02-20-2017 10:40 PM - edited 07-05-2021 06:35 AM
Hi Team,
We had purchased 3802i model Access point recently, we would like to work with standalone mode, so i tried to download the Autonomous IOS from cisco website, but this software doesn't available. can someone do help to resolve this?
For Information : we had a contract for this AP and also our CISCO ID has associated with contract.
Thanks
02-20-2017 10:49 PM
https://supportforums.cisco.com/discussion/13230486/needs-download-autonomous-ios-air-ap3802i-d-k9
Kindly don't make multiple copies of one topic
02-20-2017 10:58 PM
Starting with the 1800/2800/3800, there is no more "autonomous" or "standalone" mode. Cisco has changed that to Cisco Mobility Express.
To convert the AP from controller-based IOS to Mobility Express, read THIS.
Don't forget to rate our useful posts.
02-20-2017 11:47 PM
Hi Leo,
Thanks for your valuable reply, meanwhile i just wants to know some details
1. I am going to directly connect this AP to ISP (not through switch) , so i need to create dhcp in AP only, Is it possible in Mobility Express?
2. I want to configure one IP address to AP for Management before the Mobility Express IOS upgrade to AP , How to do it? Please explain
Thanks
02-20-2017 11:57 PM
1. I am going to directly connect this AP to ISP (not through switch) , so i need to create dhcp in AP only, Is it possible in Mobility Express?
Yes, you can create a DHCP scope.
02-21-2017 12:03 AM
Thanks Leo,
Can you give some idea about my 2nd question?
02-21-2017 12:42 AM
Please read the Getting Started Guide.
02-22-2017 12:22 AM
Hi Leo,
As per the document, I have assigned the IP address to the AP through the following command
#capwap ap ip 10.0.0.2 255.255.255.0 10.0.0.1
then, i have assigned the ip address to the system
10.0.0.1 255.255.255.0 default gateway 10.0.0.1
den i have tried to upload the image through below command
#ap-type mobility-express tftp://10.0.0.1/AIR-AP3800-K9-ME-8-3-102-0.tar
after that following commands is showing in my console
AP0042.68C6.08D0#ap-type mobility-express tftp://10.0.0.1/[*01/01/2016 10:43:06.0181] CAPWAP State: Discovery
[*01/01/2016 10:43:06.0182] Did not get log server settings from DHCP.
[*01/01/2016 10:43:15.5208] CAPWAP State: Discovery
[*01/01/2016 10:43:15.5209] Did not get log server settings from DHCP.
AP0042.68C6.08D0#ap-type mobility-express tftp://10.0.0.1/AIR-AP3800-K9-ME-8-3-102-0.tar[*01/01/2016 10:43:25.0236] CAPWAP State: Discovery
[*01/01/2016 10:43:25.0237] Did not get log server settings from DHCP.
AP0042.68C6.08D0#ap-type mobility-express tftp://10.0.0.1/AIR-AP3800-K9-ME-8-3-102-0.tar
Starting the ME image download...
It may take a few minutes to finish download.
If it is longer, please abort command, check network connection and try again
[*01/01/2016 10:43:34.5263] CAPWAP State: Discovery
[*01/01/2016 10:43:34.5264] Did not get log server settings from DHCP.
[*01/01/2016 10:43:44.0291] CAPWAP State: Discovery
[*01/01/2016 10:43:44.0292] Did not get log server settings from DHCP.
[*01/01/2016 10:43:53.5319] CAPWAP State: Discovery
[*01/01/2016 10:43:53.5323] Did not get log server settings from DHCP.
[*01/01/2016 10:44:03.0346] CAPWAP State: Discovery
[*01/01/2016 10:44:03.0347] Did not get log server settings from DHCP.
[*01/01/2016 10:44:12.5374] CAPWAP State: Discovery
[*01/01/2016 10:44:12.5375] Did not get log server settings from DHCP.
I have mentioned the #sh version details in below
Processor board ID FGL2026X9N8
AP Running Image : 8.2.20.16
Primary Boot Image : 8.2.20.16
Backup Boot Image : 0.0.0.0
1 Multigigabit Ethernet interfaces
1 Gigabit Ethernet interfaces
2 802.11 Radios
Radio Driver version : 9.0.5.5-W8964
Radio FW version : 9.1.8.1
NSS FW version :
Base ethernet MAC Address : 00:42:68:C6:08:D0
Part Number : 73-017278-05
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC20230UW4
Top Assembly Part Number : 068-100531-01
Top Assembly Serial Number : FGL2026X9N8
Top Revision Number : A0
Product/Model Number : AIR-AP3802I-D-K9
AP0042.68C6.08D0#[*01/01/2016 10:37:42.9236] CAPWAP State: Discovery
[*01/01/2016 10:37:42.9237] Did not get log server settings from DHCP.
Kindly check my process whether i am doing correct or not? still i am not able to upload the Mobility Express image, Please help
02-22-2017 12:50 AM
The AP wants the IP address to be DHCP.
02-22-2017 01:06 AM
but i am not using any DHCP server, i have configured IP manually to AP, Is there any possiblities ?
02-26-2017 08:03 PM
Please Update you firmware to 8.3.
Use the following guide to setup :
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/83/user_guide/b_ME_User_Guide_83/b_ME_User_Guide_83_chapter_01000.html
If the issue persists further please contact Cisco TAC as you have a contract
03-13-2017 07:56 PM
02-28-2018 10:29 PM
To configure standalone Cisco access point :-
1. Assign static IP address to AP
2. Create SSID name of WLAN1
3. Broadcast the SSID
4. NO security
5. Enable wireless interfaces
6. Check connectivity
7. Configure AP with a WPA2 PSK authentication
12-05-2022 04:30 AM
Hi
Iam reset the cisco AIR-AP3802I-D-k9 showing below screen. i am not able to assign to ip address. DHCP also not taking please give me suggestion how to assign ip address to air point.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide