Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

New firmware release notes.Important noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will upgrade to the backup version (MR 30.7.1...

tyshawn76 by • Level 7
  • 6387 Views
  • 2 replies
  • 3 Helpful votes

We are looking to implement a zero trust through ThreatLocker and therefore we would like to find out which ports on the WLC need to be able to communicate with our domain controllers, our radius server, and with the APs. I have already looked at the...

jmorton1 by • Level 3
  • 4216 Views
  • 10 replies
  • 0 Helpful votes

お世話になっております。WLC9800-40(17.15.2)を利用しているのですが、MACアドレスフィルタリングに登録していたはずのMACアドレスが消えていました(すべてではなく1つのMACアドレスのみです)認証ログからおおよその日時を特定したのですが、休日帯であり、WLCは一切操作しておりません。原因が分かる方・同様の事象に遭われた方いらっしゃいますか?

Yuki T by • Spotlight
  • 974 Views
  • 5 replies
  • 0 Helpful votes

Hello,two years ago  I described a ROMMON and Ethernet Phy Upgrade on our 9800-L-C HA-Bundle.https://community.cisco.com/t5/wireless/9800-l-c-in-ha-rommon-and-ethernet-phy-upgrade/m-p/4996695#M265310Today, in preparation for a SW-Upgrade, to my surpr...

Gehrig_W_1-1678874920393.png Gehrig_W_3-1678875004906.png Gehrig_W_0-1756458611143.png
Gehrig_W by • Level 6
  • 3257 Views
  • 17 replies
  • 0 Helpful votes

Has the 150ax been abandoned? The current firmware is 10.6.2.0 from 2023. The 140/145 have 10.10 from 2024.I find it hard to believe there's been nothing worth patching in two years.

Hi,We have two SSID's, one corporate SSID with 8021x(EAP-TLS) and the second is Guest SSID anchored back to DMZ.This is standard configuration present at around 1000 sites.Company phones are managed by MDM and connect to corporate SSID doing EAP-TLS,...

Is there any way to  restrict the bandwidth usage Guest wireless users in Cisco DNAC. any pointers to configuration example or article will be good. If it is not possible in DNAC, can we achieve this in WLC.    

Arunr by • Frequent Visitor
  • 1466 Views
  • 6 replies
  • 0 Helpful votes

Hello team, I have some weird problem on few access points connected to L3 switch. This is situation: L3 switch is DHCP for few access points connected directly to it. ip dhcp pool VLAN75_WIFI_MGMTnetwork 10.2.75.0 255.255.255.0default-router 10.2.75...

zeljkosan by • Level 3
  • 4188 Views
  • 14 replies
  • 0 Helpful votes

Hi everyone, As the title said, we just purchased 9163E-E and attached them to our WLC 9800 but their operationnal status are still down. For the record, we had to upgrade our WLC to 17.12.5 to avoid any compatibility mismatch. Now the AP have joined...

AK59 by • Level 3
  • 2508 Views
  • 5 replies
  • 0 Helpful votes

Hi all,I’m having a consistent issue with wireless event logs, the first 802.1X authentication attempt each morning is missing the client_ip. Simply disconnecting and reconnecting the client fixes it, and all subsequent log entries include the client...

image.png
jd-1607 by • Community Member
  • 1716 Views
  • 3 replies
  • 0 Helpful votes

Hi,Following is the requirement Guest Wi-Fi for external users: 1. User must be authenticated with MFA. User can be pre-defined with email/mobile.2. Authentication must NOT be on AD or ISE.3. External captive portal can be used. Separate auth server ...

Hello,I have mistakenly installed CAPWAP image on the WP-WIFI6 WIM module on my IR1821. I am now unable to install the UIW image that contains the WGB capabilities. The archive download-sw loads the image, but refuses to accept it. It prints the foll...

Review Cisco Networking for a $25 gift card