Hi everyone,In AireOS WLC, we used be modify the Wireless Option "Client Roaming" parameters for solving some client's roming problem. But after migration to C9800 , the Wireless Option "Client Roaming" is gone .My question is:1/ Is there any funct...
Hey all, wanted to make sure I am on the right track for disabling both the SSL 3rd party cert and disabling the acceptance page for our guest network. The reasoning behind disabling the 3rd party cert is because after upgrading our Entrust cert bac...
Hello Team,Do we have standard WLC sizing guide specially for bandwidth related to management traffic for Cisco WLC.. the requirement is WLC is remote and our company is going to take management of WLC, before that.. they want to know the managment t...
Hello i have Cisco Virtual Wireless Controller with version 8.9.111.0 and i have 13 acces point 1815i cisco but the problem that only access point 1815i is not discovred by wlcV and all 13 AP are same version 8.5.140 . so wlcV can dico...
Hi! I am new configuring this type of WLAN. I got my AP/WLC in place. But all my AP's are set as WLC as well. How do I get them to just be AP's that are depending on my first WLC ? Do I need a new firmware , Or is there a trick in the config that I ...
Hi looking for a little advice, what exactly is 'Signal Quality' shown in the attached image (taken from Cisco controller)?Is it the same as RSSI (dBm) or SNR? And what do the values on the image tell me about all three user's Wi-Fi connections? Is 0...
Hello! Customer is replacing a 2504 with two 3504 in HA. Also replacing APs 1702i with 2802i. For faster migration, software version was kept the same, 8.5.131.2504's configuration was uploaded via GUI and converted using TAC's WLC Config Converter a...
I'm installing a 1562E with an ANT2513 however I cannot find how to change the AP to use 2.4GHz on ports 1 and 2 then 5GHz on ports 3 and 4 which appears to be a requirement for this antenna. Running 8.5.161 code currently.
I have a client with AP 1552H for Hazardous environments, and 5508 WLCs, and now he needs new APs for hazardous environments, but 1552H are EoS, so the only available model is the IW6300 but it's only supported in software 8.10.105.0, and the 5508 WL...
Hi All,I was wondering if it's possible to use a passphrase for the WiFi password (PSK). Is there a limit on characters?
i have follow the CISCO config example.https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-9800-series-wireless-controllers/213924-flexconnect-wlan-with-802-1x-aaa-overrid.html one of the WLAN need to use Flex Connect setting.once i disable ...
WLC4402/4404 firmware images? This WLC is EOL and thus images are no longer available from Cisco. My lab WLC has 7.0.240 code and was hoping you may have something newer. I got my hands on a couple of 3600 series APs for my lab, but this AP is only s...
i need to know if i have two C9800 in HA mode will support a total number of 500 AP or i should purchase the performance license to reach this number
Hi All,My customers are complaining that they're being disconnected from the network on a daily basis. The disconnect lasts usually from 30 seconds to 5 minutes. I checked the logs on the MR18 and I'm seeing: Ethernet port carrier change - device: wi...
Hello,I have a wireless network built with Cisco WLC 5520 (in HA), AP 3702 and AP 3802. WLC is running code 8.5.135.0.APs are placed in the bldg. considering user density and after a proper site survey. Distance between APs is not more than 15m.When ...
