05-12-2024 03:35 AM
As of now, we are using WLC and Access Points as per the following make and model:
Cisco Aironet 1815i Access Point
Model: AIR-AP1815I-D-K9
Software Version: 8.10.185.0
Now, we have purchased new Catalyst 9100 Access Points:
AP Model number: C9105AXI-D
After configuring CAPWAP, it detects with Aironet WLC but is unable to connect with IP, and the following error occurs in the Putty connection:
[*12/16/2023 02:39:37.0000] CAPWAP State: DTLS Setup
[*12/16/2023 02:39:37.0680] dtls_verify_server_cert: Controller certificate verification successful
[*12/16/2023 02:39:37.4260]
[*12/16/2023 02:39:37.4260] CAPWAP State: Join
[*12/16/2023 02:39:37.4320] Sending Join request to 192.168.0.90 through port 5265
[*12/16/2023 02:39:42.1840] Join Response from 192.168.0.90
[*12/16/2023 02:39:42.1840] AC accepted join request with result code: 0
[*12/16/2023 02:39:42.1840] Received wlcType 1, timer 120
[*12/16/2023 02:39:42.1950]
[*12/16/2023 02:39:42.1950] CAPWAP State: Image Data
[*12/16/2023 02:39:42.1960] AP image version 17.6.4.56 backup 0.0.0.0, Controller 8.10.185.0
[*12/16/2023 02:39:42.1960] Version does not match.
[*12/16/2023 02:39:42.2820] status 'upgrade.sh: Script called with args:[PRECHECK]'
[*12/16/2023 02:39:42.3900] do PRECHECK, part1 is active part
[*12/16/2023 02:39:42.4380] status 'upgrade.sh: /tmp space: OK available 100800, required 40000 '
[*12/16/2023 02:39:42.4390] wtpImgFileReadRequest: request ap1g8, local /tmp/part.tar
[*12/16/2023 02:39:42.4420] Image Data Request sent to 192.168.0.90, fileName [ap1g8], replicaStatus 0
[*12/16/2023 02:39:42.4440] Image Data Response from 192.168.0.90
[*12/16/2023 02:39:42.4440] AC accepted join request with result code: 0
05-12-2024 09:13 AM
>...AP image version 17.6.4.56 backup 0.0.0.0, Controller 8.10.185.0
Version does not match.
- It looks like the AP has been used on the 9800 controller environments or just came with that image ; in that case going back to aireos or mobility express based platforms is not always possible. You may need to install the corresponding image manually on the C9105AXI-D access point : 15.3(3)JK9
M.
05-13-2024 09:02 AM
What comes in the logs after what you pasted in above? Does the image download and install?
As @marce1000 says you can install the image manually.
You should also upgrade the WLC to 8.10.190.0 as per TAC recommended link below.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide