Error in GUI of Cisco 3850 Switch with Wireless Controller.

Ninad Thakare · ‎02-20-2014

Hi,

I have Configured 3850 switch wireless controller. But while accessing the controller through GUI, I faced following errors while configuring it through GUI.

Because its complecated to configure it through CLI.

Attached are the snaps of error faced.

and if I didnt get this error, and able to configure, I can save it because of this error.

Please help me on this issue, so that I can easily configure the controller.

Brgds,

Ninad Thakare

Sandeep Choudhary · ‎02-20-2014

did you enabled the https and hhtps ?

ip http server

ip http secure-server

I would first like to confirm that everything is in place for the web interface to work properly. Please provide me the following output from the CLI of the switch:

show run | i wsma

show run | i http

Additionally, have you attempted to configure the management through the CLI via 'wireless management interface ' ?

Regards

Ninad Thakare · ‎02-20-2014

Hi Sandeep,

Here is the configuration which I have did.

ip http server

ip http secure-server

wsma agent exec

profile httplistener

profile httpslistener

wsma agent config

profile httplistener

profile httpslistener

wsma agent filesys

profile httplistener

profile httpslistener

wsma agent notify

profile httplistener

profile httpslistener

!

wsma profile listener httplistener

transport http

!

wsma profile listener httpslistener

transport https

wireless mobility controller

wireless management interface Vlan4 ( Voice VLAN )

wlan FG-WiFi 1 FG-WiFi

client vlan 4

ip dhcp server 10.106.72.1

no security wpa akm dot1x

security wpa akm psk set-key ascii 0 testing1234

no security wpa wpa2

no security wpa wpa2 ciphers aes

no wmm

no shutdown

wlan GLOBALACCESSII 2 GLOBALACCESSII

client vlan 4

ip dhcp server 10.106.72.1

no security wpa akm dot1x

security wpa akm psk set-key ascii 0 testing1234

no security wpa wpa2

no security wpa wpa2 ciphers aes

no wmm

no shutdown

ap group default-group

ap group 3850WLC

wlan FG-WiFi

vlan 4

wlan GLOBALACCESSII

vlan 4

end

Brgds,

Ninad Thakare

Sandeep Choudhary · ‎02-20-2014

Try to Connect to gigabitethernet0/0 and then set the IP address.

Connect gig0/0 to your laptop and assign IP on your computer and gig0/0 in same subnet.

Then try to access: http://IP/wireless

More check here:

https://supportforums.cisco.com/docs/DOC-34542

http://mrncciew.com/2013/09/29/getting-started-with-3850/

Regards

Dont forget to rate helpful posts

Rasika Nayanajith · ‎02-20-2014

Hi Ninad,

3850 GUI is still not that stable, get used to CLI configuring those IOS based controllers untill GUI is rock solid.

Here are some referenceblog post related to 3850 configs

http://mrncciew.com/category/3850/

HTH

Rasika

*** Pls rate all useful responses ****

Ninad Thakare · ‎02-20-2014

Hi,

I saw the site and did my all configuration an that basis only. But now I need to configure RADIUS server group and assign it to my SSID. Which is not mentioned in the mrncciew.com site, and thats why accessing to the GUI to see the options but I am not able to see due to the above error.

BTW are reffering to the MANAGEMENT port at the back side of the switch, because I dont see any GI0/0 port on the switch.

Brgds,

Ninad

Rasika Nayanajith · ‎02-20-2014

Hi Ninad,

In this post I have explained how to configure RADIUS server (used ISE as example,but it can be any RADIUS server). It should be useful if you are looking for that

http://mrncciew.com/2013/12/06/wlan-config-with-3850-part-2/

HTH

Rasika

**** Pls rate all useful responses ****

Ninad Thakare · ‎02-21-2014

Hi Rasika,

Did what you have mentioned as well as followed the link :

http://www.cisco.com/c/en/us/support/docs/wireless/5700-series-wireless-lan-controllers/116600-config-eap-radius-00.html#anc7

But I am not able to connect and pop-up with a error -

authentication failed for client (MAC) on interface ca1 AuditSessionID

Brgds,

Ninad Thakare