03-12-2019 09:29 AM - edited 07-05-2021 10:02 AM
if i connect to laptop or i phone some time give me internet connection but some time not there is connection limit and some time connect only to my laptop but phones its connect but no internet i will provide my setting
Note : only now i use one ap after i solve the issue for this ap i want to put 4 ap for each floor i have 3 floor
did i need to configure any setting from main router 192.168.1.1 and i have POE switch for each floor please advice and provide me correct setting if there is any thing wrong and after that i want to enable security for my all wifi
Regard's
here is my setting i try to change channel and power i dont know where the problem actually from dns or from the firmware
! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ap4 ! logging rate-limit console 9 enable secret 5 $1$jWVb$.jDoKc5dMHuFfTD/Fe.B60 ! no aaa new-model no ip domain lookup ! ! dot11 syslog ! dot11 ssid AAM vlan 1 authentication open guest-mode ! ! ! username ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache shutdown ! ssid AAM ! antenna gain 0 power local 11 power client 11 channel 2462 station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache ! ssid AAM ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-below channel dfs station-role root no dot11 qos mode ! interface Dot11Radio1.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface BVI1 ip address dhcp client-id GigabitEthernet0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! ! ! line con 0 line vty 0 4 login local ! end
03-12-2019 03:07 PM
Hi
You do not want special config on switch/router side where these AP connect. Then can be any vlan that provide IP via DHCP. AP & wireless clients will get IP addresses from that vlan.
Simple configuration like below may work well. (pls change admin username/password from default Cisco/Cisco)
conf t
hostname <AP_HOSTNAME>
!
dot11 ssid <SSID_NAME>
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii <SSID_PASSWORD>
!
interface Dot11Radio0
encryption mode ciphers aes-ccm
ssid <SSID_NAME>
no shutdown
!
interface Dot11Radio1
channel width 40-above
encryption mode ciphers aes-ccm
ssid <SSID_NAME>
no shutdown
!
interface BVI1
ip address dhcp
!
end
write memory
HTH
Rasika
*** Pls rate all useful responses ***
03-12-2019 05:39 PM
The bro for replay i will try and tell you about channel and radio setting i keep it default and what about other APS in same floor each floor i have 4 aps
thank you very much
03-12-2019 11:08 PM
why i have problem with connecting some devices connection show limited no internet access did i have to configuration any setting in main router 192.168.1.1 and i have to separate the class range for aps devices in other building note i have use all class c
03-12-2019 11:53 PM
i have try setting above but ssid name not broadcast i have maybe attach vlan connection to ssid
and another question in your setting showing two ssid only i need one please help me
03-13-2019 03:54 PM
Hi
In my configuration, it got only one SSID. You have to replace <SSID_NAME> with whatever name you like.
There are two radio interfaces (radio 0 & radio 1 which are 2.4GHz & 5.0GHz), you have to configure SSID under radio interfaces if you want those radio to advertise that SSID name.
Take one AP & erase existing config, then simply put config I suggested & then plug it to DHCP capable port on your modem. Then test
Later on when you deploy multiple AP, you can plan a channel & assign AP to different channel without interfering with each other.
HTH
Rasika
*** Pls rate all useful responses ***
03-13-2019 07:09 PM
Thank you bro for your answer
i got it but i have important question
if ihave 16 aps cisco autonomous for each floor there is 4 aps did i need to configure switch port and trunk with vlans in aps or no need just installing with different hostname and channel only because before when i try to put 4 access point in 1st floor only internet work with 1 device other devices is connected but not give internet or some time is tell page connot found for all iPhone or mobile devices can you clear this points to me before start boss and thanks
03-14-2019 12:27 AM
03-14-2019 04:35 AM
Hello
first i have config 4 aps for 1st floor example:
ap1 Use vlan 1
ap2 use vlan 2
ap3 use vlan 3
same ssid name and security i didn’t configure switch its default
so can i use the four access point in 1st floor only with vlan 1 for all aps it will work or not perfect or i disable the vlans on all wifi
and if i want to config switch how can access the switch because this first time for me
if there is simple way let me know boss ty
03-14-2019 08:23 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide