Configuring AppleTV for Wireless deployment without WLC (881->3560->AP)

[ElwinMkanyika]

Hi Guys,

I have read the Wirelss deployment guide provided but i do not seem to get AppleTV to work on the wireless network. When connected to the wired network - all is ok.

Design -

Cisco 881 -> 3560 -> AP

Here is what i have so far:

Router Config:

ip multicast-routing

no ip igmp snooping

interface FastEthernet0

switchport mode trunk

!

interface FastEthernet1

switchport access vlan 5

!

interface FastEthernet2

switchport access vlan 5

!

interface FastEthernet3

switchport access vlan 5

!

interface FastEthernet4

mac-address *****

ip address *****

!

interface Vlan1

ip address 192.168.0.5 255.255.255.0

ip pim sparse-dense-mode

!

interface Vlan5

description --Data--

ip address 192.168.5.254 255.255.255.0

ip pim sparse-dense-mode

!

interface Vlan6

description --Media--

ip address 192.168.1.254 255.255.255.0

ip pim sparse-dense-mode

Switch config

A-01#sh run

ip igmp snooping querier

vlan internal allocation policy ascending

!

vlan 5

name Data

!

vlan 6

name Media

!

interface GigabitEthernet0/1

description <<To_G-01>>

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 1,5,6

switchport mode trunk

switchport nonegotiate

interface Vlan1

ip address 192.168.0.223 255.255.255.0

ip pim rp-address 192.168.5.254

!

AP Configuration

no ip igmp snooping

no dot11 igmp snooping-helper

Please help me properly configure the network to support AppleTV. We currently use vlan 5 and 1 only. vlan 1 is management and vlan 5 - basically data and media.

Regards,

Faith

[Scott Fella]

What code are you running on the AP? I have had some peers upgrade to v15 and broke their bonjour. Having the firmware at v12 works.

Sent from Cisco Technical Support iPhone App

[ElwinMkanyika]

Scott,

Thank you for your time.

I hope you do not mind my rather uneducated answer:

How do i find out the code that i am running on the AP?

[Scott Fella]

Show version and then post that. That will show you the version the AP booted.

You can also issue a show boot from the CLI and also a show dir to show the flies

Sent from Cisco Technical Support iPhone App

[ElwinMkanyika]

Am used to it being called IOS

Here we go.

flash:/c1140-k9w7-mx.152-2.JB/c1140-k9w7-mx.152-2.JB

You believe I should downgrade to v12?

Could we first confirm that the configuration is ok so that i can resort to downgrade as a last resort because the AP is in exploitation at the client's site.

Could you please confirm that my multicast configurations are correct ?

Thank you for your time Scott!

Faith.

[Scott Fella]

The configurations look fine from what I also have read on the forums.  I just know the v15 has broke the bonjour stuff.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

[ElwinMkanyika]

Thank you Scott!

Will try downgrade then get back to you! Thank you for your replies.

Reagrds,

Faith

[Scott Fella]

Let me know how it goes.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

[ElwinMkanyika]

Hello Scott!

So I finally got to  downgrade to v12 but appleTV is still not working

Any more suggestions?

Faith

[maldehne]

try to enable ip igmp snooping-helper command on the AP

how it goes ??