command,

[*07/27/2021 05:03:45.6305] CAPWAP State: Discovery
[*07/27/2021 05:03:45.6305] Discovery Request sent to 172.30.61.253, discovery type STATIC_CONFIG(1)
[*07/27/2021 05:03:45.6405] Discovery Request sent to 172.30.61.253, discovery type STATIC_CONFIG(1)
[*07/27/2021 05:03:45.6405] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*07/27/2021 05:03:45.6405] Discovery Response from 172.30.61.253
[*07/27/2021 05:03:45.6405]
[*07/27/2021 05:03:45.6405] This AP model is supported by controller version newer than 7.0.0.0!
[*07/27/2021 05:03:45.6405]
[*07/27/2021 05:03:45.6405] Discovery response from MWAR ''running version 0.0.0.0 is rejected.
[*07/27/2021 05:03:45.6405] Failed to decode discovery response.
[*07/27/2021 05:03:45.6405] CAPWAP SM handler: Failed to process message type 2 state 2.
[*07/27/2021 05:03:45.6405] Failed to handle capwap control message from controller - status 4
[*07/27/2021 05:03:45.6405] Failed to process unencrypted capwap packet 0xf11000 from 172.30.61.253
[*07/27/2021 05:03:45.6405] Failed to send capwap message 0 to the state machine. Packet already freed.
[*07/27/2021 05:03:45.6405] IPv4 wtpProcessPacketFromSocket returned 4
[*07/27/2021 05:03:45.6405] Discovery Response from 172.30.61.253

Leo Laohoo · ‎07-28-2021

@Tayyab831 wrote:

[*07/27/2021 05:03:45.6405] This AP model is supported by controller version newer than 7.0.0.0!

WTF!

Post the complete output to the following WLC command: sh sysinfo

Tayyab831 · ‎07-28-2021

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.3.143.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
OUI File Update Time............................. Sun Sep 07 10:44:07 IST 2014

Build Type....................................... DATA + WPS

System Name...................................... FCC-WLC-5508
System Location.................................. N-Block-Core
System Contact................................... IT Services
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 172.30.61.253
IPv6 Address..................................... ::
Last Reset....................................... Software reset
System Up Time................................... 185 days 16 hrs 58 mins 33 secs
System Timezone Location......................... (GMT +5:00) Karachi, Islamabad, Tashkent
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

Configured Country............................... Multiple Countries : CH,CN,DE,ES,FR,GB,IE,IT,NL,PT,

............................................... SE,US
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +20 C
Fan Status....................................... OK

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 7
Number of Active Clients......................... 743

OUI Classification Failure Count................. 0

Burned-in MAC Address............................ 04:62:73:7A:E5:E0
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 500
System Nas-Id....................................
WLC MIC Certificate Types........................ SHA1/SHA2

Leo Laohoo · ‎07-28-2021

@Tayyab831 wrote:

Configured Country............................... Multiple Countries : CH,CN,DE,ES,FR,GB,IE,IT,NL,PT,SE,US

I am not helping anyone break any laws

Tayyab831 · ‎07-28-2021

Yes, we have about 130 APs of different regulatory domains. This AP was working for long time. About five to seven APs of same model are working currently in our network. Do you think is it related to regulatory domain problem?

Leo Laohoo · ‎07-28-2021

Post the complete output to the AP command: sh version

Tayyab831 · ‎07-28-2021

APA0F8.49E4.2010#sh ver

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

Cisco AP Software, (ap1g4), [wnbu-vmw-lnx-02:/san/BUILD/workspace/83MR4_Repost_Cheetah_CCO/label/corsica]
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon Jun 4 23:03:21 PDT 2018

ROM: Bootstrap program is U-Boot boot loader
BOOTLDR: U-Boot boot loader Version 31

APA0F8.49E4.2010 uptime is 0 days, 0 hours, 1 minutes
Last reload time : Tue Jul 27 05:52:38 UTC 2021
Last reload reason : unknown

cisco AIR-AP1852E-C-K9 ARMv7 Processor rev 0 (v7l) with 967420/800996K bytes of memory.
Processor board ID KWC213303Q4
AP Running Image : 8.3.143.0
Primary Boot Image : 8.3.143.0
Backup Boot Image : 8.2.151.0
2 Gigabit Ethernet interfaces
1 802.11 Radios
Radio FW version : c5d79906494f60ee03674c0779e5c30b
NSS FW version : NSS.AK.1.0.c10-00017-E_custC-1.67978.1

Base ethernet MAC Address : A0:F8:49:E4:20:10
Part Number : 0-0000-00
PCA Assembly Number : 074-13150-02
PCA Revision Number : 01
PCB Serial Number : KWC213303Q4
Top Assembly Part Number : 074-13150-02
Top Assembly Serial Number : KWC213303Q4
Top Revision Number : A0
Product/Model Number : AIR-AP1852E-C-K9

Leo Laohoo · ‎07-28-2021

@Tayyab831 wrote:

Product/Model Number : AIR-AP1852E-C-K9

I am not helping anyone break any laws

Tayyab831 · ‎07-28-2021

Yes, All are in PAK.

Leo Laohoo · ‎07-28-2021

@Tayyab831 wrote:

Yes, All are in PAK.

Let me rephrase my question: Are all the APs with various Regulatory Domains all installed in Pakistan?

Tayyab831 · ‎07-28-2021

Yes, actually we have many refurbish APs of different models and that belong to different regulatory domain.

Leo Laohoo · ‎07-28-2021

@Tayyab831 wrote:
Yes, actually we have many refurbish APs of different models and that belong to different regulatory domain.

I am not helping anyone break any laws, no matter how trivial or insignificant they are.

You, sir, are on your own.

Tayyab831 · ‎07-29-2021

Thank you for your reply. We purchased these 1852 APs brand new about 5 to 6 years ago and regulatory domain was unfortunately not considered as important as you mentioned may be due to some reasons. I was not part of buying process. In future we will make sure to buy the device with the correct regulatory domain. Anyways thank you very much for your support.