Continuous Boot AP
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-30-2024 04:25 AM
My AP device has this problem of constantly booting up.
Meraki Mode Selected
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 242 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 970, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 0
ubi0: available PEBs: 886, total reserved PEBs: 84, PEBs reserved for bad PEB handling: 80
Secure boot enabled.
Read 0 bytes from volume part.safe to 50000000
Volume part.safe not found!
Read 0 bytes from volume part.old to 50000000
Volume part.old not found!
resetting ...
ûvïgsOCóîæþ^ÒBÊBþËÒÒËÚËÚËÚ^cÒZÒfSwFRËR~RîCÞËÚÃÒËÒÒþÂkÚËÒÃGVcÒêkûÒzKÒcÂÖËVÇRRWßÒÆ~ÒÆ~BrÃÞËÖGâÓRæËRÎËVRæBæËâÒæÒîËVÒæËÒcÃG^ËRòËVÒÎËÂÒæËÂgÒZÒZrÇÇWo×o÷ÚVVÆËãöóæNç~ÚökþÇrJ÷ëßòïoÿok{
U-Boot 2018.01-RELEASE-gc2c29d24b7 (May 05 2023 - 09:28:10 -0700)
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
Device Tree: QCA, IPQ807x-CM66
machid: 8010001
Net: No ethernet found.
Autoboot in 5 seconds
- Labels:
-
Catalyst Access Points
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-30-2024 06:27 AM
Can I access the Meraki dashboard to push down the firmware while the AP is in this boot state?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-30-2024 06:33 AM
No.
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390

- « Previous
-
- 1
- 2
- Next »