Got CPU peak when using connect around 330 user.

[ittichai_a]

  Hi all

I have implement VM-WLC with 30 AP License , we got user around 330 device to accosiated. I found that CPU reach about 72-80 % that make WLC hang. So,  i found some message below i don't sure that what is the meaing. Please give me the idea.

apfOrphanSocketTask: Jun 29 13:14:05.842: #IPV6-3-INVALID_ADDR_ORPHAN: ipv6_net.c:715 Invalid ipv6 address ::, failed to do data gleaning.

*spamApTask3: Jun 29 13:13:01.182: #LWAPP-3-VENDOR_SPEC_ERR: spam_lrad.c:12845 The system has failed decoding vendor specific payload

*spamApTask3: Jun 29 13:12:58.110: #CAPWAP-3-SEM_RELEASE_ERR: capwap_ac_db.c:106 The system could not release exclusive access of AP entry for 0c:68:03:ae:21:e0 in the database

Jun 29 13:12:56.599: [ERROR] ews.c 871: ewsRun: Bad State - should be suspended: 0x0

*DHCP Client Task: Jun 29 13:08:03.470: #DHCP-3-BIND_SRPORT_ERR: dhcp_support.c:373 Binding service port failed.

Please help

Thanks

[Scott Fella]

Some of the errors require looking at the other parts of the log. If you don't require ipv6 then disable it

config ipv6 {enable | disable}

Also do you have the requirement on your vWLC as far as CPU and Memory?

Sent from Cisco Technical Support iPhone App

[ittichai_a]

HP DL 380p G8 : 1 CPU 8C E5-2690 2.9GHz, Memory 128 GB, Disk 6x600GB 15K SAS Disk 1 x Ethernet 1GbE 4Port, 2x1200W CS Plat PL HtPlg Pwr Supply)	1
HP DL380p Gen8 8-LFF CTO Server	1
Asia Pacific-English Localization	1
HP DL380p Gen8 E5-2690 FIO Kit	1
HP 16GB 2Rx4 PC3-12800R-11 Kit	8
HP 600GB 6G SAS 15K 3.5in SC ENT HDD	6
HP 12.7mm SATA DVD ROM Jb Kit	1
HP Ethernet 1GbE 4P 331FLR FIO Adptr	1
HP 512MB FBWC for P-Series Smart Array	1
HP 2U LFF BB Rail Gen8 Kit	1
HP 1200W CS Plat PL HtPlg Pwr Supply Kit	2
HP Raid 5 Drive 1 FIO Setting	1
HP 3y 4h 24x7 DL38x(p) HW Support	1
HP Insight Control ML/DL/BL Bundle E-LTU	1

Hi Scot

This is our spec, in my idea i think that it have some message sent to vmwlc that make get high cpu. But i really don't know what is the main message or any thing elas.

Thanks

[Scott Fella]

The specs for the server is fine, but how about the vWLC VM specs? If this a consistent issue you might want to open a TAC case. There would most liken want to see the logs and configuration.

Sent from Cisco Technical Support iPhone App

[ittichai_a]

Hi Scott

vWLS is version 7.4.100 (Standard VM), it is the .ova file. I may open tac for the get real result again. But if you have any comment , please let me know.

Thanks

V

[Scott Fella]

Well the thing is that I don't know if you have everything configured right. But looking at this error

*DHCP Client Task: Jun 29 13:08:03.470: #DHCP-3-BIND_SRPORT_ERR: dhcp_support.c:373 Binding service port failed.

Looks like you created a service port and that service port is connected to a vSwitch that has connectivity to the management interface. Make sure that the service port is either on its own vSwitch that is not use/connected or to a nic that is not connected.

I would go over the deployment guide again and make sure everything on the VM is setup correctly.

http://www.cisco.com/en/US/products/ps12723/products_tech_note09186a0080bd2d04.shtml

Sent from Cisco Technical Support iPhone App

[ittichai_a]

Hi scott

i had not configure service port. I only configure management interface and client interface. There connected with the same vSwitch.

thanks scott

V

[Scott Fella]

Okay then open a TAC case because the one error shows an issue with the service port.

Sent from Cisco Technical Support iPhone App