I am attempting to obtain a copy of the WLC config from the controller via FTP from GUI and SSH. Multiple FTP/TFTP servers have been attempted, but we keep getting the following error. cisco updcode.c:6888 Error FTP file Transfer [ftp_put], <150>, Op...
Forum Posts
Resolved! Cisco WLC 5520 GUI and CLI stuck
Hello,We have an EMEA central WLC, Cisco 5520 in HA with firmware 8.5.171.0, hosting around 400+ APs among multiple countries and sites, I was working on the CLI for reviewing some APs logs earlier, at a moment it got stuck.Since this moment I cannot...
All access points (APs) under my C9800-80 controller are operating in local mode. I have two different SSIDs: one with WPA2 Enterprise and the other with open (central web authentication with ISE). There doesn’t appear to be a general issue, everyth...
Hoping to get some help here... we are baffled.There are 400+ commercial IoT devices (all the same) on the wireless network across several campuses. These devices have always connected very quickly and have been very stable.Internet shortages, chip ...
1. trying to block DNS IP (which is outside AdP domain) from a device in IOT .. IOT has tag 268, for DNS I create an adaptive policy object with DNS IP, then tied policy object to an SGT (10) in a group, then created a policy to block traffic between...
i am looking for the SNMP OID, to check what is AP name that a specific client is connected at. for example, a client 01:02:03:AA:BB:CC is currently connected to "AP123". i am looking for the SNMP OID, which can return the name "AP123", protocol (802...
I am seeing multiple issues with assigning SGTs, I have relevant HW ad Licenses.when I assign SGT at SSID level the SGT disappears as soon as I save itafter savingI though it may be cosmetic, the capture on wired interface do not show any CMD header....
HelloI have a C9120AXE access point. I'm trying to change the bandwith using SSH command: "ap name AP84F1.4783.21FC dot11 dual-band channel width 40W" but it fails with the following error printed on the serial console: "%RRM_CLIENT-3-EWLC_EXEC_ERR: ...
Hello, did anybody tried to connect prime intra 3.10.4 (last version) with CMX 11.0.1 (last version)? combability matrix says it should work but I get "CMX Reachability issue. Please check logs for more information" Sure, it is almost impossible to...
Hello,I seem to be having a PoE problem with AIR-AP1832I-E-K9 WAPs connecting to C9300-LM switches. This AP model has worked fine for a good few years connected to a C3560 switch. The switch has been replaced with a 9300-LM and power is granted for a...
Hi All, I am using Cisco 9800-CL as the WLC and the Microsoft NPS as the Radius Server. I need to know whether the same client can be authenticated from both the methods EAP-PEAP and EAP-TLS simultaneously. As a brief, user need to log in to the same...
Hi guys, I recently migrated from vWLC to C9800CL, took me a while to get use to the new platform but luckly so far so good. One interesting issue through, when testing the speed over 802.11ac 5ghz, it seems like there is a bottle neck at 500mbps. I ...
We have enable webauth redirection from WLC 2504 so that when any user connect to SSID he can get a webpage to input username and password. But the problem is, user initially can connect SSID with username and password but that user have to put usern...
Hello everyone, I would like to understand more specifically the workaround suggested in CSCwb69128 which says: "Disable the padding option on the client device". Would this mean disabling the PMK cache if the endpoint is Windows?
Sir,We are procuring few AP we configure as mesh. but we are facing several issuesCurrently experiencing sticky client issues. Occasional Wi-Fi connection drops when switching between APs. Some devices switch between 5GHz and 2.4GHz frequencies unexp...
