Joining 3802s to a 2504/5508/5520 after it has been on a 9800

[denneht]

Scenario:

We rented a building that already has a ceiling full of 9800s.  When we took occupancy, everyone thought the 3802s would join the 5520.  Nope.

I put a borrowed 9800-l online, and APs would join it.  Reconnect them to the network where the 5520 is, and nope.

Took a 3802 and put it on the bench with my 9800 and it joins.  Connected a 3504 and disconnected the9800.  AP joins the 3504.  Connect the 2504, and disconnect the 3504. Nope.  They won't join.

Oddly, I have a few 2504s on the bench and they have 3802s on them.  it is almost as if the 3802 has been on a 9800, the AP won't ever go back to a 2504.

I cannot seem to find anything posted where anyone has this scenario - where they are moving 3802s back down to a legacy controller.  

Anyone have a link, or possibly some advice?

Thanks!

[balaji.bandi]

We rented a building that already has a ceiling full of 9800s

Cat 9800 WLC not AP

 When we took occupancy, everyone thought the 3802s would join the 5520.  Nope.

check the matrix and if the right code that should work.  ( do you have any logs to understand from console for this scenarios) ?

Oddly, I have a few 2504s on the bench and they have 3802s on them.  it is almost as if the 3802 has been on a 9800, the AP won't ever go back to a 2504.

The given information - different models have different issue as i understand here.

To give right advise, the AP are on Cat 9800 controller you looking to join old AiOS controller ? or other way around.

Any case have you tried reset AP and use option 43 to join the right controller based on DHCP

if they are in same vlan both WLC in same VLAN, it join which ever first response to AP.

where they are moving 3802s back down to a legacy controller.  

Legacy controller AirOS - i take it , so you can do manually on the AP to move to Controller use IP or follow above mentioned procedure to join old Legacy controller?

make sure you check the compatibility matrix WLC and AP have right code.

Cat 9800 you have option select the AP and change the primary and secondary controller to OLD WLC IP address and save and reboot.

[denneht]

Yes, ceiling full of 3802s.

Code on 3504 and 2504 are the same.  That part I do not understand.

Previous tenant has the 3802s on a 9800.  We took over and we have a 5520.  APs won't join it.  Won't join a 2504, but will join a 3504.  I put everything on the SAME subnet.  They still will NOT join the 5520, or will they join the 2504.  I was hoping to have them join the 2504 and downgrade the code so maybe then they will join the 5520.

I configured the APs to join the 2504 when I put in the borrowed 9800.  They won't join it.  I put the 3504 on the same subnet, right next to the 2504, and they join the 3504.

I don't know what the problem could possibly be!

[balaji.bandi]

All of them running same code - AP and All the WLC ?

AirOS running 8.5.171.0

they join the 3504. - that should work for you, why do you need other WLC controllers ? (is the 3504 run AirOS running 8.5.171.0 ?)

I understand you can not do reset all the AP where they are located, but to understand pull one of the AP and post console logs possible ?

If not you need to Let AP join 3504 and change the config Controller config to other WLC and reload and check ?

as i asked before why do you need 3 WLC controllers different models in the network ? (any reason ?)

[Leo Laohoo]

Boot the AP and connect a console cable. 

Post the entire boot-up process.

[denneht]

9k_sw1#[*01/01/1970 00:00:02.8228] buginf() enabled.
[*01/01/1970 00:00:02.8335] Made it into bootsh: Mar 8 2023 06:10:15 T-824d9257bac45ad02762abfc76a2fdf79610cab5-g824d9257-aut
[*01/01/1970 00:00:11.0043] bootsh mini ramfs booted /bootpart/part1/ramfs_data_cisco.cpio.lzma

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.

This product contains some software licensed under the
"GNU Affero General Public License, version 3" provided
with ABSOLUTELY NO WARRANTY under the terms of
"GNU Affero General Public License, version 3", available here:
http://www.gnu.org/licenses/agpl-3.0.html.

[ OK ] Reached target Cisco File Systems (Pre).
[ OK ] Created slice -.slice.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Created slice system.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
Starting Cisco UBIFS reformat/mount...
[ OK ] Reached target Slices.
[ OK ] Reached target Timers.
Starting udev Kernel Device Manager...
[ OK ] Listening on Delayed Shutdown Socket.
[ OK ] Reached target Sockets.
[ OK ] Created slice system-sshd\x2dkeygen.slice.
Starting udev Coldplug all Devices...
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Cisco UBIFS reformat/mount.
Starting Cisco early mount...
[ OK ] Started Cisco early mount.
[ OK ] Reached target Local File Systems (Pre).
Starting Cisco platform file generation...
Starting Cisco fips check...
Starting Cisco system time setup...
Starting Cisco seed generation...
[ OK ] Started Cisco system time setup.
[ OK ] Started Cisco seed generation.
[ OK ] Started Cisco fips check.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Cisco platform file generation.
Starting Cisco btldr service...
[ OK ] Started Cisco btldr service.
[ OK ] Reached target Local File Systems.
Starting Cisco S10 boot service...
Starting Cisco pkg install service...
[*07/13/2019 23:59:59.0949] Last reload time: Mar 16 19:18:02 2024
[*03/16/2024 19:18:02.0012] Setting system time Sat Mar 16 19:18:02 UTC 2024
[*03/16/2024 19:18:03.1777] GCM-128 POST passed
[*03/16/2024 19:18:03.1778] GCM-256 POST passed
[*03/16/2024 19:18:04.8471] MGIG Bundeled version 201, Tarball version 201
[*03/16/2024 19:18:04.9110] Identified Ethernet mGig PHY: mv2010
[ OK ] Started Cisco system time saving.
Starting Cisco system time saving...
Starting Cisco act2 check...
[03/16/2024 19:18:10.0900] [sched_delayed] sched: RT throttling activated
[** ] (1 of 3) A start job is running for...10 boot service (12s / 1min 35s)[03/16/2024 19:18:11.2900] audit_printk_skb: 18 callbacks suppressed
[ OK ] Started Cisco act2 check.
[03/16/2024 19:18:12.4300] PCI: enabling device 0000:00:02.0 (0140 -> 0143)
[03/16/2024 19:18:12.5200] PCI: enabling device 0000:02:00.0 (0140 -> 0142)
[ OK ] Started Cisco pkg install service.
[*03/16/2024 19:18:07.1949]
[*03/16/2024 19:18:07.1949]
[*03/16/2024 19:18:07.1949]
[*03/16/2024 19:18:07.1949] Authenticating ACT2 ID:AP3800
[*03/16/2024 19:18:07.1949] Authenticating SN:FOC232744PZ
[*03/16/2024 19:18:07.1952]
[*03/16/2024 19:18:07.1952] (ACT2Boot) Hardware is Cisco (c) authentic
[*03/16/2024 19:18:07.1952]
[*03/16/2024 19:18:07.2007] Seeding /dev/urandom from ACT2
[*03/16/2024 19:18:07.9024] Reading ACT2 SUDI certificates
[*03/16/2024 19:18:11.6855] Active version: 17.9.3.50
[*03/16/2024 19:18:11.6949] Backup version: 8.5.182.7
[*03/16/2024 19:18:12.1970] device wired0 entered promiscuous mode
[*03/16/2024 19:18:12.6056] wifi0: Initializing TX ring
[*03/16/2024 19:18:12.6142] wifi0: prepare firmware downloading
[*03/16/2024 19:18:13.4466] wifi0: Firmware downloading
[*03/16/2024 19:18:14.6767] 0;0;0;0;[03/16/2024 19:18:18.8600] PCI: enabling device 0000:00:03.0 (0140 -> 0143)
[03/16/2024 19:18:18.9500] PCI: enabling device 0000:03:00.0 (0140 -> 0142)
[ *** ] A start job is running for Cisco S10 boot service (26s / 1min 35s)[03/16/2024 19:18:25.6000] audit_printk_skb: 42 callbacks suppressed
[ OK ] Started Cisco S10 boot service.
Starting Cisco nolan service...
Starting Cisco watchdog...
<30>systemd[1]: Started Cisco pkg install service.
[*03/16/2024 19:18:16.7167] 0;0;0;0;
[*03/16/2024 19:18:18.4407] Firmware download complete
[*03/16/2024 19:18:18.6347] wifi0: Getting HW specs. Retrying for 3
[*03/16/2024 19:18:18.6350] Mac_Init
[*03/16/2024 19:18:18.6354] Preparing to set HW specs
[*03/16/2024 19:18:18.6356] FIPS enc aes-ccmp Verified
[*03/16/2024 19:18:18.6357] FIPS dec aes-ccmp Verified
[*03/16/2024 19:18:18.6359] FIPS enc aes-ccmp-256 Verified
[*03/16/2024 19:18:18.6360] FIPS dec aes-ccmp-256 Verified
[*03/16/2024 19:18:18.6361] FIPS enc aes-gcmp Verified
[*03/16/2024 19:18:18.6362] FIPS dec aes-gcmp Verified
[*03/16/2024 19:18:18.6363] FIPS enc aes-gcmp-256 Verified
[*03/16/2024 19:18:18.6364] FIPS dec aes-gcmp-256 Verified
[*03/16/2024 19:18:19.0333] wifi1: Initializing TX ring
[*03/16/2024 19:18:19.0413] wifi1: prepare firmware downloading
[*03/16/2024 19:18:19.8729] wifi1: Firmware downloading
[*03/16/2024 19:18:21.0987] 0;0;0;0;0;0;0;
[*03/16/2024 19:18:24.3047] Firmware download complete
[*03/16/2024 19:18:24.5047] wifi1: Getting HW specs. Retrying for 3
[*03/16/2024 19:18:24.5050] Mac_Init
[*03/16/2024 19:18:24.5054] Preparing to set HW specs
[*03/16/2024 19:18:24.5056] FIPS enc aes-ccmp Verified
[*03/16/2024 19:18:24.5057] FIPS dec aes-ccmp Verified
[*03/16/2024 19:18:24.5058] FIPS enc aes-ccmp-256 Verified
[*03/16/2024 19:18:24.5059] FIPS dec aes-ccmp-256 Verified
[*03/16/2024 19:18:24.5060] FIPS enc aes-gcmp Verified
[*03/16/2024 19:18:24.5061] FIPS dec aes-gcmp Verified
[*03/16/2024 19:18:24.5063] FIPS enc aes-gcmp-256 Verified
[*03/16/2024 19:18:24.5064] FIPS dec aes-gcmp-256 Verified
[*03/16/2024 19:18:25.6126] Last reload reason : 0: unknown
Starting Cisco nss service...
[*03/16/2024 19:18:28.0076] Initializing NSS Firmware
[ OK ] Started Cisco nolan service.
[ OK ] Started Cisco watchdog.
Starting Cisco nolan USB service...
[ OK ] Started Cisco nolan USB service.
[ OK ] Started Cisco pre-PoE negotiation.
Starting Cisco pre-PoE negotiation...
[ OK ] Started Cisco nss service.
Starting Cisco Kclick...
Starting Cisco S15platform...
[03/16/2024 19:18:31.5600] Disabling lock debugging due to kernel taint
[ OK ] Started Cisco S15platform.
[ OK ] Started Cisco Kclick.
Starting Cisco Sku service...
[*03/16/2024 19:18:31.8844] NTKM - ntkm_init - Nitro KM loaded
[*03/16/2024 19:18:34.8144] SKU to radio FW
[*03/16/2024 19:18:34.8566] wifi2 no private ioctls.
[*03/16/2024 19:18:34.8567]
Starting Cisco certificate create service...
Starting Cisco ME service...
Starting Cisco sysctl service...
Starting Cisco Kclick...
[ OK ] Started Cisco Sku service.
[ OK ] Started Cisco ME service.
[ OK ] Started Cisco sysctl service.
[ OK ] Started Cisco certificate create service.
[*03/16/2024 19:18:35.7308] Create symlink /dev/mic_cert result 0
[*03/16/2024 19:18:35.7308] Loading certificates from storage...
[*03/16/2024 19:18:35.7703] barbados /tmp/SC4_1dbm.txt
Starting Cisco certtime service...
[ OK ] Started Tam server.
Starting Tam server...
Starting Cisco Tam service...
[ OK ] Started Cisco Tam service.
[ OK ] Started Cisco Kclick.
Starting Cisco syslog service...
Starting Cisco S16platfomm...
Starting rsyslog client...
[ OK ] Started Cisco syslog service.
[ OK ] Started Cisco S16platfomm.
[ OK ] Started rsyslog client.
Starting Cisco synclogd...
[ OK ] Started Cisco synclogd.
[ OK ] Started Cisco certtime service.
[ OK ] Reached target System Initialization.
[ OK ] Reached target Paths.
[ OK ] Reached target Basic System.
Starting RSYNC User Key Generation...
[ OK ] Started Serial Getty on ttyS0.
Starting Serial Getty on ttyS0...
[*03/16/2024 19:18:41.5347]
[*03/16/2024 19:18:41.5347] Click sched monitor: schedulers = 1
[*03/16/2024 19:19:09.0821] starting tam services using ACT2...
[*03/16/2024 19:19:09.0821]
[*03/16/2024 19:19:09.0821] TAM init done
[ OK ] Reached target Login Prompts.
Starting Security Auditing Service...
Starting AP Trace daemon...
[ OK ] Started System Monitor service.
Starting System Monitor service...
Starting Fast CGI daemon...
Starting Cisco printkd...
Starting Cisco brain service...
Starting Clean Air daemon...
[ OK ] Started NTP_PROC daemon.
Starting NTP_PROC daemon...
Starting Cisco klogd...
Starting Marvell Forwarding daemon...
Starting Cisco led service...
Starting WCPD process...
Starting Cisco kexec...
Starting Cisco rtd service...
Starting Cisco image/firmware updater service...
[*03/16/2024 19:19:11.1120]
[*03/16/2024 19:19:11.1120] [3/16/2024 19:20:12] updt_util: PHY firmware is up to date
Starting Hostapd process...
Starting capwapd...
[ OK ] Started Cisco printkd.
[ OK ] Started Cisco klogd.
[ OK ] Started Cisco kexec.
[ OK ] Started Cisco image/firmware updater service.
[ OK ] Started Cisco led service.
Starting ntp file watcher...
[*03/16/2024 19:19:11.8854] No valid NTP source
[*03/16/2024 19:19:11.8854] No valid ntp server info file. Stop NTP!
[ OK ] Started AP Trace daemon.
[ OK ] Started Fast CGI daemon.
[ OK ] Started Cisco rtd service.
[ OK ] Started ntp file watcher.
[ OK ] Started Hostapd process.
[*03/16/2024 19:19:12.3582] hostapd:Hostapd: DCDS not init cloud=0 webauth=255 255 init=0
[*03/16/2024 19:19:12.3582]
Starting ntp watcher...
[ OK ] Started ntp watcher.
[ OK ] Started Cisco brain service.
[03/16/2024 19:19:13.9200] wired0 emac 0: link up
[03/16/2024 19:19:13.9800] wired0: link up

User Access Verification
Username: [03/16/2024 19:19:23.9800] wired0 emac 0: link up
[03/16/2024 19:19:24.0400] wired0: link up
[*03/16/2024 19:19:24.0925] chatter: Device wired0 notify up link UP
[*03/16/2024 19:19:24.0928] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:19:24.7487] ip6_port srcr2, ip6local ::, ip6 ::, plen 0, gw6 ::, gw6_mac 00:00:00:00:00:00, mtu 1500, vid 0, mode6 2(slaac)
[*03/16/2024 19:19:25.3158] pid 8489's current affinity mask: 3
[*03/16/2024 19:19:25.3158] pid 8489's new affinity mask: 1
[*03/16/2024 19:19:26.0901] chpasswd: password for user changed
[*03/16/2024 19:19:26.2071] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] opened systemd socket successfully "
[*03/16/2024 19:19:26.2072] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] gRPC systemd sleep time: 30m0s"
[*03/16/2024 19:19:26.2073] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring grpccolinfo mutex lock"
[*03/16/2024 19:19:26.2073] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released grpccolinfo mutex lock. Time (ns) = 1160"
[*03/16/2024 19:19:26.2074] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring cci pmux lock"
[*03/16/2024 19:19:26.2074] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released cci pmux lock. Time (ns) = 1280"
[*03/16/2024 19:19:26.2074] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring pktstats mutex lock"
[*03/16/2024 19:19:26.2075] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released pktstats mutex lock. Time (ns) = 7240"
[*03/16/2024 19:19:26.2075] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring statscounter smux lock"
[*03/16/2024 19:19:26.2076] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released statscounter smux lock. Time (ns) = 1160"
[*03/16/2024 19:19:26.2076] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring ci pmux lock"
[*03/16/2024 19:19:26.2076] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released ci pmux lock. Time (ns) = 1160"
[*03/16/2024 19:19:26.2076] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring wlan delta lock"
[*03/16/2024 19:19:26.2077] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released wlan delta lock. Time (ns) = 1120"
[*03/16/2024 19:19:26.2077] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring radio delta lock"
[*03/16/2024 19:19:26.2077] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released radio delta lock. Time (ns) = 1040"
[*03/16/2024 19:19:26.2078] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring clients stats db lock"
[*03/16/2024 19:19:26.2078] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released clients stats db lock. Time (ns) = 1120"
[*03/16/2024 19:19:26.2078] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring ap stats lock"
[*03/16/2024 19:19:26.2079] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released ap stats lock. Time (ns) = 1160"
[*03/16/2024 19:19:26.2079] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Acquiring client_stats cmux lock"
[*03/16/2024 19:19:26.2079] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Released client_stats cmux lock. Time (ns) = 1080"
[*03/16/2024 19:19:26.2080] time="2024-03-16T19:19:26Z" level=info msg="[WATCHDOG] Going to sleep for 29m59.99928228s"
[*03/16/2024 19:19:26.4139] device aptrace0 entered promiscuous mode
[*03/16/2024 19:19:26.5318] USB Device Disconnected from the AP
[*03/16/2024 19:19:27.7779] DOT11_TXP[0]:Domain configured: 41 class:B
[*03/16/2024 19:19:28.0260] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:28.0419] DOT11_TXP[0]:Domain configured: 41 class:B
[*03/16/2024 19:19:28.2907] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:28.2931] DOT11_TXP[0]:Domain configured: 0 class:A
[*03/16/2024 19:19:28.3617] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:28.3637] DOT11_TXP[0]:Domain configured: 0 class:A
[*03/16/2024 19:19:28.4217] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:28.4354] DOT11_TXP[0]:Domain configured: 41 class:B
[*03/16/2024 19:19:28.6970] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:29.2081] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver Setting the radio mode to monitor from local
[*03/16/2024 19:19:29.2082] **Alert: Trying to push different mode monitor other than current radio mode local
[*03/16/2024 19:19:29.2146] **Alert: Initial Fw mode hostap Fw mode after cmdset monitor
[*03/16/2024 19:19:29.4953] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver Resetting the radio mode to local from monitor.
[*03/16/2024 19:19:29.5013] **Alert: Initial Fw mode monitor Fw mode after cmdset hostap
[*03/16/2024 19:19:29.5216] DOT11_DRV[1]: Stopped Radio 1
[*03/16/2024 19:19:29.5499] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:30.1154] DOT11_DRV[0]: wcp/RadDrv0 :: Dot11BaseDriver Setting the radio mode to monitor from local
[*03/16/2024 19:19:30.1155] **Alert: Trying to push different mode monitor other than current radio mode local
[*03/16/2024 19:19:30.1215] **Alert: Initial Fw mode hostap Fw mode after cmdset monitor
[*03/16/2024 19:19:30.4055] DOT11_DRV[0]: wcp/RadDrv0 :: Dot11BaseDriver Resetting the radio mode to local from monitor.
[*03/16/2024 19:19:30.4115] **Alert: Initial Fw mode monitor Fw mode after cmdset hostap
[*03/16/2024 19:19:30.4319] DOT11_DRV[0]: Stopped Radio 0
[*03/16/2024 19:19:30.4553] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 6
[*03/16/2024 19:19:30.9522] 00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6920 (rev 08) (prog-if 00 [Normal decode])
[*03/16/2024 19:19:30.9522] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:30.9522] Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:30.9522] Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
[*03/16/2024 19:19:30.9522] I/O behind bridge: 0000f000-00000fff
[*03/16/2024 19:19:30.9522] Memory behind bridge: fff00000-000fffff
[*03/16/2024 19:19:30.9522] Prefetchable memory behind bridge: 00000000-000fffff
[*03/16/2024 19:19:30.9522] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[*03/16/2024 19:19:30.9522] BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
[*03/16/2024 19:19:30.9523] PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
[*03/16/2024 19:19:30.9523]
[*03/16/2024 19:19:30.9523] 00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6920 (rev 08) (prog-if 00 [Normal decode])
[*03/16/2024 19:19:30.9523] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:30.9523] Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:30.9523] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:30.9523] Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
[*03/16/2024 19:19:30.9523] I/O behind bridge: 0000f000-00000fff
[*03/16/2024 19:19:30.9523] Memory behind bridge: f8000000-f82fffff
[*03/16/2024 19:19:30.9523] Prefetchable memory behind bridge: 00000000-000fffff
[*03/16/2024 19:19:30.9523] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[*03/16/2024 19:19:30.9523] BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
[*03/16/2024 19:19:30.9523] PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
[*03/16/2024 19:19:30.9523]
[*03/16/2024 19:19:30.9523] 00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6920 (rev 08) (prog-if 00 [Normal decode])
[*03/16/2024 19:19:30.9523] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:30.9523] Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:30.9523] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:30.9523] Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
[*03/16/2024 19:19:30.9524] I/O behind bridge: 0000f000-00000fff
[*03/16/2024 19:19:30.9524] Memory behind bridge: f8400000-f86fffff
[*03/16/2024 19:19:30.9524] Prefetchable memory behind bridge: 00000000-000fffff
[*03/16/2024 19:19:30.9524] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[*03/16/2024 19:19:30.9524] BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
[*03/16/2024 19:19:30.9524] PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
[*03/16/2024 19:19:30.9524]
[*03/16/2024 19:19:30.9524] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. Device 2b40
[*03/16/2024 19:19:30.9524] Subsystem: Marvell Technology Group Ltd. Device 0000
[*03/16/2024 19:19:30.9524] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:30.9524] Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:30.9524] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:30.9524] Interrupt: pin A routed to IRQ 65
[*03/16/2024 19:19:30.9524] Region 0: Memory at f8000000 (64-bit, prefetchable) [size=2M]
[*03/16/2024 19:19:30.9524] Region 2: Memory at f8200000 (64-bit, prefetchable) [size=1M]
[*03/16/2024 19:19:30.9524] Capabilities: [40] Power Management version 3
[*03/16/2024 19:19:30.9524] Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold+)
[*03/16/2024 19:19:30.9524] Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
[*03/16/2024 19:19:30.9524] Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
[*03/16/2024 19:19:30.9524] Address: 0000000000000000 Data: 0000
[*03/16/2024 19:19:30.9524] Masking: 00000000 Pending: 00000000
[*03/16/2024 19:19:30.9525] Capabilities: [70] Express (v2) Endpoint, MSI 00
[*03/16/2024 19:19:30.9525] DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
[*03/16/2024 19:19:30.9525] ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
[*03/16/2024 19:19:30.9525] DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
[*03/16/2024 19:19:30.9525] RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
[*03/16/2024 19:19:30.9525] MaxPayload 128 bytes, MaxReadReq 512 bytes
[*03/16/2024 19:19:30.9525] DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
[*03/16/2024 19:19:30.9525] LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 unlimited
[*03/16/2024 19:19:30.9525] ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
[*03/16/2024 19:19:30.9525] LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
[*03/16/2024 19:19:30.9525] ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
[*03/16/2024 19:19:30.9525] LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
[*03/16/2024 19:19:30.9525] DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported
[*03/16/2024 19:19:30.9525] DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
[*03/16/2024 19:19:30.9525] LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
[*03/16/2024 19:19:30.9525] Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
[*03/16/2024 19:19:30.9533] Compliance De-emphasis: -6dB
[*03/16/2024 19:19:30.9533] LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
[*03/16/2024 19:19:30.9533] EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
[*03/16/2024 19:19:30.9533] Capabilities: [b0] MSI-X: Enable- Count=32 Masked-
[*03/16/2024 19:19:30.9533] Vector table: BAR=2 offset=00001000
[*03/16/2024 19:19:30.9533] PBA: BAR=2 offset=00001800
[*03/16/2024 19:19:30.9533] Capabilities: [100 v2] Advanced Error Reporting
[*03/16/2024 19:19:30.9534] UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:30.9534] UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:30.9534] UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:30.9534] CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
[*03/16/2024 19:19:30.9534] CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
[*03/16/2024 19:19:30.9534] AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
[*03/16/2024 19:19:30.9534] Capabilities: [140 v1] Device Serial Number 00-00-00-00-00-00-00-00
[*03/16/2024 19:19:30.9534] Capabilities: [150 v1] Power Budgeting <?>
[*03/16/2024 19:19:30.9534] Capabilities: [160 v1] Latency Tolerance Reporting
[*03/16/2024 19:19:30.9534] Max snoop latency: 0ns
[*03/16/2024 19:19:30.9534] Max no snoop latency: 0ns
[*03/16/2024 19:19:30.9534] Kernel driver in use: wifi
[*03/16/2024 19:19:30.9534]
[*03/16/2024 19:19:30.9534] 03:00.0 Ethernet controller: Marvell Technology Group Ltd. Device 2b40
[*03/16/2024 19:19:30.9534] Subsystem: Marvell Technology Group Ltd. Device 0000
[*03/16/2024 19:19:30.9534] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:30.9534] Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:30.9534] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:30.9534] Interrupt: pin A routed to IRQ 102
[*03/16/2024 19:19:30.9534] Region 0: Memory at f8400000 (64-bit, prefetchable) [size=2M]
[*03/16/2024 19:19:30.9535] Region 2: Memory at f8600000 (64-bit, prefetchable) [size=1M]
[*03/16/2024 19:19:30.9535] Capabilities: [40] Power Management version 3
[*03/16/2024 19:19:30.9535] Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold+)
[*03/16/2024 19:19:30.9535] Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
[*03/16/2024 19:19:30.9535] Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
[*03/16/2024 19:19:30.9535] Address: 0000000000000000 Data: 0000
[*03/16/2024 19:19:30.9535] Masking: 00000000 Pending: 00000000
[*03/16/2024 19:19:30.9535] Capabilities: [70] Express (v2) Endpoint, MSI 00
[*03/16/2024 19:19:30.9535] DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
[*03/16/2024 19:19:30.9535] ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
[*03/16/2024 19:19:30.9535] DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
[*03/16/2024 19:19:30.9535] RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
[*03/16/2024 19:19:30.9535] MaxPayload 128 bytes, MaxReadReq 512 bytes
[*03/16/2024 19:19:30.9535] DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
[*03/16/2024 19:19:30.9535] LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 unlimited
[*03/16/2024 19:19:30.9535] ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
[*03/16/2024 19:19:30.9535] LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
[*03/16/2024 19:19:30.9535] ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
[*03/16/2024 19:19:30.9535] LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
[*03/16/2024 19:19:30.9535] DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported
[*03/16/2024 19:19:30.9535] DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
[*03/16/2024 19:19:30.9536] LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
[*03/16/2024 19:19:30.9536] Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
[*03/16/2024 19:19:30.9536] Compliance De-emphasis: -6dB
[*03/16/2024 19:19:30.9536] LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
[*03/16/2024 19:19:30.9536] EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
[*03/16/2024 19:19:30.9536] Capabilities: [b0] MSI-X: Enable- Count=32 Masked-
[*03/16/2024 19:19:30.9536] Vector table: BAR=2 offset=00001000
[*03/16/2024 19:19:30.9536] PBA: BAR=2 offset=00001800
[*03/16/2024 19:19:30.9536] Capabilities: [100 v2] Advanced Error Reporting
[*03/16/2024 19:19:30.9536] UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:30.9536] UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:30.9536] UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:30.9536] CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
[*03/16/2024 19:19:30.9536] CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
[*03/16/2024 19:19:30.9536] AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
[*03/16/2024 19:19:30.9536] Capabilities: [140 v1] Device Serial Number 00-00-00-00-00-00-00-00
[*03/16/2024 19:19:30.9536] Capabilities: [150 v1] Power Budgeting <?>
[*03/16/2024 19:19:30.9536] Capabilities: [160 v1] Latency Tolerance Reporting
[*03/16/2024 19:19:30.9536] Max snoop latency: 0ns
[*03/16/2024 19:19:30.9537] Max no snoop latency: 0ns
[*03/16/2024 19:19:30.9540] Kernel driver in use: wifi
[*03/16/2024 19:19:30.9540]
[*03/16/2024 19:19:30.9633] wifi0 Link encap:Ethernet HWaddr 68:3B:78:B0:52:A0
[*03/16/2024 19:19:30.9633] BROADCAST MULTICAST MTU:1500 Metric:1
[*03/16/2024 19:19:30.9633] RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[*03/16/2024 19:19:30.9633] TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[*03/16/2024 19:19:30.9633] collisions:0 txqueuelen:1000
[*03/16/2024 19:19:30.9633] RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[*03/16/2024 19:19:30.9633] Interrupt:65 Memory:f8000000-f8200000
[*03/16/2024 19:19:30.9633]
[*03/16/2024 19:19:30.9722] wifi1 Link encap:Ethernet HWaddr 68:3B:78:B0:52:A0
[*03/16/2024 19:19:30.9722] BROADCAST MULTICAST MTU:1500 Metric:1
[*03/16/2024 19:19:30.9722] RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[*03/16/2024 19:19:30.9722] TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[*03/16/2024 19:19:30.9722] collisions:0 txqueuelen:1000
[*03/16/2024 19:19:30.9722] RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[*03/16/2024 19:19:30.9722] Interrupt:102 Memory:f8400000-f8600000
[*03/16/2024 19:19:30.9722]
[*03/16/2024 19:19:30.9725] DOT11_DRV[2]: wcp/RadDrv2 :: Dot11BaseDriver get_radio_if_index ioctl SIOCGIFINDEX failed for wifi2 error -1
[*03/16/2024 19:19:30.9725] populate_if_index_table: radio index -1 for radio 2
[*03/16/2024 19:19:32.1468] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:32.8828] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:33.0787] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:33.9525] bftype is 6
[*03/16/2024 19:19:33.9757] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:34.6298] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:35.0578] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:35.6103] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:36.3544] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:36.3721] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:37.4111] bftype is 6
[*03/16/2024 19:19:37.4342] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:38.2684] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:39.0737] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:20:17.9908] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:20:19.5433] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:20:20.3615] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:20:32.4650] chatter: Device wired0 notify down link UP
[*03/16/2024 19:20:32.5009] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:20:34.5200] wired0 emac 0: link up
[03/16/2024 19:20:34.5700] wired0: link up
[*03/16/2024 19:20:34.6274] chatter: Device wired0 notify up link UP
[*03/16/2024 19:20:34.6275] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:20:49.6673] chatter: Device wired0 notify down link UP
[*03/16/2024 19:20:49.7033] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:20:51.7200] wired0 emac 0: link up
[03/16/2024 19:20:51.7700] wired0: link up
[*03/16/2024 19:20:51.8292] chatter: Device wired0 notify up link UP
[*03/16/2024 19:20:51.8296] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:06.8670] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:06.9029] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:21:08.9200] wired0 emac 0: link up
[03/16/2024 19:21:08.9700] wired0: link up
[*03/16/2024 19:21:09.0287] chatter: Device wired0 notify up link UP
[*03/16/2024 19:21:09.0294] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:24.0669] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:24.1029] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:21:26.1200] wired0 emac 0: link up
[03/16/2024 19:21:26.1700] wired0: link up
[*03/16/2024 19:21:26.2287] chatter: Device wired0 notify up link UP
[*03/16/2024 19:21:26.2288] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:41.2670] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:41.3036] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:21:43.3200] wired0 emac 0: link up
[03/16/2024 19:21:43.3800] wired0: link up
[*03/16/2024 19:21:43.4296] chatter: Device wired0 notify up link UP
[*03/16/2024 19:21:43.4296] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:58.4696] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:58.5056] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:22:00.5200] wired0 emac 0: link up
[03/16/2024 19:22:00.5800] wired0: link up
[*03/16/2024 19:22:00.6314] chatter: Device wired0 notify up link UP
[*03/16/2024 19:22:00.6318] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:22:15.6707] chatter: Device wired0 notify down link UP
[*03/16/2024 19:22:15.7071] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:22:17.7200] wired0 emac 0: link up
[03/16/2024 19:22:17.7800] wired0: link up
[*03/16/2024 19:22:17.8327] chatter: Device wired0 notify up link UP
[*03/16/2024 19:22:17.8328] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:22:32.8712] chatter: Device wired0 notify down link UP
[*03/16/2024 19:22:32.9077] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:22:34.9300] wired0 emac 0: link up
[03/16/2024 19:22:34.9800] wired0: link up
[*03/16/2024 19:22:35.0336] chatter: Device wired0 notify up link UP
[*03/16/2024 19:22:35.0336] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:22:50.0731] chatter: Device wired0 notify down link UP
[*03/16/2024 19:22:50.1095] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:22:52.1300] wired0 emac 0: link up
[03/16/2024 19:22:52.1800] wired0: link up
[*03/16/2024 19:22:52.2351] chatter: Device wired0 notify up link UP
[*03/16/2024 19:22:52.2356] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:23:07.2730] chatter: Device wired0 notify down link UP
[*03/16/2024 19:23:07.3090] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:23:09.3300] wired0 emac 0: link up
[03/16/2024 19:23:09.3800] wired0: link up
[*03/16/2024 19:23:09.4347] chatter: Device wired0 notify up link UP
[*03/16/2024 19:23:09.4348] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:23:24.4734] chatter: Device wired0 notify down link UP
[*03/16/2024 19:23:24.5094] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:23:26.5300] wired0 emac 0: link up
[03/16/2024 19:23:26.5800] wired0: link up
[*03/16/2024 19:23:26.6352] chatter: Device wired0 notify up link UP
[*03/16/2024 19:23:26.6353] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:23:41.6770] chatter: Device wired0 notify down link UP
[*03/16/2024 19:23:41.7133] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:23:43.7300] wired0 emac 0: link up
[03/16/2024 19:23:43.7800] wired0: link up
[*03/16/2024 19:23:43.8391] chatter: Device wired0 notify up link UP
[*03/16/2024 19:23:43.8392] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:23:58.8775] chatter: Device wired0 notify down link UP
[*03/16/2024 19:23:58.9138] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:24:00.9300] wired0 emac 0: link up
[03/16/2024 19:24:00.9900] wired0: link up
[*03/16/2024 19:24:01.0394] chatter: Device wired0 notify up link UP
[*03/16/2024 19:24:01.0399] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:24:16.0809] chatter: Device wired0 notify down link UP
[*03/16/2024 19:24:16.1174] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:24:18.1400] wired0 emac 0: link up
[03/16/2024 19:24:18.1900] wired0: link up
[*03/16/2024 19:24:18.2429] chatter: Device wired0 notify up link UP
[*03/16/2024 19:24:18.2434] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:24:33.2815] chatter: Device wired0 notify down link UP
[*03/16/2024 19:24:33.3178] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:24:35.3400] wired0 emac 0: link up
[03/16/2024 19:24:35.4000] wired0: link up
[*03/16/2024 19:24:35.4484] chatter: Device wired0 notify up link UP
[*03/16/2024 19:24:35.4489] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:24:50.4866] chatter: Device wired0 notify down link UP
[*03/16/2024 19:24:50.5255] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:24:52.5400] wired0 emac 0: link up
[03/16/2024 19:24:52.6000] wired0: link up
[*03/16/2024 19:24:52.6533] chatter: Device wired0 notify up link UP
[*03/16/2024 19:24:52.6538] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:25:07.6934] chatter: Device wired0 notify down link UP
[*03/16/2024 19:25:07.7298] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:25:09.7500] wired0 emac 0: link up
[03/16/2024 19:25:09.8000] wired0: link up
[*03/16/2024 19:25:09.8557] chatter: Device wired0 notify up link UP
[*03/16/2024 19:25:09.8559] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:25:24.8935] chatter: Device wired0 notify down link UP
[*03/16/2024 19:25:24.9298] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:25:26.9500] wired0 emac 0: link up
[03/16/2024 19:25:27.0000] wired0: link up
[*03/16/2024 19:25:27.0560] chatter: Device wired0 notify up link UP
[*03/16/2024 19:25:27.0564] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:25:42.0931] chatter: Device wired0 notify down link UP
[*03/16/2024 19:25:42.1292] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:25:44.1500] wired0 emac 0: link up
[03/16/2024 19:25:44.2000] wired0: link up
[*03/16/2024 19:25:44.2552] chatter: Device wired0 notify up link UP
[*03/16/2024 19:25:44.2553] chatter: Device wired0 notify state change link UP

[denneht]

Done!  Do you see anything out of the ordinary?

[denneht]

I have two 2504s I am testing with.  One is running 8.5.171.0, and the other is running 8.5.182.7

The AP will not join either one of them.  These are all on the same subnet on the bench.  AP gets an IP address.

The AP will blink green->red, the off.  Then start all over again.  After a while, it will go solid green for a short time, then start the green->red blinking all over again.

[*03/16/2024 19:37:42.3755] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:37:44.3900] wired0 emac 0: link up
[03/16/2024 19:37:44.4500] wired0: link up
[*03/16/2024 19:37:44.5013] chatter: Device wired0 notify up link UP
[*03/16/2024 19:37:44.5014] chatter: Device wired0 notify state change link UP
▒
BootROM - 1.78
Booting from SPI flash, Secure mode
BootROM: RSA Public key verification PASSED
BootROM: CSK block signature verification PASSED
BootROM: Boot header signature verification PASSED
BootROM: Box ID verification PASSED
BootROM: JTAG is disabled

General initialization - Version: 1.0.0
Detected Device ID 6920
Master bootloder version 1.44
High speed PHY - Version: 2.0
BoardId = 0x25board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 1 | 0 | SGMII1 |
| 2 | 5 | PCIe1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 1: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 2: Link upgraded to Gen2 based on client cpabilities
High speed PHY - Ended Successfully
DDR4 Training Sequence - Ver TIP-0.23.(Sublib 0.8)0
DDR4 Training Sequence - Switching XBAR Window to FastPath Window
DDR4 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
BootROM: Boot image signature verification PASSED

____ _
/ ___|(_) ___ ___ ___
| | | |/ __| / __|/ _ \
| |___ | |\__ \| (__| (_) |
\____||_||___/ \___|\___/
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **

U-Boot 2013.01-g2ee3a18aa (Jun 03 2022 - 11:27:17) SDK version: 2015_T2.0p10

Board: Barbados-3KVE
SoC: MV88F6920 Rev A1
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1800 [MHz]
L2 @ 900 [MHz]
TClock @ 250 [MHz]
DDR4 @ 900 [MHz]
DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB

RST I2C0
NAND: ECC 4bits, 256 MiB
SF: Detected S25FL032P with page size 64 KiB, total 4 MiB
PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 2 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 2.0

Map: Code: 0x3fed8000:0x3ffae448
BSS: 0x3ffeff0c
Stack: 0x3f9c7f20
Heap: 0x3f9c8000:0x3fed8000
U-Boot Environment: 0x00100000:0x00110000 (SPI)

Board configuration:
| port | Interface | PHY address |
|--------|------------|--------------|
| egiga1 | SGMII | 0x01 |
| egiga2 | SGMII | In-Band |
Net: , egiga1, egiga2 [PRIME]
Hit ESC key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000010000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBIFS: mounted UBI device 0, volume 0, name "part1"
Loading file 'part1/part.bin' to addr 0x02000000 with size 6877237 (0x0068f035)...
Done
SF: Detected S25FL032P with page size 64 KiB, total 4 MiB

Checking image signing.
Image signing verification success, continue to run...
Loading Marvel PHY firmware...
Ethernet transceiver PHY firmware download started:
Downloading to PHY's RAM........................ 195552 of 195552 Bytes transferred. [Done]
Ethernet transceiver PHY firmware download succeeded.
Automatic Voltage setting value: 05
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Barbados Firmware Image
Created: 2023-03-08 6:18:24 UTC
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 6876229 Bytes = 6.6 MiB
Load Address: 00008000
Entry Point: 00008000
Contents:
Image 0: 4202864 Bytes = 4 MiB
Image 1: 2657210 Bytes = 2.5 MiB
Image 2: 16137 Bytes = 15.8 KiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 02000000 ...
## Flattened Device Tree from multi component Image at 02000000
Booting using the fdt at 0x0268ad7c
Loading Multi-File Image ... OK
OK
reserving fdt memory region: addr=0 size=4000
Loading Device Tree to 01ff9000, end 01ffff08 ... OK

Starting Device Tree update ('fdt_skip_update' = no)

Limit DDR size at 3GB due to power of 2 requirement of Address decoding
Updating device tree successful

Starting kernel ...

[01/01/1970 00:00:00.0000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
[01/01/1970 00:00:00.0000] Memory: 1025280K/1048576K available (5743K kernel code, 411K rwdata, 2480K rodata, 359K init, 496K bss, 23296K reserved, 0K highmem)
[01/01/1970 00:00:00.1200] CPU1: Booted secondary processor
[01/01/1970 00:00:01.5900] buginf tty flushing thread started, ttyport=bf0f3c00
[01/01/1970 00:00:01.7100] m25p80 spi1.0: found s25sl032p, expected n25q032
[*01/01/1970 00:00:02.8234] buginf() enabled.
[*01/01/1970 00:00:02.8341] Made it into bootsh: Mar 8 2023 06:10:15 T-824d9257bac45ad02762abfc76a2fdf79610cab5-g824d9257-aut
[*01/01/1970 00:00:11.0020] bootsh mini ramfs booted /bootpart/part1/ramfs_data_cisco.cpio.lzma

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.

This product contains some software licensed under the
"GNU Affero General Public License, version 3" provided
with ABSOLUTELY NO WARRANTY under the terms of
"GNU Affero General Public License, version 3", available here:
http://www.gnu.org/licenses/agpl-3.0.html.

[ OK ] Created slice -.slice.
[ OK ] Reached target Timers.
[ OK ] Created slice system.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
Starting Cisco UBIFS reformat/mount...
[ OK ] Reached target Slices.
[ OK ] Created slice system-sshd\x2dkeygen.slice.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Reached target Cisco File Systems (Pre).
[ OK ] Listening on Delayed Shutdown Socket.
[ OK ] Listening on udev Control Socket.
Starting udev Coldplug all Devices...
[ OK ] Reached target Sockets.
Starting udev Kernel Device Manager...
[ OK ] Started Cisco UBIFS reformat/mount.
[ OK ] Started udev Kernel Device Manager.
Starting Cisco early mount...
[ OK ] Started Cisco early mount.
[ OK ] Reached target Local File Systems (Pre).
Starting Cisco seed generation...
Starting Cisco fips check...
Starting Cisco platform file generation...
Starting Cisco system time setup...
[ OK ] Started Cisco seed generation.
[*07/13/2019 23:59:59.0931] Last reload time: Mar 16 19:18:02 2024
[*03/16/2024 19:18:02.0013] Setting system time Sat Mar 16 19:18:02 UTC 2024
[ OK ] Started Cisco system time setup.
[ OK ] Started Cisco fips check.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Cisco platform file generation.
Starting Cisco btldr service...
[ OK ] Started Cisco btldr service.
[ OK ] Reached target Local File Systems.
Starting Cisco S10 boot service...
Starting Cisco pkg install service...
[*03/16/2024 19:18:03.2255] GCM-128 POST passed
[*03/16/2024 19:18:03.2255] GCM-256 POST passed
Starting Cisco act2 check...
[*03/16/2024 19:18:04.7369] MGIG Bundeled version 201, Tarball version 201
[ OK ] Started Cisco system time saving.
[*03/16/2024 19:18:04.8759] Identified Ethernet mGig PHY: mv2010
Starting Cisco system time saving...
[03/16/2024 19:18:10.0700] [sched_delayed] sched: RT throttling activated
[ OK ] Started Cisco act2 check.
[03/16/2024 19:18:11.2300] audit_printk_skb: 18 callbacks suppressed
[03/16/2024 19:18:12.2900] PCI: enabling device 0000:00:02.0 (0140 -> 0143)
[03/16/2024 19:18:12.3700] PCI: enabling device 0000:02:00.0 (0140 -> 0142)
[ OK ] Started Cisco pkg install service.
[03/16/2024 19:18:18.7100] PCI: enabling device 0000:00:03.0 (0140 -> 0143)
[03/16/2024 19:18:18.7900] PCI: enabling device 0000:03:00.0 (0140 -> 0142)
[** ] A start job is running for Cisco S10 boot service (22s / 1min 35s)[*03/16/2024 19:18:07.3573]
[*03/16/2024 19:18:07.3573]
[*03/16/2024 19:18:07.3573]
[ *] A start job is running for Cisco S10 boot service (25s / 1min 35s)0;0;0;0;0;0;
[*03/16/2024 19:18:24.1504] Firmware download complete
[ ***] A start job is running for Cisco S10 boot service (26s / 1min [03/16/2024 19:18:25.4400] audit_printk_skb: 42 callbacks suppressed
35s)[*03/16/2024 19:18:24.3408] wifi1: Getting HW specs. Retrying for 3
[*03/16/2024 19:18:24.3411] Mac_Init
[*03/16/2024 19:18:24.3414] Preparing to set HW specs
[*03/16/2024 19:18:24.3417] FIPS enc aes-ccmp Verified
[*03/16/2024 19:18:24.3418] FIPS dec aes-ccmp Verified
[*03/16/2024 19:18:24.3419] FIPS enc aes-ccmp-256 Verified
[*03/16/2024 19:18:24.3420] FIPS dec aes-ccmp-256 Verified
[*03/16/2024 19:18:24.3421] FIPS enc aes-gcmp Verified
[*03/16/2024 19:18:24.3422] FIPS dec aes-gcmp Verified
[*03/16/2024 19:18:24.3424] FIPS enc aes-gcmp-256 Verified
[*03/16/2024 19:18:24.3425] FIPS dec aes-gcmp-256 Verified
[*03/16/2024 19:18:25.4482] Last reload reason : 0: unknown
[ OK ] Started Cisco S10 boot service.
Starting Cisco nolan service...
Starting Cisco watchdog...
Starting Cisco nss service...
[*03/16/2024 19:18:26.5139] Initializing NSS Firmware
[ OK ] Started Cisco nolan service.
[ OK ] Started Cisco watchdog.
Starting Cisco nolan USB service...
[ OK ] Started Cisco nolan USB service.
[ OK ] Started Cisco pre-PoE negotiation.
Starting Cisco pre-PoE negotiation...
[ OK ] Started Cisco nss service.
Starting Cisco Kclick...
Starting Cisco S15platform...
[03/16/2024 19:18:30.0700] Disabling lock debugging due to kernel taint
[ OK ] Started Cisco S15platform.
[ OK ] Started Cisco Kclick.
Starting Cisco Sku service...
[*03/16/2024 19:18:30.3853] NTKM - ntkm_init - Nitro KM loaded
[*03/16/2024 19:18:33.3105] SKU to radio FW
[*03/16/2024 19:18:33.3531] wifi2 no private ioctls.
[*03/16/2024 19:18:33.3531]
Starting Cisco sysctl service...
Starting Cisco ME service...
Starting Cisco certificate create service...
Starting Cisco Kclick...
[ OK ] Started Cisco Sku service.
[ OK ] Started Cisco sysctl service.
[ OK ] Started Cisco ME service.
[ OK ] Started Cisco certificate create service.
[ OK ] Started Tam server.
Starting Tam server...
[*03/16/2024 19:18:34.3842] Create symlink /dev/mic_cert result 0
[*03/16/2024 19:18:34.3842] Loading certificates from storage...
[*03/16/2024 19:18:34.4317] barbados /tmp/SC4_1dbm.txt
Starting Cisco Tam service...
Starting Cisco certtime service...
[ OK ] Started Cisco Tam service.
[ OK ] Started Cisco Kclick.
Starting Cisco S16platfomm...
Starting Cisco syslog service...
Starting rsyslog client...
[ OK ] Started Cisco S16platfomm.
[ OK ] Started Cisco syslog service.
[ OK ] Started rsyslog client.
Starting Cisco synclogd...
[ OK ] Started Cisco synclogd.
[ OK ] Started Cisco certtime service.
[ OK ] Reached target System Initialization.
[ OK ] Reached target Paths.
[ OK ] Reached target Basic System.
Starting Cisco kexec...
Starting Marvell Forwarding daemon...
[*03/16/2024 19:18:40.0308]
[*03/16/2024 19:18:40.0308] Click sched monitor: schedulers = 1
[*03/16/2024 19:19:07.7522] starting tam services using ACT2...
[*03/16/2024 19:19:07.7522]
[*03/16/2024 19:19:07.7522] TAM init done
Starting Hostapd process...
Starting Fast CGI daemon...
Starting Clean Air daemon...
Starting RSYNC User Key Generation...
Starting Cisco klogd...
Starting Security Auditing Service...
Starting Cisco brain service...
Starting capwapd...
[ OK ] Started Serial Getty on ttyS0.
Starting Serial Getty on ttyS0...
[ OK ] Reached target Login Prompts.
Starting AP Trace daemon...
[ OK ] Started System Monitor service.
Starting System Monitor service...
Starting Cisco rtd service...
Starting Cisco printkd...
Starting WCPD process...
[ OK ] Started NTP_PROC daemon.
Starting NTP_PROC daemon...
Starting Cisco image/firmware updater service...
[*03/16/2024 19:19:09.7906]
[*03/16/2024 19:19:09.7906] [3/16/2024 19:20:10] updt_util: PHY firmware is up to date
Starting Cisco led service...
[ OK ] Started Cisco kexec.
[ OK ] Started Cisco klogd.
[ OK ] Started Cisco printkd.
[ OK ] Started Cisco image/firmware updater service.
Starting ntp file watcher...
[*03/16/2024 19:19:10.6273] No valid NTP source
[*03/16/2024 19:19:10.6273] No valid ntp server inf[ OK ] Started Fast CGI daemon.
[ OK ] Started AP Trace daemon.
[ OK ] Started Cisco rtd service.
[ OK ] Started Cisco led service.
[ OK ] Started Hostapd process.
Starting ntp watcher...
[ OK ] Started ntp file watcher.
[ OK ] Started Cisco brain service.
[ OK ] Started ntp watcher.
[03/16/2024 19:19:12.5900] wired0 emac 0: link up
[03/16/2024 19:19:12.6500] wired0: link up

User Access Verification
Username: [03/16/2024 19:19:22.6900] wired0 emac 0: link up
[03/16/2024 19:19:22.7400] wired0: link up
[*03/16/2024 19:19:22.7958] chatter: Device wired0 notify up link UP
[*03/16/2024 19:19:22.7963] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:19:23.4612] ip6_port srcr2, ip6local ::, ip6 ::, plen 0, gw6 ::, gw6_mac 00:00:00:00:00:00, mtu 1500, vid 0, mode6 2(slaac)
[*03/16/2024 19:19:24.0514] pid 8503's current affinity mask: 3
[*03/16/2024 19:19:24.0514] pid 8503's new affinity mask: 1
[*03/16/2024 19:19:24.8251] chpasswd: password for user changed
[*03/16/2024 19:19:25.1709] device aptrace0 entered promiscuous mode
[*03/16/2024 19:19:26.4356] DOT11_TXP[0]:Domain configured: 41 class:B
[*03/16/2024 19:19:26.6804] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:26.6833] DOT11_TXP[0]:Domain configured: 41 class:B
[*03/16/2024 19:19:26.9316] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:26.9463] DOT11_TXP[2]:Domain configured: 41 class:B
[*03/16/2024 19:19:27.2062] DOT11_TXP[2]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:27.2089] DOT11_TXP[2]:Domain configured: 0 class:A
[*03/16/2024 19:19:27.2792] DOT11_TXP[2]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:27.2810] DOT11_TXP[0]:Domain configured: 0 class:A
[*03/16/2024 19:19:27.3409] DOT11_TXP[0]:Regdb file: /radio_fw/AP3802I_power_table_mapping.txt
[*03/16/2024 19:19:27.8395] DOT11_DRV[0]: wcp/RadDrv0 :: Dot11BaseDriver Setting the radio mode to monitor from local
[*03/16/2024 19:19:27.8395] **Alert: Trying to push different mode monitor other than current radio mode local
[*03/16/2024 19:19:27.8461] **Alert: Initial Fw mode hostap Fw mode after cmdset monitor
[*03/16/2024 19:19:28.1383] DOT11_DRV[0]: wcp/RadDrv0 :: Dot11BaseDriver Resetting the radio mode to local from monitor.
[*03/16/2024 19:19:28.1444] **Alert: Initial Fw mode monitor Fw mode after cmdset hostap
[*03/16/2024 19:19:28.1647] DOT11_DRV[0]: Stopped Radio 0
[*03/16/2024 19:19:28.1878] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 6
[*03/16/2024 19:19:28.6800] 00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6920 (rev 08) (prog-if 00 [Normal decode])
[*03/16/2024 19:19:28.6800] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:28.6800] Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:28.6800] Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
[*03/16/2024 19:19:28.6800] I/O behind bridge: 0000f000-00000fff
[*03/16/2024 19:19:28.6800] Memory behind bridge: fff00000-000fffff
[*03/16/2024 19:19:28.6801] Prefetchable memory behind bridge: 00000000-000fffff
[*03/16/2024 19:19:28.6801] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[*03/16/2024 19:19:28.6801] BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
[*03/16/2024 19:19:28.6801] PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
[*03/16/2024 19:19:28.6801]
[*03/16/2024 19:19:28.6801] 00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6920 (rev 08) (prog-if 00 [Normal decode])
[*03/16/2024 19:19:28.6801] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:28.6801] Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:28.6801] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:28.6801] Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
[*03/16/2024 19:19:28.6801] I/O behind bridge: 0000f000-00000fff
[*03/16/2024 19:19:28.6801] Memory behind bridge: f8000000-f82fffff
[*03/16/2024 19:19:28.6801] Prefetchable memory behind bridge: 00000000-000fffff
[*03/16/2024 19:19:28.6801] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[*03/16/2024 19:19:28.6801] BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
[*03/16/2024 19:19:28.6801] PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
[*03/16/2024 19:19:28.6801]
[*03/16/2024 19:19:28.6801] 00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6920 (rev 08) (prog-if 00 [Normal decode])
[*03/16/2024 19:19:28.6801] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:28.6802] Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:28.6802] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:28.6802] Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
[*03/16/2024 19:19:28.6802] I/O behind bridge: 0000f000-00000fff
[*03/16/2024 19:19:28.6802] Memory behind bridge: f8400000-f86fffff
[*03/16/2024 19:19:28.6802] Prefetchable memory behind bridge: 00000000-000fffff
[*03/16/2024 19:19:28.6802] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
[*03/16/2024 19:19:28.6802] BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
[*03/16/2024 19:19:28.6802] PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
[*03/16/2024 19:19:28.6802]
[*03/16/2024 19:19:28.6802] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. Device 2b40
[*03/16/2024 19:19:28.6802] Subsystem: Marvell Technology Group Ltd. Device 0000
[*03/16/2024 19:19:28.6802] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:28.6802] Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:28.6802] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:28.6802] Interrupt: pin A routed to IRQ 65
[*03/16/2024 19:19:28.6802] Region 0: Memory at f8000000 (64-bit, prefetchable) [size=2M]
[*03/16/2024 19:19:28.6802] Region 2: Memory at f8200000 (64-bit, prefetchable) [size=1M]
[*03/16/2024 19:19:28.6802] Capabilities: [40] Power Management version 3
[*03/16/2024 19:19:28.6802] Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold+)
[*03/16/2024 19:19:28.6803] Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
[*03/16/2024 19:19:28.6803] Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
[*03/16/2024 19:19:28.6803] Address: 0000000000000000 Data: 0000
[*03/16/2024 19:19:28.6803] Masking: 00000000 Pending: 00000000
[*03/16/2024 19:19:28.6803] Capabilities: [70] Express (v2) Endpoint, MSI 00
[*03/16/2024 19:19:28.6803] DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
[*03/16/2024 19:19:28.6803] ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
[*03/16/2024 19:19:28.6803] DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
[*03/16/2024 19:19:28.6803] RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
[*03/16/2024 19:19:28.6803] MaxPayload 128 bytes, MaxReadReq 512 bytes
[*03/16/2024 19:19:28.6803] DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
[*03/16/2024 19:19:28.6803] LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 unlimited
[*03/16/2024 19:19:28.6803] ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
[*03/16/2024 19:19:28.6803] LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
[*03/16/2024 19:19:28.6803] ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
[*03/16/2024 19:19:28.6803] LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
[*03/16/2024 19:19:28.6803] DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported
[*03/16/2024 19:19:28.6803] DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
[*03/16/2024 19:19:28.6803] LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
[*03/16/2024 19:19:28.6804] Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
[*03/16/2024 19:19:28.6812] Compliance De-emphasis: -6dB
[*03/16/2024 19:19:28.6812] LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
[*03/16/2024 19:19:28.6812] EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
[*03/16/2024 19:19:28.6812] Capabilities: [b0] MSI-X: Enable- Count=32 Masked-
[*03/16/2024 19:19:28.6812] Vector table: BAR=2 offset=00001000
[*03/16/2024 19:19:28.6812] PBA: BAR=2 offset=00001800
[*03/16/2024 19:19:28.6812] Capabilities: [100 v2] Advanced Error Reporting
[*03/16/2024 19:19:28.6812] UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:28.6812] UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:28.6812] UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:28.6812] CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
[*03/16/2024 19:19:28.6812] CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
[*03/16/2024 19:19:28.6812] AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
[*03/16/2024 19:19:28.6812] Capabilities: [140 v1] Device Serial Number 00-00-00-00-00-00-00-00
[*03/16/2024 19:19:28.6812] Capabilities: [150 v1] Power Budgeting <?>
[*03/16/2024 19:19:28.6812] Capabilities: [160 v1] Latency Tolerance Reporting
[*03/16/2024 19:19:28.6812] Max snoop latency: 0ns
[*03/16/2024 19:19:28.6812] Max no snoop latency: 0ns
[*03/16/2024 19:19:28.6812] Kernel driver in use: wifi
[*03/16/2024 19:19:28.6813]
[*03/16/2024 19:19:28.6813] 03:00.0 Ethernet controller: Marvell Technology Group Ltd. Device 2b40
[*03/16/2024 19:19:28.6813] Subsystem: Marvell Technology Group Ltd. Device 0000
[*03/16/2024 19:19:28.6813] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
[*03/16/2024 19:19:28.6813] Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
[*03/16/2024 19:19:28.6813] Latency: 0, Cache Line Size: 64 bytes
[*03/16/2024 19:19:28.6813] Interrupt: pin A routed to IRQ 102
[*03/16/2024 19:19:28.6813] Region 0: Memory at f8400000 (64-bit, prefetchable) [size=2M]
[*03/16/2024 19:19:28.6813] Region 2: Memory at f8600000 (64-bit, prefetchable) [size=1M]
[*03/16/2024 19:19:28.6813] Capabilities: [40] Power Management version 3
[*03/16/2024 19:19:28.6813] Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold+)
[*03/16/2024 19:19:28.6813] Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
[*03/16/2024 19:19:28.6813] Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
[*03/16/2024 19:19:28.6813] Address: 0000000000000000 Data: 0000
[*03/16/2024 19:19:28.6813] Masking: 00000000 Pending: 00000000
[*03/16/2024 19:19:28.6813] Capabilities: [70] Express (v2) Endpoint, MSI 00
[*03/16/2024 19:19:28.6813] DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
[*03/16/2024 19:19:28.6813] ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
[*03/16/2024 19:19:28.6813] DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
[*03/16/2024 19:19:28.6813] RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
[*03/16/2024 19:19:28.6813] MaxPayload 128 bytes, MaxReadReq 512 bytes
[*03/16/2024 19:19:28.6814] DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
[*03/16/2024 19:19:28.6814] LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 unlimited
[*03/16/2024 19:19:28.6814] ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
[*03/16/2024 19:19:28.6814] LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
[*03/16/2024 19:19:28.6814] ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
[*03/16/2024 19:19:28.6814] LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
[*03/16/2024 19:19:28.6814] DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported
[*03/16/2024 19:19:28.6814] DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
[*03/16/2024 19:19:28.6814] LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
[*03/16/2024 19:19:28.6814] Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
[*03/16/2024 19:19:28.6814] Compliance De-emphasis: -6dB
[*03/16/2024 19:19:28.6814] LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
[*03/16/2024 19:19:28.6814] EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
[*03/16/2024 19:19:28.6814] Capabilities: [b0] MSI-X: Enable- Count=32 Masked-
[*03/16/2024 19:19:28.6814] Vector table: BAR=2 offset=00001000
[*03/16/2024 19:19:28.6814] PBA: BAR=2 offset=00001800
[*03/16/2024 19:19:28.6814] Capabilities: [100 v2] Advanced Error Reporting
[*03/16/2024 19:19:28.6814] UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:28.6814] UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:28.6814] UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
[*03/16/2024 19:19:28.6815] CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
[*03/16/2024 19:19:28.6815] CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
[*03/16/2024 19:19:28.6815] AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
[*03/16/2024 19:19:28.6815] Capabilities: [140 v1] Device Serial Number 00-00-00-00-00-00-00-00
[*03/16/2024 19:19:28.6815] Capabilities: [150 v1] Power Budgeting <?>
[*03/16/2024 19:19:28.6815] Capabilities: [160 v1] Latency Tolerance Reporting
[*03/16/2024 19:19:28.6815] Max snoop latency: 0ns
[*03/16/2024 19:19:28.6815] Max no snoop latency: 0ns
[*03/16/2024 19:19:28.6818] Kernel driver in use: wifi
[*03/16/2024 19:19:28.6818]
[*03/16/2024 19:19:28.6899] wifi0 Link encap:Ethernet HWaddr 68:3B:78:B0:52:A0
[*03/16/2024 19:19:28.6899] BROADCAST MULTICAST MTU:1500 Metric:1
[*03/16/2024 19:19:28.6899] RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[*03/16/2024 19:19:28.6899] TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[*03/16/2024 19:19:28.6899] collisions:0 txqueuelen:1000
[*03/16/2024 19:19:28.6899] RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[*03/16/2024 19:19:28.6899] Interrupt:65 Memory:f8000000-f8200000
[*03/16/2024 19:19:28.6899]
[*03/16/2024 19:19:28.6987] wifi1 Link encap:Ethernet HWaddr 68:3B:78:B0:52:A0
[*03/16/2024 19:19:28.6988] BROADCAST MULTICAST MTU:1500 Metric:1
[*03/16/2024 19:19:28.6988] RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[*03/16/2024 19:19:28.6988] TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[*03/16/2024 19:19:28.6988] collisions:0 txqueuelen:1000
[*03/16/2024 19:19:28.6988] RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[*03/16/2024 19:19:28.6988] Interrupt:102 Memory:f8400000-f8600000
[*03/16/2024 19:19:28.6988]
[*03/16/2024 19:19:28.6991] DOT11_DRV[2]: wcp/RadDrv2 :: Dot11BaseDriver get_radio_if_index ioctl SIOCGIFINDEX failed for wifi2 error -1
[*03/16/2024 19:19:28.6991] populate_if_index_table: radio index -1 for radio 2
[*03/16/2024 19:19:28.8251] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver Setting the radio mode to monitor from local
[*03/16/2024 19:19:28.8252] **Alert: Trying to push different mode monitor other than current radio mode local
[*03/16/2024 19:19:28.8311] **Alert: Initial Fw mode hostap Fw mode after cmdset monitor
[*03/16/2024 19:19:29.1316] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver Resetting the radio mode to local from monitor.
[*03/16/2024 19:19:29.1377] **Alert: Initial Fw mode monitor Fw mode after cmdset hostap
[*03/16/2024 19:19:29.1581] DOT11_DRV[1]: Stopped Radio 1
[*03/16/2024 19:19:29.1814] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:30.1475] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:30.8739] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:31.0806] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:31.9455] bftype is 6
[*03/16/2024 19:19:31.9685] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:32.6331] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:33.0548] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:33.6080] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:34.3694] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:34.4024] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:35.4783] bftype is 6
[*03/16/2024 19:19:35.5015] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:36.3359] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:37.1449] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:38.1585] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 11
[*03/16/2024 19:19:39.6883] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:40.5140] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*03/16/2024 19:19:52.6085] chatter: Device wired0 notify down link UP
[*03/16/2024 19:19:52.6446] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:19:54.6700] wired0 emac 0: link up
[03/16/2024 19:19:54.7200] wired0: link up
[*03/16/2024 19:19:54.7705] chatter: Device wired0 notify up link UP
[*03/16/2024 19:19:54.7709] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:20:09.8075] chatter: Device wired0 notify down link UP
[*03/16/2024 19:20:09.8439] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:20:11.8600] wired0 emac 0: link up
[03/16/2024 19:20:11.9200] wired0: link up
[*03/16/2024 19:20:11.9696] chatter: Device wired0 notify up link UP
[*03/16/2024 19:20:11.9700] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:20:27.0101] chatter: Device wired0 notify down link UP
[*03/16/2024 19:20:27.0464] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:20:29.0700] wired0 emac 0: link up
[03/16/2024 19:20:29.1200] wired0: link up
[*03/16/2024 19:20:29.1722] chatter: Device wired0 notify up link UP
[*03/16/2024 19:20:29.1727] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:20:44.2123] chatter: Device wired0 notify down link UP
[*03/16/2024 19:20:44.2489] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:20:46.2700] wired0 emac 0: link up
[03/16/2024 19:20:46.3200] wired0: link up
[*03/16/2024 19:20:46.3747] chatter: Device wired0 notify up link UP
[*03/16/2024 19:20:46.3752] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:01.4131] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:01.4495] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:21:03.4700] wired0 emac 0: link up
[03/16/2024 19:21:03.5200] wired0: link up
[*03/16/2024 19:21:03.5751] chatter: Device wired0 notify up link UP
[*03/16/2024 19:21:03.5752] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:18.6136] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:18.6499] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:21:20.6700] wired0 emac 0: link up
[03/16/2024 19:21:20.7200] wired0: link up
[*03/16/2024 19:21:20.7755] chatter: Device wired0 notify up link UP
[*03/16/2024 19:21:20.7759] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:35.8167] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:35.8530] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:21:37.8700] wired0 emac 0: link up
[03/16/2024 19:21:37.9300] wired0: link up
[*03/16/2024 19:21:37.9791] chatter: Device wired0 notify up link UP
[*03/16/2024 19:21:37.9797] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:21:53.0183] chatter: Device wired0 notify down link UP
[*03/16/2024 19:21:53.0546] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:21:55.0800] wired0 emac 0: link up
[03/16/2024 19:21:55.1300] wired0: link up
[*03/16/2024 19:21:55.1802] chatter: Device wired0 notify up link UP
[*03/16/2024 19:21:55.1807] chatter: Device wired0 notify state change link UP
d1: *** sensord died (src/ki_taskwd.c:617/0x0) - slot 1 ***
d1: sensord: shutdown slot 1
[*03/16/2024 19:22:10.2196] chatter: Device wired0 notify down link UP
[*03/16/2024 19:22:10.2556] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:22:12.2800] wired0 emac 0: link up
[03/16/2024 19:22:12.3300] wired0: link up
[*03/16/2024 19:22:12.3813] chatter: Device wired0 notify up link UP
[*03/16/2024 19:22:12.3817] chatter: Device wired0 notify state change link UP
[*03/16/2024 19:22:27.4217] chatter: Device wired0 notify down link UP
[*03/16/2024 19:22:27.4577] chatter: Device wired0 notify down link DOWN
[03/16/2024 19:22:29.4800] wired0 emac 0: link up
[03/16/2024 19:22:29.5300] wired0: link up
[*03/16/2024 19:22:29.5834] chatter: Device wired0 notify up link UP
[*03/16/2024 19:22:29.5839] chatter: Device wired0 notify state change link UP

[denneht]

AP gets IP:

9k_sw1>sho ip dhcp bind
Bindings from all pools not associated with VRF:
IP address Client-ID/ Lease expiration Type State Interface
Hardware address/
User name
192.168.1.13 0108.4fa9.4b75.84 Mar 17 2024 02:02 AM Automatic Selecting Vlan1
9k_sw1>

9k_sw1#sh run int vlan1
Building configuration...

Current configuration : 87 bytes
!
interface Vlan1
description bench network
ip address 192.168.1.3 255.255.255.0
end

ip dhcp pool mgmt
network 192.168.1.0 255.255.255.0
default-router 192.168.1.254
dns-server 8.8.8.8

ip dhcp excluded-address 192.168.1.200 192.168.1.255
ip dhcp excluded-address 192.168.1.1 192.168.1.10

9k_sw1#sho vlan

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/1, Gi0/2, Gi0/3, Gi0/4
Gi0/5, Gi0/6, Gi0/7, Gi0/8
Gi0/9, Gi0/10, Gi0/11, Gi0/12
Gi0/26, Gi0/27, Gi0/28

Everything is on the same subnet.  The AP will simply not join either one.  But if I connect a 3504, it will.

[denneht]

AirOS running 8.5.171.0, IOS XE 17.9.3

[Leo Laohoo]

What is the Regulatory Domain of the AP?
What Country is configured on the 2504?
Factory-rest the AP and try again?

[denneht]

Everything US.  Just checked.  Just made sure everything was on same NTP.  All boxes on same subnet.  

Regarding factory resets.  The ones in the building are not only above the ceiling tiles, we don't exactly know where they are.  And the building owner does not want us poking around in their ceiling trying to find them.  The one on the bench I can do a factory reset on, however I don't see the need. It will join the 3504 without issue.   It just won't join the 2504.  I have had 3802s on 2504s for several years.  I don't understand why this is happening, and it appears as if it won't join a 2504 only after it has been on a 9800.

[marce1000]

                     >... it is almost as if the 3802 has been on a 9800, the AP won't ever go back to a 2504.
 - To be expected in those cases the IOS-XE capwap image is not (or no longer) compatible for downgrade to the 2504 aireos based capwap image ; you need to install the matching software manually on the AP ,

 M.

[denneht]

Regarding, "- To be expected in those cases the IOS-XE capwap image is not (or no longer) compatible for downgrade to the 2504 aireos based capwap image ; you need to install the matching software manually on the AP"

I have noticed that when I first had a 9800-L to test with, I could move 3802s between a 9800 and 3504.  

I was able to get the 3802 to join a 2504 last night.  The only reason I am trying to use multiple controllers at this point is because the building is remote from me.  I am doing all the testing on the bench here where I am, since it is an hour away.  When I connected the APs on the ceiling to our switch and pointed them to the 5520, they would NOT join.  So now I am testing this on the bench to figure out what could be wrong.  At the building, everything is pingable, APs get IP addresses and try to join the 5520, but don't.  I thought that maybe the code didn't match.  5520 is running 8.5.171.0

[marce1000 · Accepted solution]

 - Versioning  restrictions are shown in detail here : https://community.cisco.com/t5/wireless/is-it-possible-to-revert-an-ap-2800-back-from-ios-xe-to-aireos/m-p/4576986#M239931

 M.