11-15-2014 11:51 AM - edited 07-05-2021 01:56 AM
I have a Cisco Aironet 3702E and I want to configure it as standalone unit in my network. This AP is a brand new and has not been deployed in a network and has not been controlled by an AC previously. I have tried to find out how to enable HTTP on this AP but in vain. And also when I try to execute any command in enable mode I get the following error message:
AP58f3.9c39.118b#capwap ap hostname CAP3702E
ERROR!!! Command is disabled.
Appreciate if you can point to any documentation that might help to configure this AP in ROOT mode and enable HTTP and configuration of this device.
Cisco IOS Software, C3700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Sat 16-Nov-13 10:46 by prod_rel_team
ROM: Bootstrap program is C3700 boot loader
BOOTLDR: C3700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB, RELEASE SOFTWARE (fc1)
AP58f3.9c39.118b uptime is 1 hour, 39 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
Last reload reason:
cisco AIR-CAP3702E-E-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FCZ1833J090
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.1.118
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 58:F3:9C:39:11:8B
Part Number : 73-15397-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18255VCM
Top Assembly Part Number : 068-05055-01
Top Assembly Serial Number : FCZ1833J090
Top Revision Number : A0
Product/Model Number : AIR-CAP3702E-E-K9
Solved! Go to Solution.
11-15-2014 03:09 PM
AP58f3.9c39.118b#capwap ap hostname CAP3702E
ERROR!!! Command is disabled.
Your AP is running controller-based IOS. You need to convert it to load autonomous IOS.
11-15-2014 03:09 PM
AP58f3.9c39.118b#capwap ap hostname CAP3702E
ERROR!!! Command is disabled.
Your AP is running controller-based IOS. You need to convert it to load autonomous IOS.
11-17-2014 07:02 AM
Thanks. The Cisco Partner that have sold this AP to us has not provided the right software.
It is strange. I have purchased a brand new AP, but I cannot download software from Cisco. I should have a service Contract.
Kind regards,
Sam
11-19-2014 01:21 AM
HI Sam,
Check this video from jerome Henry regarding this error:
http://www.youtube.com/watch?v=H7nVFT7l7ug
Also try this:
debug capwap console cli
erase /all nvram:
reload
Regards
Dont forget to rate helpful posts
11-22-2014 02:38 AM
Hi,
many thanks. The issue was related to wrong software was shipped with the AP. Unfortunately, there is no channel to complain about this. We contacted ATEA which is Cisco Gold Partner in Sweden. Initially, they were reluctant to help us in spite of we had asked for an autonomous AP. Later, they agreed to provide software, but then it was like we-are-doing-you-a-favor. It is really strange.
Kind regards,
Sam
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide