Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I purchased two licenses. One that's for 250 AP's, the other is for 50 AP's. I have two 5508's that I'd like to apply these license files to. Is there any way to split the 250 licenses into two 125 licenses, and the 50 licenses into two 25 license...
I have much problem with mi cisco 2504. I update software version 7.4 for use 1600 ap series. I have 5 license. I create a wlan but after a short time disappear from the wireless sensing. The access point also records disappear from the controller. I...
I'm coming across situations where a client is seeing unusable, low signal levels. What should happen, as I understand things, is the that LAP should increase it's power outage to compensate, but this isn't happening. Is this because the "WIRELESS > ...
Hello! quick question regarding MESH deployments with 2 different sorts of AP´s: AC and non-AC modells: If my 3702i is my root AP´s, and 3602i my MAP - will AC still work in 80Mhz, or will I have to switch to 40mhz (and thus crippling (???) AC perfor...
Hello,I have recently been adding a number of installed APs to heatmaps in NCS and am very confused as to the correct Azimuth and Elevation settings.In particular - if the AP is mounted on a wall rather than a ceiling what should the settings be ( an...
Resolved! Cisco Outdoor Wireless Deployment Modes
Hi,I'm looking at deploying Cisco 1552s in point to multipoint mode. I would like to know if its possible to connect wireless clients directly to the the mesh AP when in point to multipoint mode? From the documentation (Listed below), Wireless Backha...
Hi All, We are planning to take ISE SNS-3415-K9 appliance for 2500 wireless end points. Can you please guide me how to take license? Base lances are really required for wireless end points?? Your early response will be highly appreciated. Regards,...
Hi There, I've got 2 Anchor WLC's and a couple of Foreign WLC's. All of them are setup in the same mobility domain.As far as I know clients which are anchored to one of the two Anchor WLC's are load balanced on a round robin fashion towards the A-WLC...
Hello, I have recently configured vWLC and added a cisco AP. Also configured TACACS to get WLC autheticated through it. I am able to login on WLC through TACACS but i also want WLAN connection too get authenticated through this. So it is possible t...
Hi, i would like to know if i could use the cisco 3850 as a pass through to register with cisco 5508 (flex connect) at our main site. at the moment i can see the AP registering to cisco 3850 and not 5508. if i plug in the ap to a cisco 2960 will conn...
I need to see if a file is on the 5508 wlc. What is the command to show the contents of flash? Switch = sho disk0:
Dear Team, This is regarding the Cisco WLC 2504. Presenlty I have version 7.0.220, I want to upgrade to 7.4.121, So I want to know can I directly upgrade to 7.4 or I have to upgrade some middle version and then go to 7.4. Also, need to consider anyth...
Customer environment in one location is a mix of 3502i and 3602i LAPs. Customer is running wIPS Monitor Mode APs (not ELM). The answer to this question may be obvious, but wanted to get some feedback. In this environment would it be better to have th...
I have a friend I am trying to help out. here is the situation. THey have a cisco 5500 series wireless controller now, not sure what they were using before. They have a Lantronix device that allows them to print from their iphone. Since putting in ...
Hi,please, I need to know if WLC AIR-CT5508-12-K9 supports the folowing model off Access point: AIR-LAP1131-A-K9, AIR-LAP1242G-A-K9, AIR-BR1310G-A-K9, AIRCAP-16021-A-K9Thanks
