cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2422
Views
0
Helpful
12
Replies

Cisco AP C9115AXI-E doesn't join to WLC C9800-CL

ryosaeba86
Level 1
Level 1

Hi all,

 

I am trying to join a C9115AXI-E AP to the C9800-CL controller with no success ... 69 Outdoor APs (AIR-AP1542I-E-K9) are already associated with this controller (the MAC addresses have been entered as trust devices). Unfortunately with the indoor models (without adding MAC in the trust devices) I have problems with the join:

 

APA49B.CD26.9B1C#[*02/10/2022 09:52:49.0310]
[*02/10/2022 09:52:49.0310] CAPWAP State: DTLS Teardown
[*02/10/2022 09:52:49.1060] upgrade.sh: Script called with args:[ABORT]
[*02/10/2022 09:52:49.1450] do ABORT, part1 is active part
[*02/10/2022 09:52:49.1610] upgrade.sh: Cleanup tmp files ...
[*02/10/2022 09:52:49.1800] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*02/10/2022 09:52:49.1800] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*02/10/2022 09:53:03.7820]
[*02/10/2022 09:53:03.7820] CAPWAP State: Discovery
[*02/10/2022 09:53:03.7840] Discovery Request sent to 10.192.1.250, discovery type STATIC_CONFIG(1)
[*02/10/2022 09:53:03.7840] Got WLC address 10.192.1.250 from DHCP.
[*02/10/2022 09:53:03.7840] IP DNS query for CISCO-CAPWAP-CONTROLLER.atac.roma.it
[*02/10/2022 09:53:03.7920] Discovery Request sent to 10.192.1.250, discovery type STATIC_CONFIG(1)
[*02/10/2022 09:53:03.7980] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*02/10/2022 09:53:03.7990] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.7990] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.8000] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.8000] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.8000] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.8010] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.8010] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.8010] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:03.8010] Discovery Response from 10.192.1.250
[*02/10/2022 09:53:13.0000]
[*02/10/2022 09:53:13.0000] CAPWAP State: DTLS Setup
[*02/10/2022 09:53:13.7010] First connect to vWLC, accept vWLC by default
[*02/10/2022 09:53:13.7010]
[*02/10/2022 09:53:13.7150]
[*02/10/2022 09:53:13.7150] CAPWAP State: Join
[*02/10/2022 09:53:13.7230] Sending Join request to 10.192.1.250 through port 5267
[*02/10/2022 09:53:18.3210] Sending Join request to 10.192.1.250 through port 5267

 

AP Running Image : 8.10.130.0
Primary Boot Image : 8.10.130.0

(C9800-CL-K9_IOSXE), Version 17.3.3, RELEASE SOFTWARE (fc7)

 

I have already tried to add their MAC in the trust devices, I have restarted the WLC and configured the CAPWAPP manually.

The APs correctly receive the IP via DHCP as you can see from the attached photo.

Any suggestions?

 

Thanks,

 

 

 

 

12 Replies 12

marce1000
VIP
VIP

 

 - Start by having a configuration check of the C9800-CL , for that use (CLI) show tech wireless , have the output analyzed by : https://cway.cisco.com/tools/WirelessAnalyzer/ , make sure you don't have any red-flagged advisories. If so , they need correction (first)

 M.



-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

Here attached the output...I don't see major configuration error.

 

 

 - There are 3 red errors, but they are probably not related to your issue (indeed).  Could you also check the controller-logs when one of these ap's tries to join (just after failure issue show logging on the controller ) , or use a syslog-server.

 M.



-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

Hi,

unfortunately I didn't see any logs from Controller about the AP (when it reboot). But I confirm that the comunication between AP and WLC is ok (ping is ok, arp resolution is ok, etc).

 

 - I find that a bit suspicious , could you verify if there are logs seen on the controller, if one of the working AP's join ? If that would be the case it would even more point to some kind of problem (?)

 M.



-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

No, also for the other APs I don't see any logs.

But for them everything is ok...

 

-  Does the regulatory domain of these AP's match the controller settings  ? Also could you factory reset one of the C9115AXI-E (nothing else) and  try again.

 M.



-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

Factory Reset already done, about the regulatory domain I will check.

Thanks

Scott Fella
Hall of Fame
Hall of Fame

Well you existing AP's are "E" and the 9115 is an "E" so that should be okay.  Make sure you have the mac address correct, look at the switch cdp neighbors to validate that.  The 9115 is supported on that code version, so the only thing I can see that is wrong is the controller is not allowing the join due to the mac address not in the list.  Just double check that again.

Also, look at the complete ap output from when you boot it up until it reboots to try to discover that controller again.  You can also run some debugs for the ap join on the controller.

-Scott
*** Please rate helpful posts ***

Hi,

thanks for the reply.

About MAC do you refer the MAC Address for Trust device in AAA section or the MAC for insert the tag on AP?

Also I have a second question ... when a new AP is associated with the WLC 9800-CL are automatically assigned the default tags or do you necessarily have to enter its MAC address and then add the desired ones?

Thanks,

For your second question, you can use filters to automatically assign tags.

filters.jpg

-Scott
*** Please rate helpful posts ***

For your 1st question, take a look at this link.  This is a guide for outdoor access points that will join a 9800 controller.

Configure Mesh on Catalyst 9800 Wireless LAN Controllers - Cisco

-Scott
*** Please rate helpful posts ***
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: