cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
246
Views
0
Helpful
1
Replies
Dani Simanjuntak
Beginner

can't go to config (CLI) after reboot

I have convert my AIR-CAP to Autonomous

Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.3(3)JD, RELEASE SOFTWARE (fc3)

but when all of step i get stuck with this, but no warning or error

i cant config and i have wait for 15 minutes and reboot again




Press RETURN to get started!


*Mar 1 00:00:13.463: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:20.439: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:20.583: loading Power Tables from flash:/ap1g2-k9w7-mx.153-3.JD/K2.bin. Class = E
*Mar 1 00:00:20.583: record size of 3ss: 1168 read_ptr: 2DF949E

*Mar 1 00:00:26.839: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:26.915: loading Power Tables from flash:/ap1g2-k9w7-mx.153-3.JD/K5.bin. Class = C
*Mar 1 00:00:26.915: record size of 3ss: 1168 read_ptr: 2DF949E

*Mar 1 00:00:29.559: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:30.703: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:30.803: Starting Ethernet promiscuous mode
*Mar 1 00:00:30.831: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to interface reset
*Mar 1 00:00:30.839: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to interface reset
*Mar 1 00:00:30.843: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to interface is getting down
*Mar 1 00:00:30.843: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to interface is getting down
*Mar 1 00:00:30.863: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:30.863: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar 1 00:00:30.879: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.3(3)JD, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Fri 29-Jul-16 02:49 by prod_rel_team
*Mar 1 00:00:30.879: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:00:30.903: No configuration in NVRAM..Auto Install initiated..
*Mar 1 00:00:31.851: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:31.863: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:31.863: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

1 REPLY 1
Scott Fella
Hall of Fame Master

Try to use a different autonomous image.  Might be an issue with the one you installed if you can't access the CLI.

-Scott

*** Please rate helpful posts ***

-Scott
*** Please rate helpful posts ***
Content for Community-Ad