Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi All, Three AP2802 LED is cycling on Red-Off-Green-Off-Blue-Off. All APs can be seen already on 5520 WLC. According to the starting guide "Access point location command invoked". Two out of three are already added in AP group but all of them have ...
Any tool, application, method to produce Wi-Fi heat-maps for the MR APs before deployment? Thank you
Hello, there is a CISCO recomendation that says the native vlan has to be an unused vlan (a dummy vlan) in order to prevent VLAN hopping attacks.How to achieve this in a wireless scenario?I have a virtual wireless controller and a lot of flex connect...
Hello i am having issues accessing the web GUI on my ISR i have verified that secure web is enabled and i am able to ping the devices IP but when trying to HTTPS i get a "The connection was reset." error looking for some advice on the issue thank y...
Hi,Im configuring AP C9105 switched AP on 9800 WLC. its flex local switching with AP ports to act as a switch in different VLANs. should I use the existing Policy TAG with WLCAN-POLICY MAPs and add RLAN-Policy Maps or create a new policy TAG dedicat...
Hi guys,I currently have seven /22 IP networks for my wireless clients, which are bonded in one Interface Group. Have anyone analyzed if there is some performance penalty for larger segments like broadcast/multicast traffic? What is the recommendatio...
We’re currently experiencing issues with our Guest SSID WiFi. Several users in the office are unable to connect, even when they are near an access point. The connection process gets stuck and keeps repeating.We’ve already rebooted the affected AP, bu...
Hello, We have been working on this issue for a couple of weeks now We have around 10-15 9800's across all of our sites and in one area specifically we are seeing the issue where We are authenticated through DOT1X through ISE, we are seeing the packe...
I have a Cisco AIR-AP3802I-B-K9 access point and I'm trying to convert it to run Mobility Express. I downloaded a Mobility Express image (AIR-AP3800-K9-ME-8-10-196-0) and uploaded it via CLI, and while the AP seems to accept the image, it’s not funct...
Hello! I would like to know if there is any documentation or success stories about installing Meraki access points on boats or ferries.
Good Morning, Just wondering if anyone has managed to setup radsec between Meraki APs and Cisco ISE. I'm certain I've setup both environments correctly, but authentication (pass or fail) isn't showing with the ISE logs, so suspect it's an issue with ...
We are running ISE 3.1 and I have plans to upgrade the C9800 to 17.9.x (which is the recommended one). But I see in the release notes that ISE 3.1 is not listed in the compatibility matrix.Is it true that ISE 3.1 is not supported?!https://www.cisco.c...
Hi, I was doing research and know that 17.9.3 was the latest IOS that reintroduced compatibility for Wave 1 APs. What doesn't seem clear is whether that is the only one. Does reintroduced mean all of 17.9.x will be compatible? Or is 17.9.3 the latest...
Hello, I have a Cisco AIR-AP2802I-B-K9 running ME version 8.10.196.0. I can configure any wireless 2.4 GHz networks without issues, but when I configure a 5 GHz network, I'm not seeing the network on any device that supports it. What can I do? It set...
I have a CW9178i Connected to a MS150 on two 5G ethernet ports The AP and the Ports running LACP. All works well except when you upgrade the firmware... the AP does not come back online... when you check the switch the first port gets disabled by LAC...
