Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi there,I am new to networking and wanted to try something out. Maybe someone can help me.I have a Cisco Catalyst 9800 Wlan Controller which is connected to a Switch with 2 Links. One 10Gbit Link and a 1Gbit Link. I want the 10Gbit link to be the li...
I am having trouble trying to find a CLI command that will let me config a WLAN/SSID into 5Ghz only: Radio Policy : 802.11a onlyI've tried the GUI disableing the 2.4, but I'm still getting: Operational State of Radio...
Does the 9300 EWC (embedded wireless controller on Catalyst 9300 switch) support gNMI as model-driven configuration management? Found this documentation, but it does not mention embedded wireless controller on switches.https://www.cisco.com/c/en/us/p...
I upgraded 1 WLC 2504 from 7.3.101.0 to 8.0.152.0. After upgrade the APs will not register. There are 4 3602i's. The WLC is licensed for 5.The AP LED cycles through the boot process and then immediately goes solid green.
Hi Guys!I've looked at some example configurations and community posts. I have the following topology:Foreign WLC [9800] <---> Anchor WLC [5520] <--> DMZ interface (Dynamic interface group with multiple VLANs)We want to use the Anchor WLC DMZ that ha...
Hello,unfortunately, I am not getting anywhere with my problem right now. I have a Cisco 2960-C switch and a Cisco 2702 AP. On the switch I have on Gig1 (WAN1) and on Gig2 (WAN2). Now I want to make a vlan for WAN1 and a vlan for Wan 2. In this case ...
We're considering getting rid of a rather expensive and inflexible third-party solution that currently provides guest wireless access through individual credentials via SMS. The stock Sponsored guest feature, even if bare-bones, seems to be more than...
HiI'm seeking a bit of help on understanding our RF spectrum graph.We had a report of some client issues - packets being dropped on ping to 8.8.8.8.The AP is operating on ch 161, it is a MR57Taking a look at the RF spectrum graph ch 161 did not look ...
Hi, do i need to order a AIR-DNA-E-3/5Y DNA lic with the C9115AXI-I to run them in Controller mode. As i dont know wich controller is in use. Can i order them as opt out and how about running them with out DNA Lic, or do i need to order a adder Lic...
Hello, I have 3 WLC, and have problems to register APs with MIC SHA2 only in WLC1. The difference with the others is in "show sysinfo"... (Cisco Controller) >show sysinfo Manufacturer's Name.............................. Cisco Systems Inc.Product Nam...
Dear Wireless Experts,I had tried to make the factory reset a AP (AIR-CAP3602I-N-K9) and I pressed over the time on MODE button.Now, I boot the AP every time and the console is only showed as Ranma. Any idea to reset it back to normally?
Hi Guys! We have an installation where the following commands were not issued at the beginning of the configuration:1. key config-key password-encrypt (key)2. password encryption aes Consequently, except for user passwords, all passwords/secret/keys ...
I have a pair of 5508 controllers. We are in the process of upgrading to a vWLC 9800. Each of our sites is configured the same. We 2 circuits to each of our sites and managed via SDWAN. One of the circuits is an MPLS circuit back to our HQ and the ot...
Hi,I have a Windows 10 computer that till show a splash page while i connect to our SSID. All other computer connecting to the same SSID does not have this. If I try to connect to another SSID on the same AP there is no problem.
I have WLC 2504 which has one 1142 and one 2702 AP connected in local mode. I have one SSID available on both 2.4 & 5 GHz. My issue is connection speed is stuck at 114Mbps on 5Ghz. I am using Windows 10 Lenovo laptop for testing with Intel(R) Wireles...
