C9130AXI_E stuck downloading image

[HVO-cisco]

WLC 9800-40
Software 17.9.2
Hello, we have a problem with ap's not joing the controller.
Tried a factory reset, and we log the following:

Any suggestions ?

[*02/10/2023 11:04:27.9330] Reset chip in progess, not resetting
[*02/10/2023 11:04:28.0865] DOT11_TXP[1]:Domain configured: 12 class:E
[*02/10/2023 11:04:29.4183] DOT11_DRV[2]: Init Radio2
[*02/10/2023 11:04:29.4493] DOT11_DRV[1]: Init Radio1
[*02/10/2023 11:04:29.4771] DOT11_DRV[1]: Stop Radio1 - Begin
[*02/10/2023 11:04:29.4803] DOT11_DRV[1]: Stop Radio1 - End
[*02/10/2023 11:04:29.4971] wlan: [5582:I:ANY] acfg_set_chan: 988: VAP is not ready. Saving channel [36] to configure later
[*02/10/2023 11:04:29.4972] DOT11_DRV[1]: set_channel Channel set to 36
[*02/10/2023 11:04:29.5051] DOT11_DRV[0]: Init Radio0
[*02/10/2023 11:04:29.7012] wlan: [5582:I:ANY] acfg_set_chan: 988: VAP is not ready. Saving channel [6] to configure later
[*02/10/2023 11:04:29.7016] DOT11_DRV[0]: set_channel Channel set to 6
[*02/10/2023 11:04:29.7283] wlan: [5582:I:ANY] acfg_set_chan: 988: VAP is not ready. Saving channel [1] to configure later
[*02/10/2023 11:04:29.7288] DOT11_DRV[0]: set_channel Channel set to 1
[*02/10/2023 11:04:29.7313] wlan: [5582:I:ANY] acfg_set_chan: 988: VAP is not ready. Saving channel [1] to configure later
[*02/10/2023 11:04:29.7317] DOT11_DRV[0]: set_channel Channel set to 1
[*02/10/2023 11:04:29.7345] DOT11_DRV[0]: Channel set to 1, width 20
[*02/10/2023 11:04:29.7372] wlan: [0:I:ANY] ol_ath_twt_disable_complete_event_handler: 14954: twt disabled.
[*02/10/2023 11:04:29.7372]
[*02/10/2023 11:04:29.7425] DOT11_DRV[0]: Channel set to 1, width 20
[*02/10/2023 11:04:29.7515] wlan: [5582:I:ANY] acfg_set_chan: 988: VAP is not ready. Saving channel [36] to configure later
[*02/10/2023 11:04:29.7520] DOT11_DRV[1]: set_channel Channel set to 36
[*02/10/2023 11:04:29.7600] wlan: [5582:I:ANY] acfg_set_chan: 988: VAP is not ready. Saving channel [36] to configure later
[*02/10/2023 11:04:29.7604] DOT11_DRV[1]: set_channel Channel set to 36
[*02/10/2023 11:04:29.7633] DOT11_DRV[1]: Channel set to 36, width 20
[*02/10/2023 11:04:29.7647] wlan: [0:I:ANY] ol_ath_twt_disable_complete_event_handler: 14954: twt disabled.
[*02/10/2023 11:04:29.7647]
[*02/10/2023 11:04:29.7691] DOT11_DRV[1]: Channel set to 36, width 20
[*02/10/2023 11:04:31.0377] AP is in good condition, BLE is off
[*02/10/2023 11:04:31.0377] Set radio wifi0 power 4 antenna chain 4 15
[*02/10/2023 11:04:31.0377] Set radio wifi1 power 4 antenna chain 8 255
[*02/10/2023 11:04:32.2903] IOT Bootloader Flash Tool 1.4
[*02/10/2023 11:04:32.2904] Firmware upgrade initiated by ble_management
[*02/10/2023 11:04:32.2904] Opening serial console to.. /dev/ttyMSM1
[*02/10/2023 11:04:32.2904] bundled_fw_ver = ['Lodestar', '2.7.16']
[*02/10/2023 11:04:32.2904] RSP: 04FF10FF070002150AFF020710320000000000
[*02/10/2023 11:04:32.2904] ls_ver = 2.7.16
[*02/10/2023 11:04:32.2904] ls_fw_ver 2.7.16
[*02/10/2023 11:04:32.2904] upgrade false
[*02/10/2023 11:04:32.2904] FW version is latest. No need to upgrade
[*02/10/2023 11:04:33.9916] ethernet_port wired0, ip 192.168.251.77, netmask 255.255.255.0, gw 192.168.251.1, mtu 1500, bcast 192.168.251.255, dns1 X.X.X.X, dns2 XX.XX.XX.16, domain XXX.XX<30>systemd[1]: Starting ntp watcher...
[*02/10/2023 11:04:35.3480] AP IPv4 Address updated from 0.0.0.0 to 192.168.251.77
[*02/10/2023 11:04:46.4362] dtls_init: Use SUDI certificate
[*02/10/2023 11:04:46.4393]
[*02/10/2023 11:04:46.4393] CAPWAP State: Init
[*02/10/2023 11:04:52.0954] Start: RPC thread 2680357776 created.
[*02/10/2023 11:05:43.4148]
[*02/10/2023 11:05:43.4148] CAPWAP State: Discovery
[*02/10/2023 11:05:43.4164] Got WLC address X.X.X.140 from DHCP.
[*02/10/2023 11:05:43.4165] IP DNS query for CISCO-CAPWAP-CONTROLLER.XXX.XX
[*02/10/2023 11:06:03.4412] Discovery Request sent to X.X.X.140, discovery type DHCP(2)
[*02/10/2023 11:06:03.4425] Discovery Response from X.X.X.140
[*02/10/2023 11:06:03.4428] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*02/10/2023 11:06:03.4432]
[*02/10/2023 11:06:03.4432] CAPWAP State: Discovery
[*02/10/2023 11:07:32.0002]
[*02/10/2023 11:07:32.0003] CAPWAP State: DTLS Setup
[*02/10/2023 11:07:32.3662] sudi99_request_check_and_load: Use HARSA SUDI certificate
[*02/10/2023 11:07:32.9994]
[*02/10/2023 11:07:32.9994] CAPWAP State: Join
[*02/10/2023 11:07:33.0082] Sending Join request to X.X.X.140 through port 5272
[*02/10/2023 11:07:33.0287] Join Response from X.X.X.140
[*02/10/2023 11:07:33.0288] AC accepted join request with result code: 0
[*02/10/2023 11:07:33.0295] Received wlcType 0, timer 30
[*02/10/2023 11:07:33.0295] TLV ID 2216 not found
[*02/10/2023 11:07:33.0295] TLV-DEC-ERR-1: No proc for 2216
[*02/10/2023 11:07:33.1196]
[*02/10/2023 11:07:33.1196] CAPWAP State: Image Data
[*02/10/2023 11:07:33.1201] AP image version 8.10.130.0 backup 0.0.0.0, Controller 17.9.2.52
[*02/10/2023 11:07:33.1201] Version does not match.
[*02/10/2023 11:07:33.1452] upgrade.sh: Script called with args:[PRECHECK]
[*02/10/2023 11:07:33.1783] do PRECHECK, part1 is active part
[*02/10/2023 11:07:33.2009] upgrade.sh: /tmp space: OK available 80668, required 40000
[*02/10/2023 11:07:33.2013] wtpImgFileReadRequest: request ap1g6a, local /tmp/part.tar
[*02/10/2023 11:07:33.2026] Image Data Request sent to X.X.X.140, fileName [ap1g6a], slaveStatus 0
[*02/10/2023 11:07:33.2040] Image Data Response from X.X.X.140
[*02/10/2023 11:07:33.2040] AC accepted join request with result code: 0
[*02/10/2023 11:07:33.2082] <.....................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:07:40.1031] ..........Set PnP NTP Server pnpntpserver.XX.no.
[*02/10/2023 11:07:45.1034] ...................
[*02/10/2023 11:07:55.1778] ..................................................
[*02/10/2023 11:08:20.2025] ...............<30>systemd[1]: Starting Pnp Watcher...
[*02/10/2023 11:08:30.0739] Warning: Stopping dbg_day0_bundle.service, but it can still be activated by:
[*02/10/2023 11:08:30.0739] dbg_day0_bundle.timer
[*02/10/2023 11:08:30.3404] ..........<30>systemd[1]: Stopped Pnp agent.
[*02/10/2023 11:08:34.1157] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:08:36.1378] ..............Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:08:48.5273] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:08:48.7317] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:08:52.0475] ...........
[*02/10/2023 11:08:58.0077] ..................................................
[*02/10/2023 11:09:14.7405] ........................Invalid event 56 & state 10 combination.
[*02/10/2023 11:09:26.9926] Failed to handle timer message.
[*02/10/2023 11:09:27.2703] ......Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:09:28.7518] ....................
[*02/10/2023 11:09:37.9582] ..................................................
[*02/10/2023 11:10:00.5021] .............> 84377600 bytes, 62735 msgs, 370 last
[*02/10/2023 11:10:03.0973] Last block stored, IsPre 0, WriteTaskId 0
[*02/10/2023 11:10:03.0974] Image transfer completed from WLC, last 1
[*02/10/2023 11:10:03.0976] wtpProcessImageDataRequest(10): fileName ap1g6a, pre 0
[*02/10/2023 11:10:03.1220] upgrade.sh: Script called with args:[PREDOWNLOAD]
[*02/10/2023 11:10:03.1535] do PREDOWNLOAD, part1 is active part
[*02/10/2023 11:10:03.1685] upgrade.sh: Start doing upgrade arg1=PREDOWNLOAD arg2= arg3= ...
[*02/10/2023 11:10:03.2211] upgrade.sh: Using image /tmp/part.tar on axel-qca ...
[*02/10/2023 11:10:03.2213] sh: write error: No space left on device
[*02/10/2023 11:10:03.2258] tar: write error: No space left on device
[*02/10/2023 11:10:03.2537] upgrade.sh: ERROR: Image type mismatch. Expected:ap1g6a Got:
[*02/10/2023 11:10:03.2700] upgrade.sh: Cleanup for do_upgrade...
[*02/10/2023 11:10:03.2864] upgrade.sh: /tmp/upgrade_in_progress cleaned
[*02/10/2023 11:10:03.3009] upgrade.sh: Cleanup tmp files ...
[*02/10/2023 11:10:03.3414] capwap-upgrade script returned failure when calling PREDOWNLOAD.
[*02/10/2023 11:10:03.3417] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:10:03.3419] CAPWAP SM handler: Failed to process message type 15 state 10.
[*02/10/2023 11:10:03.3419] Failed to handle capwap control message from controller - status 2
[*02/10/2023 11:10:03.3420] Failed to process encrypted capwap packet 0x5560029000 from X.X.X.140
[*02/10/2023 11:10:03.3420] Failed to send capwap message 0 to the state machine. Packet already freed.
[*02/10/2023 11:10:19.4299] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:10:27.0528] Re-Tx Count=1, Max Re-Tx Value=5, SendSeqNum=7, NumofPendingMsgs=1
[*02/10/2023 11:10:27.0528]
[*02/10/2023 11:10:29.9037] Re-Tx Count=2, Max Re-Tx Value=5, SendSeqNum=7, NumofPendingMsgs=1
[*02/10/2023 11:10:29.9037]
[*02/10/2023 11:10:32.7546] Re-Tx Count=3, Max Re-Tx Value=5, SendSeqNum=7, NumofPendingMsgs=1
[*02/10/2023 11:10:32.7546]
[*02/10/2023 11:10:35.6056] Re-Tx Count=4, Max Re-Tx Value=5, SendSeqNum=7, NumofPendingMsgs=1
[*02/10/2023 11:10:35.6056]
[*02/10/2023 11:10:38.4565] Re-Tx Count=5, Max Re-Tx Value=5, SendSeqNum=7, NumofPendingMsgs=1
[*02/10/2023 11:10:38.4565]
[*02/10/2023 11:10:41.3074] Max retransmission count exceeded, going back to DISCOVER mode.
[*02/10/2023 11:10:41.3075] Dropping msg CAPWAP_ECHO_REQUEST, type = 1, len = 0, eleLen = 8, sendSeqNum = 7
[*02/10/2023 11:10:41.3280]
[*02/10/2023 11:10:41.3280] CAPWAP State: DTLS Teardown
[*02/10/2023 11:10:41.3426] Aborting image download(0x0): Dtls cleanup, ap1g6a
[*02/10/2023 11:10:41.4175] upgrade.sh: Script called with args:[ABORT]
[*02/10/2023 11:10:41.4502] do ABORT, part1 is active part
[*02/10/2023 11:10:41.4744] upgrade.sh: Cleanup tmp files ...
[*02/10/2023 11:10:41.4976] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*02/10/2023 11:10:41.4976] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*02/10/2023 11:10:56.0797]
[*02/10/2023 11:10:56.0797] CAPWAP State: Discovery
[*02/10/2023 11:10:56.0804] Got WLC address X.X.X.140 from DHCP.
[*02/10/2023 11:10:56.0805] IP DNS query for CISCO-CAPWAP-CONTROLLER.XXX.XX
[*02/10/2023 11:11:16.1022] Discovery Request sent to X.X.X.140, discovery type DHCP(2)
[*02/10/2023 11:11:16.1037] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*02/10/2023 11:11:16.1038] Discovery Response from X.X.X.140
[*02/10/2023 11:11:16.1045] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Discovery(2).
[*02/10/2023 11:11:25.0003]
[*02/10/2023 11:11:25.0003] CAPWAP State: DTLS Setup
[*02/10/2023 11:11:25.6318]
[*02/10/2023 11:11:25.6318] CAPWAP State: Join
[*02/10/2023 11:11:25.6340] Sending Join request to X.X.X.140 through port 5272
[*02/10/2023 11:11:25.6379] Join Response from X.X.X.140
[*02/10/2023 11:11:25.6379] AC accepted join request with result code: 0
[*02/10/2023 11:11:25.6424] Received wlcType 0, timer 30
[*02/10/2023 11:11:25.6424] TLV ID 2216 not found
[*02/10/2023 11:11:25.6424] TLV-DEC-ERR-1: No proc for 2216
[*02/10/2023 11:11:25.6655]
[*02/10/2023 11:11:25.6655] CAPWAP State: Image Data
[*02/10/2023 11:11:25.6658] AP image version 8.10.130.0 backup 0.0.0.0, Controller 17.9.2.52
[*02/10/2023 11:11:25.6658] Version does not match.
[*02/10/2023 11:11:25.6908] upgrade.sh: Script called with args:[PRECHECK]
[*02/10/2023 11:11:25.7238] do PRECHECK, part1 is active part
[*02/10/2023 11:11:25.7459] upgrade.sh: /tmp space: OK available 80600, required 40000
[*02/10/2023 11:11:25.7463] wtpImgFileReadRequest: request ap1g6a, local /tmp/part.tar
[*02/10/2023 11:11:25.7474] Image Data Request sent to X.X.X.140, fileName [ap1g6a], slaveStatus 0
[*02/10/2023 11:11:25.7488] Image Data Response from X.X.X.140
[*02/10/2023 11:11:25.7488] AC accepted join request with result code: 0
[*02/10/2023 11:11:25.7537] <.......<30>systemd[1]: Starting Lighttpd Watcher...
[*02/10/2023 11:11:31.1014] ...........................................
[*02/10/2023 11:11:40.6688] ......................................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:11:47.8905] .Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:11:48.1390] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:11:53.5490] ...........
[*02/10/2023 11:11:55.8135] ................................................Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*02/10/2023 11:12:09.6671] ..
[*02/10/2023 11:12:10.0406] ........................

[marce1000]

 - Check this thread for hints : https://community.cisco.com/t5/other-network-architecture-subjects/9130axi-can-t-join-9800-80-wlc-write-error-no-space-left-on/m-p/4737454

 M.

[Rich R · Accepted solution]

This was actually covered in the 9800 troubleshooting session at Cisco Live 2 days ago! 
"17.3.5 works as upgrade hop towards 17.9 especially for 9130.  Problem : APs that you kept in stock or got through RMA might not join a 17.9 WLC anymore" 
The new image won't fit in the existing flash partition size so upgrade will never succeed.  You are running very old code on that AP!

The guidance for AP running 17.2 or 17.3.1 to 17.3.4 is to first upgrade the AP to 17.3.5 (or later) or 17.6.x (which will increase the partition size) and then upgrade to 17.9.x
As your AP is running 8.10.130.0 you might even need to upgrade it to 8.10.183.0 before trying the above step.
You can download the upgrade images directly and upgrade via console with TFTP.

[HVO-cisco]

@Rich R 
Thank you very much !!

Regards
Johann Folkestad

[dal]

I have this problem

Any guide on how to upgrade the C9130AXI via TFTP?

Thanks

[Rich R]

AP#archive download-sw /reload ?
WORD URL of AP image <tftp|sftp>://<server_ip>/<file_path>

Just remember you need to upgrade it to an intermediate version first to get the partition sizes adjusted before you upgrade to the latest versions.

This is also covered in the TAC recommended versions page (link below) and the release notes https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-9/release-notes/rn-17-9-9800.html#Cisco_Concept.dita_59a2987f-2633-4630-8c7b-a8e8aecdeaf7 both of which you should always consult before starting upgrades.

[Thomas Lindell]

I mean it's less that obvious

This will work

!if you issue a show version on your ap and it tells you it's AP Running IMage is 8.10.130.0

!ex:

Processor board ID FJC25411PKG
AP Running Image : 8.10.130.0
Primary Boot Image : 8.10.130.0
Backup Boot Image : 0.0.0.0
Primary Boot Image Hash:
Backup Boot Image Hash:

Hold down the Reset button for 30 Seconds during power up while serial console is attached
once at the login prompt login with
Username = Cisco
Password = Cisco
en
Cisco

!Assign a Required IP so you can reach your TFTP Server
!First download the Legacy LWAPP Firmware it's necessary to Extract it from C9800-AP-universalk9.17.03.08a.zip
!in the case of the 9130Axi you need ap1g6a
!put that image on your TFTP Server

archive download-sw /no-reload tftp://192.168.1.1/ap1g6a
reboot
archive download-sw /no-reload tftp://192.168.1.1/ap1g6a-k9w8-tar.153-3.JPS.tar

After this you can connect it to a controller and it will work properly

[Rich R]

Did you mean "it's less than obvious" @Thomas Lindell ?

> !First download the Legacy LWAPP Firmware it's necessary to Extract it from C9800-AP-universalk9.17.03.08a.zip
Or you can just download it directly from
https://software.cisco.com/download/home/286323627/type/286288051/release/15.3.3-JK11

> archive download-sw /no-reload tftp://192.168.1.1/ap1g6a-k9w8-tar.153-3.JPS.tar
The original poster was trying to join the AP to a WLC running 17.9.2 so the correct image for that would be:
https://software.cisco.com/download/home/286323627/type/286288051/release/15.3.3-JPN1
15.3(3)JPS is for 17.14.1.

[JiriCapek8710]

hi,

is anyone able to provide me with ap1g6a-k9w8-tar.153-3.JK11.tar as it is no longer available on the download page....thx!

[Rich R]

The file is still available to download! I already provided the link in my previous reply.  Here it is again:
https://software.cisco.com/download/home/286323627/type/286288051/release/15.3.3-JK11

Note that we are not allowed to share Cisco licensed software.

[JiriCapek8710]

hi Rich, true, it is available, but my request was turned down by support with explanation that I do not have Service contract for the part.... , so i am not entitled to download sw for it.  Which to be honest is not expected.

Br

J

[Rich R]

That's a fact of life - Cisco only provide software updates to customers with the correct support contract in place and that's why we are not allowed to share the software because that would put us in breach of Cisco license conditions and our own contracts.

[Leo Laohoo]

Console into the AP and reboot. 

Post the entire boot-up process.

[JiriCapek8710]

Leo, attached is the boot log. I believe the issue is that 8.10.130.0 is NOT supporting partitioning needed to accommodate latest image (which I can download). So step through old ones is needed but it is not available for me....

U-Boot REL 2016.01 (btldr release 127) (May 04 2020 - 15:49:06 -0700)

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

DRAM: 2 GiB
Nand: Detected ONFI Micron TH58NYG3S0H 8G 1.8V 8-bit
qpic_nand: changing oobsize to 160 from 224 bytes
SF: Detected MX25U6435F with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Scanning shenv data blocks
Total valid parts=4
Active shenv part[0:1], write_counter=62
MFG data loaded
PCI Link Intialized
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010001
SKU: Axel-E BID detected...
i2c_0 chip addresses: 30 48 70
Net: MAC0 addr:70:f0:96:6:56:a8
PHY ID: 0x31c31c22... Found AQR114C B0 PHY.
Loaded 7 5 PHY firmware from flash
CRC check good on phy fw file (0x0FE7)
PHYFW:Loading IRAM...........done.
PHYFW:Loading DRAM..............done.
phy fw image load good CRC-16 matches (0xC47C)
PHY ID1: 0x31c3
PHY ID2: 0x1c22
EDMA ver 1 hw init
eth0
Auto boot mode, use bootipq directly
APPS power cycled and restart reason is 0x10
Hit ESC key to stop autoboot: 0
Specified BOOT: part1
ubi0: attaching mtd2
ubi0: scanning is finished
+-------------------------------+
| part1: 1650 PEBs|
| part2: 2300 PEBs|
+-------------------------------+
ubi0: attached mtd2 (name "mtd=0", size 1024 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 4096, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 14 12699133
ubi0: available PEBs: 62, total reserved PEBs: 4034, PEBs reserved for bad PEB h andling: 80

Booting from part1

Loading file 'part1/part.bin' to addr 0x54000000...
Done
Signature returns 0
Image signing verification success, continue to run...
bootm 0x54000400
## Booting kernel from Legacy Image at 54000400 ...
Image Name: Axel Firmware Image
Created: 2020-07-29 13:47:30 UTC
Image Type: AArch64 Linux Multi-File Image (lzma compressed)
Data Size: 6579591 Bytes = 6.3 MiB
Load Address: 41080000
Entry Point: 41080000
Contents:
Image 0: 3375352 Bytes = 3.2 MiB
Image 1: 3123948 Bytes = 3 MiB
Image 2: 80275 Bytes = 78.4 KiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 54000400 ...
## Flattened Device Tree from multi component Image at 54000400
Booting using the fdt at 0x54633034
Uncompressing Multi-File Image ... OK
Loading Ramdisk to 4a005000, end 4a2ffaec ... OK
Loading Device Tree to 4a3a7000, end 4a3bd992 ... OK
Using machid 0x8010001 from environment

Starting image ...

Jumping to AARCH64 kernel via monitor
[01/01/1970 00:00:00.0000] Booting Linux on physical CPU 0x0
[01/01/1970 00:00:00.0000] Linux version 4.4.60 (aut@wnbu-tools-lnx6) (gcc versi on 5.3.0 (OpenWrt GCC 5.3.0 r48430) ) #1 SMP Wed Jul 29 04:22:22 PDT 2020
[01/01/1970 00:00:00.0000] Boot CPU: AArch64 Processor [410fd034]
[01/01/1970 00:00:00.0000] Ignoring memory range 0x40000000 - 0x41000000
[01/01/1970 00:00:00.0000] Kernel command line: console=ttyMSM0,9600n8 ubi.mtd=7 root=/dev/ram activepart=part1 activeboot=0 boardid=0xe swiotlb=1 crashkernel=1 28M@2816M usbcore.authorized_default=0
[01/01/1970 00:00:00.0000] CPU1: Booted secondary processor [410fd034]
[01/01/1970 00:00:00.0000] CPU2: Booted secondary processor [410fd034]
[01/01/1970 00:00:00.0000] CPU3: Booted secondary processor [410fd034]
[01/01/1970 00:00:00.0000] SMP: Total of 4 processors activated.
[01/01/1970 00:00:02.5499] arch_setup_msi_irqs
[01/01/1970 00:00:02.5499] pcie_create_qgic_msi_irq:pos=0 irq=113, dev->msi[0]=1 13 113
[01/01/1970 00:00:02.5499] TZ Log : Will warn on Access Violation, as paniconacc essviolation is not set
[01/01/1970 00:00:03.5599] buginf tty flushing thread started, ttyport=ffffffc01 f288800
[01/01/1970 00:00:03.5599] diag: IPC Logging disabled
[01/01/1970 00:00:03.7599] m25p80 spi32766.0: found mx25u6435f, expected n25q128 a11
[01/01/1970 00:00:03.8299] Skip QCA8074V1 in V2 platform
[01/01/1970 00:00:04.1799] DEV CI test message
[01/01/1970 00:00:04.2099] cpufreq: cpufreq_online: CPU0: Running at unlisted fr eq: 800000 KHz
[01/01/1970 00:00:04.2099] cpufreq: cpufreq_online: CPU0: Unlisted initial frequ ency changed to: 1017600 KHz
[01/01/1970 00:00:04.3099] DEV CI test message
[*01/01/1970 00:00:07.7651] buginf() enabled.
[*01/01/1970 00:00:07.7709] Made it into bootsh: Jul 29 2020 06:28:39 T-cbfc6f1f 9918f53aa2f774f4ee9f9aefab116a16-gcbfc6f1f-aut
[*01/01/1970 00:00:15.2662] bootsh mini ramfs booted /bootpart/part1/ramfs_data_ cisco.cpio.lzma

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.

This product contains some software licensed under the
"GNU Affero General Public License, version 3" provided
with ABSOLUTELY NO WARRANTY under the terms of
"GNU Affero General Public License, version 3", available here:
http://www.gnu.org/licenses/agpl-3.0.html.

[ OK ] Reached target Timers.
[ OK ] Created slice -.slice.
[ OK ] Created slice system.slice.
Starting Cisco UBIFS reformat/mount...
[*01/01/1970 00:00:38.6941] root: Cisco Axel file system mounting
[ OK ] Reached target Slices.
[ OK ] Reached target Cisco File Systems (Pre).
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Listening on Delayed Shutdown Socket.
[ OK ] Reached target Sockets.
[ OK ] Started Cisco UBIFS reformat/mount.
Starting Cisco early mount...
[ OK ] Started Cisco early mount.
[ OK ] Reached target Local File Systems (Pre).
Starting Cisco fips check...
Starting Cisco seed generation...
[*01/01/1970 00:00:39.8285] GCM-128 POST passed
[*01/01/1970 00:00:39.8286] GCM-256 POST passed
Starting Cisco system time setup...
[*04/30/2021 23:59:59.0092] Last reload time: May 1 05:44:06 2021
[*05/01/2021 05:44:06.0003] Setting system time Sat May 1 05:44:06 UTC 2021
Starting Cisco platform file generation...
[ OK ] Started Cisco fips check.
[ OK ] Started Cisco seed generation.
[ OK ] Started Cisco system time setup.
[ OK ] Started Cisco platform file generation.
[ OK ] Reached target Local File Systems.
Starting Cisco S10 boot service...
Starting Cisco act2 check...
[ OK ] Started Cisco system time saving.
[*05/01/2021 05:44:06.7363] 11
[*05/01/2021 05:44:06.7954] Active version: 8.10.130.0
[*05/01/2021 05:44:06.7974] Backup version: 0.0.0.0
Starting Cisco system time saving...
Starting Security Auditing Service...
[*05/01/2021 05:44:07.0860] parameter passed without an option given
Starting Cisco pkg install service...
[ OK ] Started Security Auditing Service.
[ OK ] Started Cisco S10 boot service.
Starting Cisco nss service...
[*05/01/2021 05:44:08.9728] NSS firmware 1 booted
[*05/01/2021 05:44:08.9765] NSS firmware 0 booted
[*05/01/2021 05:44:09.1914]
[*05/01/2021 05:44:09.1914]
[*05/01/2021 05:44:09.1914]
[*05/01/2021 05:44:09.1914]
[*05/01/2021 05:44:09.1914] Authenticating ACT2 ID:C9130
[*05/01/2021 05:44:09.1914] Authenticating SN:KWC25100QCV
[*05/01/2021 05:44:09.1920]
[*05/01/2021 05:44:09.1920] (ACT2Boot) Hardware is Cisco (c) authentic
[*05/01/2021 05:44:09.1920]
[*05/01/2021 05:44:09.2002] Seeding /dev/urandom from ACT2
[*05/01/2021 05:44:09.3059] Current value of FACTORY_RESET=0
[*04/30/2021 23:59:59.0290] Last reload time: May 1 05:44:06 2021
[*05/01/2021 05:44:06.0004] Setting system time Sat May 1 05:44:06 UTC 2021
[*05/01/2021 05:44:06.0325] Initializing wired0 70:F0:96:06:56:A8 interface
[*05/01/2021 05:44:06.1338] device wired0 entered promiscuous mode
[*05/01/2021 05:44:06.1622] Reading ACT2 SUDI certificates
[*05/01/2021 05:44:06.8579] Last reload reason : 0: unknown
[*05/01/2021 05:44:07.5991]
[*05/01/2021 05:44:07.5991] ACT2 Check passed
[*05/01/2021 05:44:07.5992]
Starting Cisco marlin_sia module service...
Starting Cisco nolan service...
Starting Cisco watchdog...
[ OK ] Started Cisco act2 check.
[ OK ] Started Cisco nss service.
[05/01/2021 05:44:08.4999] qcom wdt: Set timeout to 32 seconds
[ OK ] Started Cisco marlin_sia module service.
[ OK ] Started Cisco nolan service.
[ OK ] Started Cisco watchdog.
[ OK ] Started Cisco pkg install service.
Starting Cisco nolan USB service...
Starting Cisco S15platform...
Starting Cisco Kclick...
[ OK ] Started Cisco nolan USB service.
[ OK ] Started Cisco pre-PoE negotiation.
[05/01/2021 05:44:09.1699] Disabling lock debugging due to kernel taint
[*05/01/2021 05:44:09.1970] stile module dp init successfully
[*05/01/2021 05:44:09.1970] NBAR Label:BLD_POLARIS_DEV_LATEST_20200414_053707 Mo dule timestamp: Jul 29 2020 at 04:55:09 User: tta Starting Cisco pre-PoE negotiation...
[ OK ] Started Cisco S15platform.
[ OK ] Started Cisco Kclick.
Starting Cisco ME service...
Starting Cisco Kclick...
Starting Cisco Sku service...
Starting Cisco certificate create service...
[ OK ] Started Cisco ME service.
[*05/01/2021 05:44:09.9573] Cannot change rx-vlan-offload
[*05/01/2021 05:44:09.9598] Cannot change tx-vlan-offload
[ OK ] Started Cisco Sku service.
[ OK ] Started Cisco Kclick.
[ OK ] Started Cisco certificate create service.
Starting Cisco certtime service...
[ OK ] Started Cisco Tam service.
Starting Cisco Tam service...
Starting Cisco FIPS QCA radio POST...
Starting Cisco S16platfomm...
Starting rsyslog client...
Starting Cisco syslog service...
[ OK ] Started Cisco FIPS QCA radio POST.
[ OK ] Started Cisco S16platfomm.
[ OK ] Started rsyslog client.
[ OK ] Started Cisco syslog service.
Starting Cisco synclogd...
Starting RHL daemon...
[05/01/2021 05:44:11.1899] arch_setup_msi_irqs
[05/01/2021 05:44:11.1899] pcie_create_qgic_msi_irq:pos=1 irq=114, dev->msi[0]=1 13 114
[05/01/2021 05:44:11.2299] pcie_create_qgic_msi_irq:pos=2 irq=115, dev->msi[0]=1 13 115
[05/01/2021 05:44:11.3199] pcie_create_qgic_msi_irq:pos=3 irq=116, dev->msi[0]=1 13 116
[05/01/2021 05:44:11.4099] pcie_create_qgic_msi_irq:pos=4 irq=117, dev->msi[0]=1 13 117
[05/01/2021 05:44:11.4999] pcie_create_qgic_msi_irq:pos=5 irq=118, dev->msi[0]=1 13 118
[05/01/2021 05:44:11.5999] pcie_create_qgic_msi_irq:pos=6 irq=119, dev->msi[0]=1 13 119
[05/01/2021 05:44:11.6899] pcie_create_qgic_msi_irq:pos=7 irq=120, dev->msi[0]=1 13 120
[05/01/2021 05:44:11.7799] pcie_create_qgic_msi_irq:pos=8 irq=121, dev->msi[0]=1 13 121
[ OK ] Started Cisco synclogd.
[05/01/2021 05:44:12.1399] NXP-RHL-Driver 0000:01:00.0: RHL: AP TYPE = 2
[05/01/2021 05:44:12.1599] NXP-RHL-Driver 0000:01:00.0: Final VSPA image size va l 0xf10000
[ OK ] Started RHL daemon.
[ OK ] Started Cisco certtime service.
[ OK ] Reached target System Initialization.
[ OK ] Reached target Paths.
[ OK ] Reached target Basic System.
Starting Cisco rtd service...
Starting Cisco printkd...
Starting OpenSSH server daemon...
[ OK ] Started NSS Firmware Monitor daemon.
Starting NSS Firmware Monitor daemon...
[ OK ] Started System Monitor service.
Starting System Monitor service...
Starting BLE init service...
Starting Fast CGI daemon...
Starting Sensord daemon...
[ OK ] Started NTP_PROC daemon.
Starting NTP_PROC daemon...
Starting Cisco led service...
Starting AP Trace daemon...
[*05/01/2021 05:44:11.9037] rhl_reset : got minor 53
[*05/01/2021 05:44:12.2117] V2H call back init
[*05/01/2021 05:44:12.2117] V2H callback registered
[*05/01/2021 05:44:14.5100] starting tam services using ACT2...
[*05/01/2021 05:44:14.5100]
[*05/01/2021 05:44:14.5100] TAM init done
[*05/01/2021 05:44:16.6916] taskset: invalid number '0xe'
Starting capwapd...
Starting Clean Air daemon...
Starting Cisco brain service...
Starting Cisco kexec...
Starting Hostapd process...
[ OK ] Started RHL monitor/reset daemon.
[*05/01/2021 05:44:17.5195] reset device opened
Starting RHL monitor/reset daemon...
Starting WCPD process...
Starting Cisco klogd...
Starting gRPC server daemon...
[ OK ] Started Serial Getty on ttyS0.
Starting Serial Getty on ttyS0...
[ OK ] Reached target Login Prompts.
[ OK ] Started Cisco led service.
[ OK ] Started Cisco kexec.
[ OK ] Started OpenSSH server daemon.
[ OK ] Started Cisco printkd.
[ OK ] Started Cisco klogd.
[ OK ] Started Fast CGI daemon.
[ OK ] Started Cisco rtd service.
[ OK ] Started AP Trace daemon.
[ OK ] Started Sensord daemon.
[ OK ] Started Hostapd process.
[ OK ] Started Cisco brain service.
[*05/01/2021 05:44:18.8684] pid 3637's current affinity mask: f
[05/01/2021 05:44 :18.9499] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done
[*05/01/2021 05:44:18.8684] pid 3637's new affinity mask: 1
[*05/01/2021 05:44:18.9589] wlan: [3698:I:ANY] =======ol_if_regist[05/01/2021 05 :44:19.3299] glink_xprt_open_event
[05/01/2021 05:44:19.3499] diag: In diag_send_feature_mask_update, control chann el is not open, p: 2, ffffffc0011491a8
[05/01/2021 05:44:19.3499] cnss: BDF download response , result: 0, err: 0x0
[05/01/2021 05:44:19.3599] cnss: BDF download response , result: 0, err: 0x0
[ OK ] Started Cisco Power Daemon.
Starting Cisco Power Daemon...
Starting dnsmasq watcher...
Starting DNSmasq...
[ OK ] Started DNSmasq.
[ OK ] Started dnsmasq watcher.
Starting Lighttpd Watcher...
Starting dnsmasq watcher...
[*05/01/2021 05:44:19.3425] [ol_ath_ahb_ssr]: ### SSR event ## 3
[*05/01/2021 05:44:19.4429] wlan: [3698:I:ANY] pld_ahb_wlan_enable: 689: cnss_mo de: Mission mode
[*05/01/2021 05:44:19.4526] wlan: [3698:I:ANY] __ol_ath_attach: 4032: Booting wi th Dynamic HW Mode feature enabled
[*05/01/2021 05:44:19.4558] wlan: [3698:I:ANY] ol_target_init_complete: 6881: CD P soc attach success
[*05/01/2021 05:44:19.4566] wlan: [6:I:dfs] WLAN_DEBUG_DFS : csc_wlan_dfs_sinfo_ notify_handler_cb: 1138: Cisco DFS module registered.
[*05/01/2021 05:44:19.4570] wlan: [6:I:dfs] WLAN_DEBUG_DFS : csc_wlan_dfs_sinfo_ notify_handler_cb: 1138: Cisco DFS module registered.
[*05/01/2021 05:44:19.6019] wlan: [6:I:ANY] copy_fw_abi_version_tlv: 6666: copy_ fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0
[*05/01/2021 05:44:19.8394] wlan: [6:I:ANY] dp_peer_map_attach_wifi3: 8797: dp_p eer_map_attach_wifi3 max_peers 1327, max_ast_index: 4112
[*05/01/2021 05:44:19.8394]
[*05/01/2021 05:44:19.8400] wlan: [3698:I:ANY] ol_ath_update_wireless_modes: 147 0: Wireless_modes = 397f9001 after update
[*05/01/2021 05:44:19.8402] wlan: [3698:I:ANY] acfg_attach: 4602: acfg_attach: 4 602: Netlink socket created:ffffffc060f34c00
[*05/01/2021 05:44:19.8409] wlan: [3698:I:ANY] ol_ath_configure_cong_ctrl_max_ms dus: 3785: pdev_idx = 0 tx_desc_limit = 0
[*05/01/2021 05:44:19.8410] wlan: [3698:I:ANY] wlan_cfg80211_init: 10964: Number of 5G channels: 25
[*05/01/2021 05:44:19.8414] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_han dler: 14936: twt enabled.
[*05/01/2021 05:44:19.8414]
[*05/01/2021 05:44:19.8421] wlan: [3698:I:ANY] ol_ath_update_wireless_modes: 147 0: Wireless_modes = 680680c after update
[*05/01/2021 05:44:19.8426] wlan: [3698:I:ANY] ol_ath_configure_cong_ctrl_max_ms dus: 3785: pdev_idx = 1 tx_desc_limit = 0
[*05/01/2021 05:44:19.8426] wlan: [3698:I:ANY] wlan_cfg80211_init: 10952: Number of 2G channels: 11
[*05/01/2021 05:44:19.8429] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_han dler: 14936: twt enabled.
[*05/01/2021 05:44:19.8429]
[*05/01/2021 05:44:19.8437] wlan: [3698:I:ANY] ol_ath_update_wireless_modes: 147 0: Wireless_modes = 397f9001 after update
[*05/01/2021 05:44:19.8448] wlan: [3698:I:ANY] ol_ath_configure_cong_ctrl_max_ms dus: 3785: pdev_idx = 2 tx_desc_limit = 0
[*05/01/2021 05:44:19.8449] wlan: [3698:I:ANY] wlan_cfg80211_init: 10964: Number of 5G channels: 25
[*05/01/2021 05:44:19.8453] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_han dler: 14936: twt enabled.
[*05/01/2021 05:44:19.8453]
[*05/01/2021 05:44:19.8465] wlan: [3698:E:QLD] qld_register: 108: Handle or addr ess is NULL
[*05/01/2021 05:44:19.8465] wlan: [3698:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pc i_wifi3.0: (Atheros/multi-bss)
[*05/01/2021 05:44:20.6842] wlan: [4283:I:ANY] dp_lag_pdev_set_sta_vdev: 60: dp_ lag_pdev_set_sta_vdev pdev(ffffffc060631608) sta_vdev ffffffc058876400
[*05/01/2021 05:44:21.0381] wlan: [4688:I:ANY] dp_lag_pdev_set_sta_vdev: 60: dp_ lag_pdev_set_sta_vdev pdev(ffffffc060631008) sta_vdev ffffffc0586a5000
[*05/01/2021 05:44:21.3906] wlan: [5097:I:ANY] dp_lag_pdev_set_sta_vdev: 60: dp_ lag_pdev_set_sta_vdev pdev(ffffffc060631c08) sta_vdev ffffffc063fdc400
[*05/01/2021 05:44:21.5389] EEPROM Size = 65536
[*05/01/2021 05:44:21.5389] loading trx table from EEPROM to DTCM
[*05/01/2021 05:44:21.5389] 24480 bytes copied from RHL EEPROM to DTCM
[*05/01/2021 05:44:21.5389] EEPROM Size = 65536
[*05/01/2021 05:44:21.5389] loading ro1 table from EEPROM to DTCM
[*05/01/2021 05:44:21.5389] 12240 bytes copied from RHL EEPROM to DTCM
[*05/01/2021 05:44:21.5389] EEPROM Size = 65536
[*05/01/2021 05:44:21.5389] loading ro2 table from EEPROM to DTCM
[*05/01/2021 05:44:21.5389] 12240 bytes copied from RHL EEPROM to DTCM
[*05/01/2021 05:44:21.9779] uniphy autoneg time out!
[*05/01/2021 05:44:22.6905] ip6_port srcr2, ip6local fe80::72f0:96ff:fe06:56a8, ip6 ::, plen 0, gw6 ::, gw6_mac 00:00:00:00:00:00, mtu 1500, vid 0, mode6 2(slaa c)
[*05/01/2021 05:44:27.3269] device aptrace0 entered promiscuous mode
[*05/01/2021 05:44:27.3768] device to_container entered promiscuous mode

[*05/01/2021 05:44:27.6879] chpasswd: password for user changed
[*05/01/2021 05:44:27.7268] DOT11_TXP[0]:Domain configured: 12 class:E

User Access Verification
Username: [*05/01/2021 05:44:31.3186] flags value is 0
[*05/01/2021 05:44:31.3424] DOT11_TXP[0]:Domain configured: 12 class:E
[*05/01/2021 05:44:31.3574] Reset chip in progess, not resetting
[*05/01/2021 05:44:33.0542] Error: Socket open failed
[*05/01/2021 05:44:35.6307] Error: Socket open failed
[*05/01/2021 05:44:35.6325] IOT Bootloader Flash Tool 1.4
[*05/01/2021 05:44:35.6325] Firmware upgrade initiated by ble_management
[*05/01/2021 05:44:35.6325] Opening serial console to.. /dev/ttyMSM1
[*05/01/2021 05:44:35.6325] bundled_fw_ver = ['Lodestar', '2.7.16']
[*05/01/2021 05:44:35.6325] RSP: 04FF10FF070002150AFF020710320000000000
[*05/01/2021 05:44:35.6325] ls_ver = 2.7.16
[*05/01/2021 05:44:35.6325] ls_fw_ver 2.7.16
[*05/01/2021 05:44:35.6325] upgrade false
[*05/01/2021 05:44:35.6325] FW version is latest. No need to upgrade
[*05/01/2021 05:44:35.7121] DOT11_TXP[0]:Domain configured: 1 class:E
[*05/01/2021 05:44:36.0199] ethernet_port wired0, ip 192.168.1.216, netmask 255. 255.255.0, gw 192.168.1.1, mtu 1500, bcast 192.168.1.255, dns1 192.168.1.1, vid 0, static_ip_failover false, dhcp_vlan_failover false
[*05/01/2021 05:44:36.4777] DOT11_DRV[0]: Init Radio0
[*05/01/2021 05:44:36.5142] wlan: [5657:I:ANY] acfg_set_chan: 988: VAP is not re ady. Saving channel [6] to configure later
[*05/01/2021 05:44:36.5146] DOT11_DRV[0]: set_channel Channel set to 6
[*05/01/2021 05:44:36.5227] DOT11_DRV[1]: Init Radio1
[*05/01/2021 05:44:36.5492] DOT11_DRV[1]: Stop Radio1 - Begin
[*05/01/2021 05:44:36.5513] DOT11_DRV[1]: Stop Radio1 - End
[*05/01/2021 05:44:36.5677] wlan: [5657:I:ANY] acfg_set_chan: 988: VAP is not re ady. Saving channel [36] to configure later
[*05/01/2021 05:44:36.5678] DOT11_DRV[1]: set_channel Channel set to 36
[*05/01/2021 05:44:36.5700] DOT11_DRV[2]: Init Radio2
[*05/01/2021 05:44:37.1855] wlan: [5657:I:ANY] acfg_set_chan: 988: VAP is not re ady. Saving channel [1] to configure later
[*05/01/2021 05:44:37.1858] DOT11_DRV[0]: set_channel Channel set to 1
[*05/01/2021 05:44:37.1883] wlan: [5657:I:ANY] acfg_set_chan: 988: VAP is not re ady. Saving channel [1] to configure later
[*05/01/2021 05:44:37.1887] DOT11_DRV[0]: set_channel Channel set to 1
[*05/01/2021 05:44:37.1941] wlan: [0:I:ANY] ol_ath_twt_disable_complete_event_ha ndler: 14954: twt disabled.
[*05/01/2021 05:44:37.1941]
[*05/01/2021 05:44:37.1976] DOT11_DRV[0]: Channel set to 1, width 20
[*05/01/2021 05:44:37.2004] DOT11_DRV[0]: Channel set to 1, width 20
[*05/01/2021 05:44:37.2154] wlan: [5657:I:ANY] acfg_set_chan: 988: VAP is not re ady. Saving channel [36] to configure later
[*05/01/2021 05:44:37.2157] DOT11_DRV[1]: set_channel Channel set to 36
[*05/01/2021 05:44:37.2245] wlan: [5657:I:ANY] acfg_set_chan: 988: VAP is not re ady. Saving channel [36] to configure later
[*05/01/2021 05:44:37.2249] DOT11_DRV[1]: set_channel Channel set to 36
[*05/01/2021 05:44:37.2279] DOT11_DRV[1]: Channel set to 36, width 20
[*05/01/2021 05:44:37.2405] DOT11_DRV[1]: Channel set to 36, width 20
[*05/01/2021 05:44:37.2704] wlan: [0:I:ANY] ol_ath_twt_disable_complete_event_ha ndler: 14954: twt disabled.
[*05/01/2021 05:44:37.2704]
[*05/01/2021 05:44:46.4261] AP IPv4 Address updated from 0.0.0.0 to 192.168.1.21 6
[*05/01/2021 05:46:00.8453] AP is in good condition, BLE is off
[*05/01/2021 05:46:00.8453] Set radio wifi0 power 4 antenna chain 4 15
[*05/01/2021 05:46:00.8453] Set radio wifi1 power 4 antenna chain 8 255
[*05/01/2021 05:46:10.9242] dtls_init: Use SUDI certificate
[*05/01/2021 05:46:10.9270]
[*05/01/2021 05:46:10.9270] CAPWAP State: Init
[*05/01/2021 05:46:15.0605] Start: RPC thread 2816476048 created.
[*05/01/2021 05:46:15.0605] PNP:Server not reachable, Start CAPWAP Discovery
[*05/01/2021 05:46:15.0611]
[*05/01/2021 05:46:15.0611] CAPWAP State: Discovery
[*05/01/2021 05:46:15.0641] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*05/01/2021 05:46:15.0645]
[*05/01/2021 05:46:15.0645] CAPWAP State: Discovery
[*05/01/2021 05:46:15.0664] Discovery Response from 192.168.1.45
[*01/01/2025 11:28:47.0003]
[*01/01/2025 11:28:47.0003] CAPWAP State: DTLS Setup
[*01/01/2025 11:28:47.4182] sudi99_request_check_and_load: Use HARSA SUDI certificate
[*01/01/2025 11:28:47.7651]
[*01/01/2025 11:28:47.7651] CAPWAP State: Join
[*01/01/2025 11:28:47.7707] Sending Join request to 192.168.1.45 through port 5272
[*01/01/2025 11:29:44.0456]
[*01/01/2025 11:29:44.0456] CAPWAP State: DTLS Teardown
[*01/01/2025 11:29:44.1701] upgrade.sh: Script called with args:[ABORT]
[*01/01/2025 11:29:44.2031] do ABORT, part1 is active part
[*01/01/2025 11:29:44.2258] upgrade.sh: Cleanup tmp files ...
[*01/01/2025 11:29:44.2500] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*01/01/2025 11:29:44.2501] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*01/01/2025 11:29:58.8050]
[*01/01/2025 11:29:58.8050] CAPWAP State: Discovery
[*01/01/2025 11:29:58.8221] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*01/01/2025 11:29:58.8243] Discovery Response from 192.168.1.45
[*01/01/2025 11:30:09.0002]
[*01/01/2025 11:30:09.0002] CAPWAP State: DTLS Setup
[*01/01/2025 11:30:09.3819]
[*01/01/2025 11:30:09.3819] CAPWAP State: Join
[*01/01/2025 11:30:09.3885] Sending Join request to 192.168.1.45 through port 5272
[*01/01/2025 11:31:06.0433]
[*01/01/2025 11:31:06.0433] CAPWAP State: DTLS Teardown
[*01/01/2025 11:31:06.1331] upgrade.sh: Script called with args:[ABORT]
[*01/01/2025 11:31:06.1658] do ABORT, part1 is active part
[*01/01/2025 11:31:06.1869] upgrade.sh: Cleanup tmp files ...
[*01/01/2025 11:31:06.2096] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*01/01/2025 11:31:06.2097] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*01/01/2025 11:31:20.7956]
[*01/01/2025 11:31:20.7956] CAPWAP State: Discovery
[*01/01/2025 11:31:20.8028] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*01/01/2025 11:31:20.8045] Discovery Response from 192.168.1.45
[*01/01/2025 11:31:30.0004]
[*01/01/2025 11:31:30.0004] CAPWAP State: DTLS Setup
[*01/01/2025 11:31:30.3553]
[*01/01/2025 11:31:30.3553] CAPWAP State: Join
[*01/01/2025 11:31:30.3576] Sending Join request to 192.168.1.45 through port 5272
[*01/01/2025 11:31:39.0883] Restarted PnP Discovery timer after time sync for 60 seconds

[Rich R]

Correct - you cannot join an AP running 8.10.130.0 to a controller running 17.9.x.

This is documented in the release notes:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-9/release-notes/rn-17-9-9800.html#Cisco_Concept.dita_59a2987f-2633-4630-8c7b-a8e8aecdeaf7

Current Software	Upgrade Path for Deployments with 9130 or 9124
8.9.x or any 8.10.x version prior to 8.10.171.0	Upgrade first to 8.10.171.0 or later, 17.3.5 or later, or 17.6.x or later, and then to 17.9.x.

But your AP is not even getting to the download stage, it's failing to join the WLC at all.
So you need to check the WLC logs for the reason the join failed.
If there's nothing obvious in the logs then run a radioactive trace on the AP MAC address for more detail.

Either way you're going to need to upgrade to 8.10.171.0 or later before it will succeed.  You can try searching for those exact image names and you might get lucky.