Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Windows machines and 802.11r
Hi,Might not be the optimal place to ask about a Microsoft-issue, but we have many enterprise laptops running the latest windows 10 with intel wifi-cards that support 802.11r. The SSID is running FT adaptive, and iOS-devices are successfully connecte...
Hi EveryoneI'm seeing the following message in my logs every 30 seconds:396901: Apr 2 2014 13:31:20.958 BST: *capwapPingSocketTask: 1 wcm: %CAPWAPPING-3-PKT_RECV_ERROR: capwapPingSocketTask: capwappingRecvPkt returned errorDoes anyone know what thi...
Hello team ,we have a setup of C1852 as WLC and joined CAPWAP AP 9130usually the default mode for 9130 is dual mode with means slot 0 for 2.4 and slot 1 for 5 GHZi found that it operates in Tri mode which means it has slot 0 for 2.4 and slot 1 and sl...
Resolved! Cisco 9800-CL HA setup issue
Trying to setup redundancy on 9800-Cl in Esxi environment. Have three NICs - Gi1 ( OOB ) , Gi2 ( trunk ) , Gi3 ( HA ) . After issuing following commands and reloading controllers one of the controller goes into recovery mode and HA is not formed. Co...
Hi All Can anyone tell me the benefits of increasing TX power on an access point? does it allow the signal to go further? or faster etc ?
Resolved! 9120AX login fails after reset
Hi all and thanks in advance for any advice.I have had the same issue now with two 9120AX APs where following a hard reset, pressing the reset button for longer than 20 seconds, I'm unable to login to the device either by SSH or console. Neither the...
[*09/04/2024 18:35:52.0000][*09/04/2024 18:35:52.0001][*09/04/2024 18:35:52.0001] CAPWAP State: DTLS Setup[*09/04/2024 18:35:52.3783][*09/04/2024 18:35:52.3783] CAPWAP State: Join[*09/04/2024 18:35:52.3797] Sending Join request to 10.48.40.45 through...
Resolved! DHCP Relay Over WAN
I have 3 flexed WLANs at a branch that will receive DHCP from Windows at our DC. I'm unsure of what to set the relay to. Is it our L3 SVI which in turn relays to the DC or do we set the relay to the IP of the Windows server at the DC? Thanks in advan...
Hello,I use external captive portal with RADIUS server on my 9800 WLC. I was using 17.6.5 and upgraded to 17.12.3. After upgraded it, on the RADIUS start packet username looks as clients MAC address, it was userxxx before. Is there any configuration ...
Resolved! What is Aironet IE? I have my clients disconnected from when uncheck the Aironet IE in WLC 5520
What is Aironet IE? I have my clients disconnected from when uncheck the Aironet IE in WLC 5520
my AP (AIR-CAP3702E-B-K9) seem to loss its firmware. attached is the startup log when trying to reset it using the mode button. any help would be much appreciatedIOS Bootloader - Starting system.flash is writableTide XL MB - 40MB of flashXmodem file ...
Hello,I've got question related to this particular debug entries (from radioactive trace):2024/04/18 13:06:43.944436 {rogued_R0-0}{1}: [rogue-capwap] [25943]: (debug): Client info (2/2), MAC:<xxxxxx>, reported by yyyyyyy, GW: 111111111, chan:40, rssi...
I'm working on getting our standards in place for Rogue AP management on 9800s and I've come across this setting that I'm struggling to understand.wireless wps rogue client notify-min-deviation 5 wireless wps rogue ap notify-rssi-deviation 5Descripti...
Hello Professionals,I got a user complaint about low quality of wireless(PDA), and when I check the connection status I got:Compared with other PDA which is connected same AP, connection speed is 72Mbps.What might cause the differences? Which configu...
Goodday all, I've read several other posts about rogue detections being send as syslog messages on AireOS, but I'm now trying to get this done at the Catalyst 9800 WLC. In summary, I want a syslog message to a SIEM server once a rogue is detected. Do...
